• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.27-33
• /
• 1998

Correlations of drop size and velocity in a spray from the disintegration of liquid jet and liquid film from an internal mixing twin-fluid atomizer, were determined by phase Doppler method. The distribution pattern of Sauter mean diameter(SMD) in a spray was changed by a behavior of liquid flow. As smaller droplets became faster and slower easily by the surrounding conditions, the correlation between drop size and mean velocity was found to be varied as next 3 steps; firstly smaller droplets have a higher mean velocity at the area near atomizer, droplets have almost the same mean velocity and finally larger droplets have a higher mean velocity at the area far from an atomizer.

• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.47-48
• /
• 2001

본 연구의 목적은 폐 구리염화물 용액을 원료로 사용하여 분무열분해 공정에 의해 평균입도가 1㎛이하이며 입도분포가 균일하고 치밀한 조직을 나타내는 미립의 구리산화물 분말을 제조하는데 있다. 또한 본 연구에서는 분무열분해 공정에 의해 생성되는 분말의 특성에 영향을 미치는 반응 온도, 원료용액의 유입속도, 분위기 기체 및 공기의 유입속도, nezzle tip 크기 및 원료용액의 농도 등의 반응인자들의 영향을 검토하였다.

• Journal of Energy Engineering
• /
• v.3 no.1
• /
• pp.54-61
• /
• 1994

계단형태의 고온발생장치로서, 고온의 흐름을 형성하고 난류유동이 없이 일정한 혼합기류를 만들 수 있는 2단격막구조 충격파관 장치를 이용하여, 혼합을 동반하지 않는 분무의 착화과정에 관한 실험을 수행하였다. 본 실험에서는 충격파관 속에 하향으로 설치된 초음파 분무기에 의해 자유낙하 상태에 있는 예혼합 분무주를 만들어서 반사충격파에 의해 순간적으로 단열압축시켜서 착화 현상을 관찰하였다. 고온영역과 저온영역에서 얻어진 활성화에너지는 큰 차이가 나며 본 연구에서 얻은 착화지연의 실험결과는 통상의 분무착화 실험인 전기로법, 급속압축기법, 고온기류속에 연료를 분사하는 방법과 다른 현상을 보였다. 그 대표적인 결과에 대한 예로는 착화지연에 대한 압력 의존성과 연료분사율의 영향이 일반적인 분무의 결과에 비해 적게 나타났다.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.1-7
• /
• 2019

This study was carried out to analyze the spray characteristics as a function of the operating parameters of urea injector used in Urea-SCR system of passenger diesel vehicle. Spray visualization and PDPA experiment were performed to analyze the macroscopic spray development and atomization performance of urea-water-solution. For the urea injector, the deformation of the spray head does not appear to be significant because it operates at a low pressure conditions, and the liquid core and primary droplet are observed throughout the operating conditions. No increase in atomization is seen when the operating pressure is increased, and the spray develops linearly due to poor atomization characteristics. The macroscopic spray behavior of the low-pressure urea injector is predictable through the modification of the Hiroyasu equation.

• Korean Journal of Food Science and Technology
• /
• v.32 no.1
• /
• pp.132-139
• /
• 2000

This study was conducted to optimize the emulsion process and the spray drying process for the microencapsulation of flavor compounds. Using the wall system selected, emulsion process for microencapsulation was optimized on the change of the pressure of piston-type homogenizer. Emulsification pressure of 34.5 MPa was found to be the most suitable for preparing flavor emulsion. Effects of drying temperature and atomizer speed of the spray drier on total oil, surface oil, and flavor release of the flavor powder were investigated using response surface methodology. The optimum spray drying conditions for minimal surface oil and flavor release and maximum total oil were $170{\circ}C$ inlet temperature and 15,000 rpm atomizer speed. The spray-dried powder processed with the highest drying temperature showed spherically-shaped particles with smooth surface.

• Solar Energy
• /
• v.15 no.2
• /
• pp.91-99
• /
• 1995

The influence of deposition parameters on the deposition of $SnO_2$ thin films by spray pyrolysis has been studied. In the case of spray solution with tile concentration of 0.01M, at low deposition temperature the deposition was controlled by surface reaction and portion controlled by mass transfer is increased with increasing deposition temperature to $400^{\circ}C$. Above $400^{\circ}C$, the deposition is controlled by mass transfer at low spray pressure, and by surface reaction at high spray pressure. As the concentration of spray solution increased the deposition rate increased, and in this experiment the deposition depends on the Rideal-Eley mechanism. The deposition rate increased with increasing substrate temperature up to $400^{\circ}C$ and then decreased due to homogeneous nucleation. The thickness of the deposit increased with increasing spray duration, and the adhesion between substrate and deposit was formed physically.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.07a
• /
• pp.22-27
• /
• 1999

최근 정밀농업기술의 중요성이 인식되면서 점살포, 직접살포, 또는 방제목표물의 크기에 따른 분무량 조절 등의 기술이 개발되고 있으나 모든 기술이 분무량 조절에만 치중되어 있다. 일반적인 수압식 노즐의 경우에 분무압을 이용하여 분무량을 제어하면 분무입자의 크기가 적정 이외의 크기로 살포되어 효율적인 방제효과를 얻기가 어렵다. 하나의 제어인자 즉 분무압만을 이용하여 두 가지의 특성 즉 분무량과 분무입자의 크기를 조절하는 것은 이론적으로 불가능하다 정밀방제에 있어 분무입경과 분무량을 독립적으로 조절할 수 있으려면 두 가지 제어인자를 가진 노즐을 이용해야만 가능하며 이러한 범주에 속하는 노즐로는 원심노즐과 이류체노즐, 정전화노즐 등이 있다. (중략)

• Journal of ILASS-Korea
• /
• v.18 no.3
• /
• pp.119-125
• /
• 2013

Digital holographic particle velocity measurement system can be a promising optical tool for the measurements of three dimensional particle velocities. In this research, validation experiments for the digital holographic particle velocity measurement system were conducted with measuring the velocities of glass beads on a rotating disk. Uncertainty analysis was performed to identify the sources of all relevant errors and to evaluate their magnitudes. The measurement results of particle velocities obtained with digital holographic method are compared reasonably well with the known values within acceptable range of errors. Moreover, digital holographic method showed better performance compared with that of optical holographic system.

• Journal of ILASS-Korea
• /
• v.7 no.4
• /
• pp.23-31
• /
• 2002

In this study, the sizes and velocities of droplets in sprays were measured by image processing method from digital images of local region of sprays. The morphological method based on the Euclidean distance transform, Watershed separation, and perimeter image was adopted for the recognition and separation of overlapped particles. The match probability method was used for the particle tracking and pairing. The measurement results show that the present method may be reliable for the analysis of the motion and distribution of droplets produced by spray and atomization devices.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.146-149
• /
• 2006

Spray characteristics of an injector employed in mono-propellant hydrazine thrusters were investigated by PIV(particle image velocimetry) and LDA/PDA(laser/phase Doppler anemometry) techniques. The instanteneous plane image data captured by PIV measurement were examined in order to judge a pass-fail criteria of spray injection performance according to the specific pressure supplied. LDA/PDA technique were also applied to measure the velocity and droplet size of spray were not obtained from PIV measurement. The objective of this experimental study was the clear understanding of spray characteristics as well as the derivation of injector performance to understand clearly the spray characteristics by comparing the both results.