• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.5-8
• /
• 2010

The GCSC injectors studied in this paper are those applied to the combustion chamber of staged combustion engines. Liquid fuel is injected through tangential holes along the outer wall of the GCSC injector forming a swirling sheet and oxygen rich gas generated by a preburner enters axially through the center orifice of the injector to form a gaseous jet. The spray characteristics of GCSC injectors under ambient/high pressure conditions and the effect of recess on spray characteristics have been examined in this paper. These results are expected to be used as fundamental data to develop of a staged combustion engine.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.1
• /
• pp.13-21
• /
• 2000

The advantages of the SITVC (Secondary Injection for Thrust Vector Control) technique over mechanical thrust vectoring systems include a reduction in both the nozzle weight and complexity due to the elimination of the mechanical actuators that are used in conventional vectoring. The optimal operating conditions of SITVC were investigated using in-house developed compressible flow analysis codes. Numerical experiments were used to examine the impact of the thrust vector direction with a variety of injection positions, mass flow rates, and injection angles on the two-dimensional expansion cone of a supersonic nozzle. The computational results showed that the optimal position of the secondary injection, with the maximum deviation angle and side thrust, was where the oblique shock generated by the secondary injection reached the end of the nozzle exit.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.1
• /
• pp.24-33
• /
• 2020

In this study, model combustion tests were conducted to investigate the combustion instability characteristics of swirl coaxial injectors for a liquid rocket engine. To examine the effects of the combustion chamber resonant frequency and the injector mixing conditions, pressure fluctuations in the combustion chamber were measured by changing the combustion chamber length, injector recess length, and propellant mixture ratio. From the test results, the variation in the pressure fluctuations for each experimental condition was confirmed and the combustion stability was evaluated by stability mapping. It was found that the longitudinal mode and Kelvin-Helmholtz instabilities occurred due to the change in the combustion chamber and recess lengths.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.197-201
• /
• 2006

In the development process of a fuel-rich gas generator using kerosene and LOx for a 30 tonf class liquid rocket engine, a heat damage occurred at the LOx post of swirl coaxial injectors used in the gas generator and the problem has been examined. To prevent the heat damage, injectors are redesigned to have an increased recess while maintaining internal mixing, which minimizes recirculation region to prevent anchoring of the flame in the recirculation region. The combustion test results of the sub-scale gas generator showed that this scheme can prevent heat damage of the LOx post in the swirl coaxial injectors of the fuel-rich gas generator.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.49-53
• /
• 2009

The paper presents the results of the experimental study about flow discharge characteristics of double swirl coaxial injectors for a liquid rocket engine. Flow discharge characteristics of injectors become one of critical design issues for LRE combustion devices. Tap water and liquid oxygen/kerosene were used for ambient and hot firing tests, respectively. A combustion discharge coefficient varies depending on a mixture ratio and a recess ratio, and magnitudes of the variations are different with respect to injector shapes and operating conditions. The variation of a combustion discharge coefficient with a LOx injector is considered to result from flame structure changes due to physical property changes.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.57-63
• /
• 2017

In this study, the fundamental test for drag reduction is carried out by using a plasma generator. Fundamental test setup is constructed of visualization and drag measurement system. The schlieren technique is used to visualize the plasma counterflow in supersonic flow. The penetration of the plasma jet and the change of the flow structure are observed through visualization results. Load cell is used to confirm possibility of drag reduction. Results show that drag was reduced by 6.2% using plasma jet in supersonic flow.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.245-250
• /
• 2004

The objective of the present study is to conduct model combustion tests for various injectors to identify their combustion stability characteristics. Three different double swirl coaxial injectors with variation of a recess number have been tested for the comparative study of stability characteristic and flame structure. Gaseous oxygen and mixture of gaseous methane and propane have been employed for simulating actual propellants used for a fullscale thrust chamber. Upon test results, the direct comparison between various types of injectors can be realized for the selection of the best design among prospective injectors.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.475-481
• /
• 2017

In this paper, high speed camera images were used to analyze the supercritical injection behavior of liquid hydrocarbon compounds used as main components of propellant fuel. Decane and Methylcyclohexane (MCH), which have different critical points among kerosene constituents, were selected as experimental fluid and Shadowgraphy technique was used for the analysis. The difference in the temperature variation from the initial injector state of the subcritical condition until the vaporization occurs was represented by the different behaviors of Decane and MCH. However, under the Supercritical conditions, the enthalpy of vaporization near the critical point approaches zero and the phase change to the Supercritical phase occurs instead of vaporization process. In the phase change of the Supercritical system, there was no rapid density change, so the liquid state image was observed in both the Decane and MCH.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.5
• /
• pp.130-135
• /
• 2013

Anti-icing system can reduce traffic accidents and congestion by quickly removing the frozen road surface area. there is no decision criteria for determining application of the Anti-icing system in Korea. In this study, we proposed the decision criteria for determining application of the anti-icing system based on weather and road conditions, i.e., geometric and topographic conditions. Regional climate survey, Solar Radiation analysis, and dynamic vehicle simulation considered road geometry was conducted to standardize the installation method of anti-icing system. Also, we have developed a software that can be determined an installation of anti-icing system.

• Fire Science and Engineering
• /
• v.20 no.2 s.62
• /
• pp.44-53
• /
• 2006

We have conducted a numerical simulation under two-dimensional unsteady conditions in order to analyze the effect according to the injection angle and velocity of the $CO_2$ agent nozzle which is one of the elements for the fixed type $CO_2$ fire extinguishing system installed in a ship on the characteristics of flow and $CO_2$ concentration distribution. The flow fields and concentration fields were measured and analyzed. We can found that the difference of flow patterns according to the conditions of $CO_2$ agent injection nozzle, and in all the conditions of $CO_2$ agent injection nozzle, the iso-concentration line was expanded from the region at which vortex was generated to the surroundings. We can expected that the intensity of the wall jet on the bottom floor was generated differently and the iso-concentration lines were expanded or shrunk according to the angle of $CO_2$ agent injection nozzle. In case of increasing $CO_2$ agent injection velocity maintaining the flow quantity of the $CO_2$ agent injection equally, the iso-concentration line of $CO_2$ agent on bottom floor can be formed more higher than in case of decreasing $CO_2$ agent injection velocity.