• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.5
• /
• pp.387-395
• /
• 2015

A technique for calculating the additive drag of the inlet in supersonic flow was studied using commercial CFD software, STAR-CCM+, which provides a efficient way of 3 dimensional flow analysis with polyhedron-shaped grid system. Three configurations were chosen and applied to the calculation with various flow conditions of two different free stream Mach No. and some mass flow ratios. Comparisons with results from wind tunnel test gave good agreements. Though computation were carried out with the inviscid and compressible flow around the supersonic inlet for the supercritical condition, ignoring the viscous effects is concluded to give little effects on the accuracy of the additive drag calculation and to make the calculation more efficient owing to less effort and time consumed for grid system build-up and for iteration because of less grid number and simpler boundary condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.381-384
• /
• 2011

Wave drag reduction due to the repetitive laser induced energy deposition over a flat-nosed cylinder is experimentally conducted in this study. Irradiated laser pulses are focused by a convex lens installed in side of the in-draft wind tunnel of Mach 1.94. The maximum frequency of the energy deposition is limited up to 80. Time-averaged drag force is measured using a low friction piston which was backed by a load cell in a cavity as a controlled pressure. Stagnation pressure history, which is measured at the nose of the model, is synchronized with corresponding sequential schlieren images. With cylinder model, amount of drag reduction is linearly increased with input laser power. The power gain only depends upon the pulse energy. A drag reduction about 21% which corresponds to power gain of energy deposition of approximately 10 was obtained.

• Journal of The Korean Society For Urban Railway
• /
• v.6 no.4
• /
• pp.383-392
• /
• 2018

This study investigated the change of additional axial stress of rail and reaction force at bridge bearings due to the track-bridge interaction when laying CWR on non-ballasted railway bridges including truss bridges with relatively long span. According to the results of the present study, additional axial stresses of rail and reaction forces at bridge bearings showed a large increase when CWR is installed on the non-ballasted railway bridge. The additional axial stress of rail can be acceptable if sufficient lateral resistance can be obtained. However, if the reaction force increases, there is a risk of damage of the bearing or pier, and therefore, it is necessary to take measures to mitigate the reaction force. It is found that additional axial stress of rail decreases when considering the frictional resistance of the bridge movable support, but its effect on the bearing reaction force is very small. On the other hand, when the longitudinal track restraint decreases, both additional axial stress of rail and bearing reaction force are reduced to a large extent. Also, when the ZLR fastening devices are applied to the region where the additional axial stress of rail is highest, bearing reaction force as well as additional axial stress of rail greatly decreased. Therefore, the application of ZLR fastening devices with the reduction of the longitudinal track restraints is very effective for installing CWR on non-ballasted railway bridges.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.614-619
• /
• 2015

In this study, a dynamics model was developed to predict the motion performance of an Autonomous Underwater Vehicle (AUV). The dynamics model includes basic dynamic state variables of the hull and force terms to determine the motion of the AUV. The affecting terms for the forces are hydrostatic force, added mass, hydrodynamic damping, lift and drag forces. The force terms can be calculated using analytical and Computational Fluid Dynamics methods. For the underwater motion simulation, a simple PD controller was used. Also, the AUV was tested in a water tank and near sea for the partial verification of the fluid drag force coefficients and way-point tracking motions.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.24-40
• /
• 1997

Horseshoe vortices generated around the juncture between the ship and her appendages often lower a performance of the ship by increasing the appendage drag and making a non-uniform wake on the propeller plane. This paper investigates numerically how the fillet around the juncture of the leading edge influences the juncture flow and the appendage drag. Computation has been made by solving Navier-Stokes equations with MAC method and the flows are at the Reynolds number of 5,000. Five fillets with different height-breath ratios and curvatures are chosen as test models to find out the effects of the shape of fillets on the appendage drag and wake. Computational results show that fillets with a smaller height-breath ratio and/or with a concave curvature has smaller appendage drag and more uniform wake.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2015

