• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.4
• /
• pp.10-21
• /
• 2014

The joint of prefabricated steel grid composite deck is composed of concrete shear key and high-tension bolts. The flexural and shear strength of the joint were experimentally evaluated only by the bending and push-out test of the joint element. In this study the lateral load transfer behavior of the joint in deck structure system is experimentally evaluated. Several decks connected by the joint are prefabricated and loaded centrically and eccentrically. In the case of centrically loaded specimens, the analysis results show that for the same loading step the rotation angle of the joint with 4 high-tension bolts is larger than the case of the joint with 9 high-tension bolts. Consequently, flexural stiffness of deck and lateral load transfer decrease in the case of specimen with 4 high-tension bolts. But, in the case of eccentrically loaded specimens, it is found that there are no significant differences in the load transfer behavior. The further analysis results about the structural behavior of the joint show that lateral load transfer can be restricted by the load bearing capacity of the joint as well as punching shear strength of the slab. Furthermore, considering that high-tension bolts in the joint didn't reach to the yielding condition until the punching shear failure, increase in the number of high-tension bolts from 4 to 9 has a greater effect on the flexural stiffness of the joint and deck system than the strength of them.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.2
• /
• pp.187-196
• /
• 1999

An experimental investigation was conducted to study the structural behavior of concrete columns confined with welded grids. The full-scale columns with different volumetric ratio, spacing and arrangement of welded reinforcement grids were tested under simulated seismic loading. The columns were subjected to constant axial compression of approximately 20% or 40% of their capacities accompanied by incrementally increasing lateral deformation reversals. The results indicate that the welded reinforcement grid can be used effectively as confinement reinforcement provided that the steel used, have sufficient ductility and the welding process employed does not alter the strength and elongation characteristics of steel. The grids improved the structural performance of columns, which developed lateral drift ratios in excess of 3% with the spacing and volumetric ratio of transverse reinforcement similar to those required by the ACI 318-95 Building Code. Drift capacity further increased when grids with larger number of cells were used. Furthermore, the use of grids reduced congesting of reinforcement while the dimensional accuracy provided perfect support to longitudinal reinforcement.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.1-10
• /
• 2004

A study on the evaluation of proper spacing and required flexural rigidity of cross beams in composite two I-section steel girder bridges without a lateral and sway bracing system was performed. Specifically, a 2-lane, 40-m simple span bridge and a 3-span continuous (40+50+10m) bridge were designed, and structural analyses under dead load before and after composite, live, wind, and seismic loads were performed using spacing and flexural rigidity or cross beams as parameters. Through parametric analysis, the effect on the stresses due to the combination of loads and live load distribution was investigated. In addition. material and geometric nonlinear analyses under dead load before composite were performed to evaluate the lateral buckling strength of the steel girders and cross beam. Based on the results or such analyses, the proper spacing and flexural rigidity of cross beams at intermediate points and supports were proposed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1264-1269
• /
• 2008

최근에 이르러 농촌 인구의 도시유입으로 도시의 주거공간이 절대적으로 부족해지고 있으며, 이는 대도시의 아파트 가격 상승을 유발하는 등 부수적인 사회/경제적 문제를 일으키고 있다. 정부나 지방자치단체에서는 이러한 문제를 해결하기 위하여 대규모의 신도시 개발계획을 추진하고 있으며, 이러한 신도시 개발은 도시화로 인하여 환경적, 수문학적으로 영향을 미치는 것으로 조사되고 있으며 도시물순환계는 강우가 지표에 도달 한 후 바로 하천으로 유출되는 것과 침투하여 서서히 유출하는 자연경로 그리고 상수도 및 하수도를 통해 하천으로 배수되는 인공적 경로에 의해서 형성된다. 일반적으로 신도시 개발 전후의 수문순환을 평가하는 방법 중의 하나는 개발예정지에 대한 장단기의 수문 관측을 통하여 개발 전과 개발 후의 유출특성과 수질부하를 정량적으로 비교하는 것이다 (한국건설기술연구원, 2004). 따라서 본 연구에서는 행정중심 복합도시 물순환 해석을 하기 위해 대상유역을 100m 크기의 정방형 격자로 구분하고 기상조건, 지표면 조건, 하천, 토양, 지하 대수층, 농업용수 등의 광범위한 입력 자료를 구축한 후 이를 물리적인 기반의 공간분포모형인 WEP 모형에 적용하여 개발 전 홍수 및 유출특성을 규명하고자 한다. 이를 위해 대상지역에 대한 장기적인 수문모니터링 자료를 바탕으로 1996년에서 2007년 까지 모의 하여 실측자료가 있는 $2006{\sim}2007$년을 대상으로 비교한 결과 일부 갈수기 자료를 제외 하고, 전반적인 높은 상관성을 나타냈다. 하지만 일부 홍수위에서 금강으로 부터의 배수위 영향으로 인한 차이가 발생해 추가적인 검토가 필요하며, 본 연구에서 도출된 결과들은 향후 도시유역에서의 수자원 분배와 물자원 관리 등의 적응전략을 수립하는데 있어 본 연구가 도움이 될 것이라고 판단한다.

