• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.512-512
• /
• 2017

날로 심각해지는 해수 오염, 유류사고, 해파리에 의한 인명피해 및 발전소의 경제적 피해사고, 해양 쓰레기 등과 같은 해양 환경 문제가 발생하고 있다. 이러한 해양환경문제를 해결하기위해 생물학적 방법과 물리적 방법이 있으나 생물학적 방법은 개체군과 종류의 변화로 그 적용이 어려운 실정이고, 물리적 방법은 지속적인 제거를 위한 비용적인 문제와 인부 및 자원봉사자의 안전문제가 발생한다. 따라서 에어버블을 이용한 각종 친환경적 방법이 주목받고 있다. 본 연구에서는 에어버블 차단막의 차단율을 증가시키기 위해 현장조건 내에서 에어버블의 거동특성에 대한 실험을 하였다. 실험을 위해 회류식 개수로 에어버블 거동실험장치를 제작하였다. 실험장치는 길이 8.1m, 높이 1.2m, 폭 0.7m이며, 두께 10mm의 투명 아크릴를 사용하여 에어버블의 거동을 관찰 할 수 있게하였다. 대형펌프를 사용하여 물이 회류함을 통해 흐름유속을 만들어 현장조건을 고려하였다. 에어버블을 분사하기 위해 압축공기 저장탱크와 연결된 분사구가 있으며, 노즐의 크기(0.5mm~1.0mm)로 분사량을 조절하고 분사압은 별도의 조절장치를 이용하여 0~5bar 범위의 분사압 조절을 가능하게 하였다. 초고속 카메라와 3축유속계를 사용하여 에어버블의 이동경로, 유속 및 에어버블의 거동을 측정하였다. 실험을 통한 구간별 에어버블의 거동 분석 결과, 상승속도는 분사구에서 분출되는 구간인 0~0.8m 에서는 상승속도가 증가하고, 0.8~1.2m구간에서는 속도가 다시 상승하는 경향을 확인하였다. 이는 수표면에 가까워질수록 수압이 작아져서 에어버블의 크기가 커짐에 따라 부력이 커짐으로 판단된다. 같은 이유로 분사량이 많을수록 상승속도도 같이 증가되는 것으로 나타났다. 유속에 따른 거동은 유속을 0.1m/s~0.5m/s로 조정하여 유속별 에어버블이 수표면까지 도달하는 거리, 속도 및 이동경로를 분석하였다. 유속과 에어버블이 수표면까지 도달하는 거리는 비례하여 증가하는 것을 확인하였다. 실험결과를 바탕으로 조건에 따른 에어버블 거동 경험식을 도출하였다. 본 실험은 회류식 개수로 에어버블 거동실험장치를 활용하여 에어버블 거동 경험식을 제시하였으며, 이를 바탕으로 에어버블 차단막 기술 개발을 위한 기초자료로 이용될 수 있을 것이다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.288-291
• /
• 2004

The spray characteristics of coaxial swirl injector under ambient high pressure conditions were investigated in this paper. Three injectors were used to study the effect of recess length and fuel injector type(open or closed). In this research, experimental conditions(ambient gas density) were calculated by Buckingham Pi-theory and spray characteristics of the injectors were represented by mass flow rate according to the injection pressure, the spray angle, mass distribution, and mean diameter of droplet.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.5
• /
• pp.82-92
• /
• 1996

A computer simulation with predict the fuel injection rates and the fuel injection pressure behaviors in diesel engine fuel injection systems would by very useful in designing or improving fuel injection systems. In this paper we developed computer program in order to predict the behaviors of the fuel injection rate and the injection pressure for Electronic Hydraulic Ultra-High Pressure Fuel Injection System. We've applied the continuity and momentum equations for the hydraulic phenomena and the dynamics of individual components of the Electronic Hydraulic Fuel Injection System. To solve all the equations numerically we've applied the Runge-kutta IV method. Water hammer equations were applied for the hydraulic pipe solution, and the method of characteristics was employed in our calculations. The simulation results were compared with the experimental results for: Accumulator pressure, Injection pressure and unjection rate. As a result, The simulation results agree very well with our experimental results. We found that a large accumulator and the high speed solenoid valve were required, and the compression volume of the fuel had to be as small as possible in order to acheive ultra-high pressure fuel injection.

