• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.10
• /
• pp.1451-1457
• /
• 2002

When an aqueous liquid such as water having high electric conductivity and high surface tension is discharged from a nozzle under a strong DC electric field, fine drops ranging from 30 to 450 microns can be obtained only through the spindle mode. In the present study, effects of the electric conductivity and the surface wettability of nozzle materials on formation of drops with this mode were investigated. For that, three nozzles with the same size but with different materials were prepared and tested; a stainless steel needle, and a plain and a metal (gold)-coated (except for the tip portion) silica needles. Uniform drops were obtained with the gold-coated silica nozzle over the wider range of the DC voltage input. That is, formation of the liquid cone and detachment of the liquid spindle (ligament) can be more stabilized and frequent with the needles having high electric conductivity but with low surface wettability at their tips.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.3
• /
• pp.320-327
• /
• 2002

An experimental study of heat transfer from hot flat surface to water sprays was conducted in high temperature region. Heat transfer measurements for hot flat surface were made by 4 sheathed C-A thermocouples. Droplets volume flux were also measured-independently at a position in spray field. The test conditions included variations in droplets volume flux, subcooling of cooling water of $1.565\times10^{-3} to 14.089\times10^{-3}m^3/m^2s and 80 to $20^{\circ}C$ respectively. The effects of inclination angle on heat transfer were investigated and changes in inclination angle of hot flat surface affected heat transfer coefficients of high temperature region.

• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.194-201
• /
• 2000

This paper is intended to analyze the macroscopic behavior and transient atomization characteristics of the high-pressure gasoline injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. Time-resolved droplet axial and radial velocity components and droplet diameter were measured at many probe positions in both axial and radial directions by a two-component phase Doppler particle analyzer (PDPA). In order to obtain the influence of fuel injection pressure, the macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 3,5 and 7 MPa of injection pressure under different surrounding pressure in the spray chamber. The results of this work show that the fuel injection pressure of gasoline injector in GDI engine has influence upon the mean droplet diameter, mean velocity of spray droplet, the spray tip penetration, and spray width under the elevated ambient pressure.

• Journal of ILASS-Korea
• /
• v.2 no.1
• /
• pp.8-17
• /
• 1997

A study has been carried out on the instability of a conical liquid sheet by using the linear instability theory. Various analytical methods using the Kelvin-Helmholtz instability theory were tried to examine the wave growth on cylindrical liquid sheets. Cylinderical liquid sheets were extended to the case with the conical sheets. Perturbations due to tangential motion as well as longitudinal one were taken into account. And it was assumed the the breakup occurs when amplitude ratio exceeds exp(12), drop sizes were predicted only by theoretical approach. The predicted drop size agreed well with the measured Sauter mean diameter, $D_{32}$.

• Journal of ILASS-Korea
• /
• v.3 no.3
• /
• pp.1-13
• /
• 1998

In this study, an experimental study was performed to investigate the breakup mechanism of vaporizing droplet. A well-controlled experimental apparatus was used to study breakup mechanisms of a monodisperse stream of drops injected into a transverse high temperature and velocity air stream. The experiments gave information$ about the microscopic structure of the liquid drop breakup process, drop breakup regimes, and drop trajectories in high temperature flow region. The breakup time, drop acceleration and wavelength of surface instability wave were measured from a high-magnification and double spark photography. The two instability theories, i.e., Kelvin-Helmholtz instability and Rayleigh-Taylor instability, were estimated by comparing the calculated data with the measurements. The results showed that the breakup time in high temperature flow condition is shortened because the surface tension is decreased by the increase of gas temperature.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.295-298
• /
• 2002

In the analysis of the mass distribution and SMD (Sauter Mean Diameter), planar laser imaging technique Is a convenient and useful one when compared to the mechanical patternator or PDPA (Phase Doppler Particle Analyzer). But for the accurate usage of this laser technique, it is required to compensate the signal attenuation and to find the attenuation coefficients. In the present research, we considered effects of the spray distributions on the attenuation coefficient and improved the accuracy of planar laser imaging technique by the reduction of errors issuing from the signal attenuation.

• Journal of ILASS-Korea
• /
• v.9 no.3
• /
• pp.29-34
• /
• 2004

To investigate characteristics and micro-explosion of single-droplets of emulsified fuel, water is mixed with diesel oil by using ultrasonic energy fuel feeding system. The fuel characteristics is analysed through H-NMR spectrum and micro-explosion phenomena of the emulsified fuel is also investigated. The life times of droplets of conventional diesel fuel, ultrasonic energy added diesel fuel and emulsified fuel we obtained additionally. According to this study, the micro-explosion phenomena of single-droplets happen in atmospheric pressure condition, a curve form of emulsified fuel's life tim is different from diesel fuel's one and the change of chemical structures is a cause of ultrasonic-energy-added diesel fuel effect.

• Journal of ILASS-Korea
• /
• v.13 no.2
• /
• pp.73-78
• /
• 2008

An experimental study was performed to explore the drop formation and atomization characteristics in electrohydrodynarnic atomization with flow rate, power supply, voltage frequency, and nozzle size. A basic electrohydrodynarnic atomizer equipment was developed for the analysis of spray visualization and tested for the exploration of relationship between several experimental parameters. In results, the varicose wave had been taken place and the small droplets had been generated less than outer diameter of nozzle on the conditions of 25G of nozzle, flow rate of 2 mL/min, and applied frequency of 50kV at AC power over 5kV voltage. The whipping motion had been grown at applied frequency of 400kV and AC power around 2kV voltage

• Journal of Industrial Technology
• /
• v.35
• /
• pp.67-71
• /
• 2015

Various structures of particles were prepared by electrospray technique. In this research, solid particles were formed by electrospraying a solution of ethanol containing polyvinyl and tetraethyl orthosilicate. During the electrospray process, the ethanol solvent was evaporated, resulting in the solidification of precursors, forming solid particles. Evaporation of ethanol solvent also enhanced the mass transport which facilitated the development of porous and hollow structures.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.5
• /
• pp.25-32
• /
• 2000

In this paper, experiments investigating the high-temperature region heat transfer coefficients for the spray cooling of hot flat plates were performed by down spray water using flat spray nozzles. The heat transfer surface is made of copper and is 100mm in length and 40mm in width and 15mm in thickness. The experimental condition of spray are as follows: temperatures of the water droplets are T=20~$80^{\circ}C$ and droplets volume fluxes are D=0.001565~0.010438$m^3/m^2s$. Next, correlating equations for the heat transfer characteristics of spray cooling in the high temperature region are developed from the effects of droplets volume flux and the surface temperature of heat transfer plate.