• Applied Microscopy
• /
• v.32 no.1
• /
• pp.31-37
• /
• 2002

As-cast microstructure of Mg-rich $Mg_{68}Zn_{28}Y_4$ has been investigated by a detailed transmission electron microscopy. The as-cast $Mg_{68}Zn_{28}Y_4$ alloy consisted of three different types of phases: $10{\sim}20{\mu}m$ size primary solidification phase, dendritic phase grown from the primary phase and a eutectic structure formed at the later stage of solidification. The primary solidification phase has an icosahedral structure with a large degree of phason strain. 1/1 rhombohedral approximant phase with lattice parameters: $a=27.2{\AA}\;and\;{\alpha}=63.43^{\circ}$ is first observed in Mg-Zn-Y system. The rhombohedral structure can be obtained by introducing phason strain in the six dimensional face centered hyper-cubic lattice. The decagonal phase nucleates with orientation relationship with the icosahedral phase, and $Mg_4Zn_7$ nucleates with orientation relationship with the decagonal phase, indicating a close structural similarity between the three phases. Gradual depletion of Y during solidification plays an important role in heterogeneous nucleation of decagonal and $Mg_4Zn_7$ phases from icosahedral and decagonal phases respectively.

• Nuclear Engineering and Technology
• /
• v.6 no.2
• /
• pp.97-111
• /
• 1974

The adsorption mechanism of Cs-137 in low level radioactive solution by vermiculite treated with Na ion is studied in order to investigate its effective utilization for the radioactive effluent treatment. The beneficial role of Na-vermiculite is that Na ion can induce the wider c-axis spacing in which Cs ion can be sorbed in vermiculite. Cation exchange capacity and distribution coefficient of cesium seems to be influenced by the variation of c-axis spacing of vermiculite. Comparative identification and detection with the characteristic analyses of X-ray diffraction and electron diffraction patterns, diffrential thermal analysis and electron microscopy of Na-, K- and Cs-vermiculite are studied for the phemomena of Cs adsorption by vermiculite. This importance of the utilization in terms of adsorption and fixation of cesium involving vermiculite is discussed. It is found that the Na-vermiculite is valuable outside charging material for high level radioactive liquid waste storage tank of underground to protect the pollution of the underground water.

• Korean Journal of Soil Science and Fertilizer
• /
• v.36 no.4
• /
• pp.181-192
• /
• 2003

We developed a mathematical simulation model to portray the vertical distribution of soil water from the measured weather data and the known soil hydraulic properties, and then compared simulation results with the periodically measured soil water profiles obtained on Jungdong sandy loam to verify the model, In this model, we solved potential-based Richards' equation by the implicit finite difference method superimposed on the predictor-corrector scheme. We presumed that: soil hydraulic properties are homogeneous; soil water flows isothermally; hysteresis is not considered; no vapor flows; no heat transfers into the soil profiles; and water added to soil surface is distributed along the soil profile following partial displacement principle. The input data were broadly classified into two groups: (1) daily weather data such as rainfall, maximum and minimum air temperatures, relative humidity and solar radiation and (2) soil hydraulic data to approximate unsaturated hydraulic conductivity and water retention. Each hydraulic polynomial function approximated using the Chebyshev polynomial and least square difference technique in tandem showed a fairly good fit of the given set of data. Vertical distribution of soil water as approximations to the Richards' equation subject to changing surface and phreatic boundaries was solved numerically during 53 days with a comparatively large time increment, and this pattern agreed well with field neutron scattering data, except for the surface 0.1 m slab.

• The Korean Journal of Quaternary Research
• /
• v.22 no.1
• /
• pp.1-12
• /
• 2008

We investigated metal concentrations and oceanic environment changes that have occurred over the past several years by studying the hard coral Porites lutea, which inhabits tropical and subtropical areas. Soft X-radiographs clearly showed distinctive annual bands within 71 mm coral sample, which reflect changes in the oceanic environment over this period. There were large fluctuations in the major and minor element concentrations. Considering the physicochemical partition coefficient, some elements accumulated in the aragonite matrix in a mechanical manner, while others were affected by environmental factors. The concentrations of some heavy metals varied over a wide range, implying local environmental effects. The variation of Sr/Ca and Mg/Ca in coral skeleton clearly showed large-scale fluctuation over the specific intervals, implying environmental changes during this period. The concentrations of heavy metals also show high fluctuations, and roughly accord with Mg/Ca variation. In addition, Cu and Zn seem to show cyclicity-like peaks, coincide with Mg/Ca variation over the specific intervals. Such variation might be related to local pollution and oceanographic changes. More detailed investigation is necessary, including the pretreatment of coral skeleton sediment.