• Journal of ILASS-Korea
• /
• v.18 no.1
• /
• pp.21-26
• /
• 2013

Diesel low temperature combustion (LTC) is the concept where fuel is burned at a low temperature oxidation regime so that $NO_x$ and particulate matters (PM) can simultaneously be reduced. There are two ways to realize low temperature combustion in compression ignition engines. One is to supply a large amount of EGR gas combined with advanced fuel injection timing. The other is to use a moderate level of EGR with fuel injection at near TDC which is generally called Modulated kinetics (MK) method. In this study, the effects of fuel injection pressure on performance and emissions of a single cylinder engine were evaluated using the latter approach. The engine test results show that MK operations were successfully achieved over a range of with 950 to 1050 bar in injection pressure with 16% $O_2$ concentration, and $NO_x$ and PM were significantly suppressed at the same time. In addition, with an increase in fuel injection pressure, the levels of smoke, THC and CO were decreased while $NO_x$ emissions were increased. Moreover, as fuel injection timing retarded to TDC, more THC and CO emissions were generated, but smoke and $NO_x$ were decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.597-600
• /
• 2010

Cold flow injection test was conducted to investigate the characteristics of cryogenic liquid nitrogen jet at sub to supercritical condition. Single jet injector element was installed in high pressure chamber to investigate the effect of ambient pressure around the jet, injector geometry and flow conditions. Experimental results showed obvious differences between jet characteristics under subcritical and supercritical condition. Effect of injector inlet shape also was investigated.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.323-328
• /
• 2002

양파의 껍질에 칼금을 내고 꼭지와 뿌리를 절단한 후 회전하는 두 개의 롤러 위에 양파를 낙하시켜 구르게 하면서 그 위에 고압공기를 분사시켜 양파의 외각 껍질을 제거하는 공기분사식 박피장치의 최적 작동조건을 구명하기 위하여 수행한 시험결과를 요약하면 다음과 같다. 1, 박피장치에 고압공기를 분사하지 않았을 때, 롤러의 원주속도가 빠를수록, 양파의 무게가 가벼울수록 구름소요시간은 줄어들었고 직경방향 구름율이 가장 높았는데, 직경방향 구름소요시간이 가장 짧게 나타나는 주롤러의 원주속도는 2.4 m/s이었다. 2. 주롤러의 원주속도 2.4 m/s일 때 양파의 무게, 분사공기압 및 칼금수가 증가할수록 박피율은 증가하였으며, 박피율이 가장 높은 조건은 칼금수 4개, 분사공기압 3.5 kg/$cm^2$이상이었다. 3. 박피소요시간은 칼금수가 많을수록, 분사공기압이 높을수록 짧아지는 것으로 나타났고, 칼금수를 4개로 하고 분사공기압을 4.0 kg/$cm^2$이상으로 하면 박피소요시간을 2초 이하로 유지할 수 었다. 4. 양파의 껍질강도는 저장기일과 조건에 따라 다르므로 모든 양파의 박피를 위해서는 분사 공기압을 4.0 kg/$cm^2$이상으로 하고 공기분사시간을 2초에서 5초가지 조절할 수 있는 장치를 부착하는 것이 좋을 것으로 판단된다. 5. 시험에 사용된 양파는 무게는 150~350$\pm$30 g, 직경 60~120 mm의 크기로 우리나라에서 생산되는 양파의 98%에 적용이 가능할 것으로 생각된다.

• Journal of ILASS-Korea
• /
• v.20 no.1
• /
• pp.43-52
• /
• 2015

Experimental study was conducted to investigate the effects of ultra-high injection pressure and nozzle hole diameter on diesel flow and spray characteristics. Electronically controlled ultra-high pressure fuel injection system was made to supply the fuel of ultra-high pressure consistently. Three injection pressures, 80, 160, and 250MPa were applied. Four type of injectors with identical eight nozzle holes were used. The four injectors have nozzle hole diameters of 115, 105, 95, and $85{\mu}m$ respectively. Injection quantity and rate were measured to investigate flow characteristics according to injection pressures and nozzle hole diameters. Mie-scattering and shadowgraph were performed to visualize liquid and vapor phases of diesel spray in a constant volume combustion chamber (CVCC). Ambient conditions of high pressure and high temperature in a diesel engine were simulated by using CVCC.

• Journal of ILASS-Korea
• /
• v.4 no.1
• /
• pp.34-44
• /
• 1999

The purposes of this study were to evaluate engine performance and to analyze smoke emission characteristics for varied injection pressures and engine operating conditions of an electronically-controlled ultra high pressure fuel injection system(UHPFIS). It was discovered that the engine performance with the present UHPFIS was far better than what was initially expected. And the UHPFIS permitted engine operation at air/fuel ratios richer than 20 : 1 without increasing smoke emissions. It was discovered that the indicated mean effective pressure was increased, while the specific fuel consumption and the amount of soot were decreased, as the fuel rail pressures were improved atomization of the fuel spray. As the intake air temperature was increased from $38\sim205^{\circ}C$ in 38 degree increments, the indicated mean effective pressure was dropped while the specific fuel consumption was increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.137-146
• /
• 1996

Behaviour of ultra-high pressure diesel spray and its structure in a constant-volume pressure chamber were studied with injection pressure ranging from 35 to 110MPa. Sprays were observed by using the back illumination scattering method and righ angle scattering method. The spray process mechanism were investigated with both photographs. As a result, the spray angle and air entrainment angle was larger as injection pressure and back pressure increase. It becomes clear that mean air-fuel ratio is increased by increasing the injection pressure.