An analytical model of liquid sloshing is developed to consider the energy-loss effect through a partially submerged porous baffle in a horizontally oscillating rectangular tank. The nonlinear boundary condition at the porous baffle is derived to accurately capture both the added inertia effects and the energy-loss effects from an equivalent non-linear drag law. Using the eigenfunction expansion method, the horizontal hydrodynamic force (added mass, damping coefficient) on both the wall and baffle induced by the fluid motion is assessed for various combinations of porosity, submergence depth, and the tank's motion amplitude. It is found that a negative value for the added mass and a sharp peak in the damping curve occur near the resonant frequencies. In particular, the hydrodynamic force and free surface amplitude can be largely reduced by installing the proper porous baffle in a tank. The optimal porosity of a porous baffle is near P=0.1.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.488-496
• /
• 1991

Dynamic chanracterisitcs and control of a submerged working robot manipulator have been investigated for articulated type robot manipulator with three revoluted joints. A dynamic equation of the manipulator has been derived. The dynamic equation includes not only mass matrix, centrifugal and Coriolis terms and gravity terms but also added mass, buoyant force and drag force terms, which are important terms for underwater motion description. A series of simulations using computed torque method have been performed for the cases of straight and circular trajectory motion controls. The results of this study show that the dynamic characteristics of the submerged working robot manipulator are very different from that of the manipulator which works in air. The influences of added mass, buoyant force and drag force terms to the total required torques have been discussed as distribution ratios to the total required torques.

• Journal of Power System Engineering
• /
• v.16 no.6
• /
• pp.24-29
• /
• 2012

In this study, the numerical simulation has been performed to investigate the hydrodynamic evaluation between double plate steel rudder and newly designed foil type rudder for small fishing boat. The simulations are carried out in 2 speed ranges with 7 variations of flow's angle of attack which is at intervals of about 5 degree respectively. As the well-known commercial code, FLUENT and CATIA are used as the solver. The simulation results show that new designed foil type rudder is better than conventional double plate rudder in terms of Lift and Drag of running boat in the water.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2011.11a
• /
• pp.37-39
• /
• 2011

예선이 부선을 예인줄로 연결하여 운항할 시 예인줄에 걸리는 장력 및 형상을 예인줄을 다물체로 분할하여 모델링하였다. 이러한 예인줄 요소에 대한 횡동요를 제외한 5자유도 운동방정식을 구성하고, 각 요소들에 작용하는 힘을 정식화하여 연성 운동방정식을 도출하였다. 예인줄 요소들 간에는 예인줄의 재료 특성에 따른 강성을 가진 스프링과 감쇠장치로 연결하여 동력학적 조건을 부가하였고, 요소의 변형을 허용하는 형태로 운동학적 조건은 설정하지 않았다. 예인줄의 다물체 모델링의 검증을 위하여 단순 낙하, 직진, 사인파 형태로 지그재그로 움직이는 예선과 단순 항력체로 가정한 부선의 운동에 대한 시뮬레이션을 수행하였다.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.33-36
• /
• 2012

풍력발전기 성능은 유동의 안정성과 풍속에 의해 결정되는데, 이때 유동 불안정성은 풍력발전기의 성능뿐만 아니라 구조적 문제를 함께 유발시킨다. 본 연구에서는 풍력발전기 타워 후류에서의 불안정성을 최소화시키기 위하여 타워 단면의 기초 형상설계 연구를 수행하였다. 기존의 풍력발전기 타워 형상에 부가 구조물을 설치함으로써 Karman vortex의 생성을 지연시키고 와류 간섭현상을 줄여 풍력발전기의 안정성을 증대시키고자 하였다. 이를 위해 다양한 타워 단면 형상에 대하여 양력계수 및 항력계수를 비교 분석하였다. 그 결과 반지름의 1/2 길이의 자유류 방향 tip과 splitter plate를 후방에 설치하는 것이 후류 불안정성을 억제하는데 가장 효율적인 것으로 나타났다.