• Proceedings of the ESK Conference
• /
• 1993.10a
• /
• pp.46-55
• /
• 1993

조종사가 수행하는 조종 업무는 여러 정보를 동시에 지각하여 처리하여 야 하는 복잡한 작업으로 구성되어 있어, 조종사에게는 고도의 인간성능이 요구되고 있다. 또한 조종기술을 습득하기 위해서는 많은 훈련시간과 비용 이 소요되며, 조종사의 실수는 치명적인 사고를 초래한다. 따라서 조기에 비행 부적격자를 판별하고, 미흡한 조종 적성을 함양시킬 수 있는 교육 . 훈련 프로그램을 조종 후보생에게 적용시키는 분석적 조종적성 진단 체계 개발은 조 종사의 도태율 감소, 효율적인 비행훈련, 비행 안전사고 감소 등의 측면에서 절실하게 요구되고 있다. 본 연구에서는 조종 업무 수행시 요구되는 여러 인간 기능의 중요도 차이를 조종 적성 평가 체제에 적용하기 위해서, 각 적성 검사 항목들의 상대적 중요도를 분석하고 이의 타당성을 평가하였다. 적성검사 항목의 상대적 중요도 분석은 조종적성검사 계층구조의 각 수준별 쌍체 비교 평가와 AHP(Analytic Hierarchy Process) 분석에 의한 상대적 중요도 산출 및 평가, 그리고 일관성 지수(Consistency Index)에 의한 분석 결과의 조정을 통해 이루어 졌다. 적성검사 항목의 쌍체 비교 평가는 심리기능검사, 비행자질 검사 등 총 29개 적성검사 항목에 대해 검사를 받았고 또한 초등비행 훈련과정을 수료한 조종 학생들에 의해 이루어 졌다. 상대적 중요도를 분석한 결과 심리기능 검사(W=0.30)가 다른 검사에 비하여 조종적성 평가에 중요한 검사로 나타났으며, 세부 항목으로는 주의 분배력(W=0.13), 추적능력(0.06) 등이 상대적으로 중요한 검사 항목으로 나타났다. 또한 상대적 중요도 결과를 적용한 적성검사 성적이 적용하지 않은 적성검사 성적에 비해 비행성적에 대한 예측 능력이 좋은 것으로 평가되었다.al age)가 있다는 것을 의미하는 것이다. 한편, 생산현장에서는 자동화, 기계화가 진보되어 육체적인 노동이 경감된 결과, 중고령자라도 할 수 있는 작업이 많아지고 있다. 또, VDT (Visual Dislay Terminal) 작업과 같은 정보처리 작업의 수요가 증가하여 그 인재의 부족이 지적되고 있다. 따라서 중고령자의 기능을 조사하여 어떠한 작업에 적합한가를 판단하는 것이 중요한 과제로 되었다. 그러나 노동에는 많은 기능이 관여 하고, 그 내용에 따라서 요구되는 기능이 서로 다르기 때문에 노동적응능력의 기본적인 기능으로 보여지는 것에 좁혀서 작업능력의 연령증가 변화에 대하여다원적 평가를 하는 것이 실제적이라고 할 수 있다. 따라서 본 연구에서는 인간이 가지고 있는 다수의 기능중에서 수지교 치성과 연령증가와의 관계를 조사한다. 만약 연령증가 만으로 수지교치성을 평가 할 수 없는 경우에는 어떠한 요인이 수지기민성의 변화에 영향을 미치는가를 검토한다.t list)에서 자동적으로 사건들의 순서가 결정되도록 확장하였으며, 설비 제어방식에 있어서도 FIFO, LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스템에 대한 시뮬레이션 구현과 시스템 분석의 예를 보인다._3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.4
• /
• pp.602-612
• /
• 2010

This study was conducted to investigate the state of hygiene education aimed for by bakers, and the evaluations of the importance and the performance concerning sanitary characteristics by the bakers. The questionnaires were administered to 186 bakers in Busan and the data evaluated by 5 scales method of Likert were statistically analyzed. 20.4% of bakers have not received hygiene education. Only 32.8% of bakers have experienced hygiene education regularly. The more the bakers were educated, the more they practiced the contents of hygiene education. The major reason of education unfulfilment was due to insufficient equipments and facilities. The scores of the hygienic performance of educated bakers were significantly (p<0.05) higher than those of uneducated bakers in food sanitation, especially for sanitary characteristics on inspection, pre-preparation and distribution. The mean scores of the importance and the performance evaluated by bakers were 4.05/5.00 and 3.76/5.00, respectively. The bakers assessed the highest scores on the importance and the performance of personal hygiene. The gap score was -0.30 between the importance and the performance for sanitary characteristics. The baker recognized that sanitary management was not performed as much as they recognized its importance. The importance and the performance grid of bakers revealed that the items of checking the certification for the origin of new food ingredient, inspecting deliveries as quickly as possible, separation between preparing and breading time, thawing frozen food under running tap water/in refrigerator, separating disposal gloves and utensils by the purpose, putting products in cleaned and sterilized utensils, letting consumes know the expiration date of products, preventing a rubber hose from being left on the kitchen floor, checking insect nets frequently and so on showed lower scores compared to the mean scores of the importance and the performance. The levels of the hygienic performance by bakers were positively correlated (p<0.01) with the recognitions of the importance on sanitary characteristics. These results might provide basic data for hygienic training and play a role on the improvement of the sanitary management in bakery.