• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.2
• /
• pp.35-45
• /
• 1988

In this paper an experimental review of condition monitoring method using time domain vibration signals and statically measured wave forms of a multi-components damaged ball bearing is presented first time. Many investigators studied already about vibration characteristics of a single point damaged ball bearing but they did not make efforts to verify vibration phenomena of a multi-components damaged one. Even in case of a tripple components damaged (i.e, outer race, inner race and rolling element) one, the high frequency resonance technique (HERT) and the displacement time domain technique can be also used for its fault detection. According to experimental results undertaken a static displacement measuring method, the defect locations of components can be proposed confidently with simple calculation of the rotating angles of each component.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.4
• /
• pp.368-373
• /
• 2014

This paper presents the dynamic modeling and analysis results for a spindle supported by angular contact ball bearings (ACBBs) subjected to angular misalignment. Although ACBBs are widely used in spindle systems, their characteristics in regard to angular misalignment have rarely been investigated. A simulation program was developed to calculate the dynamic characteristics of a simple spindle model that is supported by angular contact ball bearings subjected to angular misalignment. Angular misalignment is shown to introduce anisotropy into the angular contact ball bearings and then split the natural frequencies in spindles. Simulations were also performed to show the possibility of evaluating bearing misalignment using natural frequency measurements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.735-743
• /
• 2001

This study was performed to evaluate the dynamic behavior of turbo pump unit. The acceptable separate margin of 1st critical speed was obtained by the use of elastic-ring inserted ball bearing, while the poor separate margin of 1$\^$st/ critical speed was appeared in the case without the elastic-ring. In addition, the results show that the stiffness and damping of plain seals gain more separate margin of 2nd critical speed. However the wear or the failure of seals could reduce the 2$\^$nd/ critical speeds near the operating speed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.341.1-341
• /
• 2002

This paper presents theoretical analysis of the NRRO(the non-repeatable run-out) for a ball bearing with geometric imperfection. The 3DOF dynamic analysis of a ball bearing using the Runge-Kutta method is performed to calculate the displacement of shaft center. Frequency and magnitude characteristics of radial and axial vibrations are investigated. The ball form errors of the ball, the inner race, and the outer race in a HDD spindle ball bearing are precisely measured. (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.10
• /
• pp.805-812
• /
• 2003

This paper presents a method to investigate the characteristics of a ball bearing and the dynamics of a HDD spindle system due to temperature variation. Finite element model is developed for the rotating and stationary parts of a HDD spindle system separately to determine their thermal deformations by using ANSYS, a finite element program. Then, the relative position of the rotating part with respect to the stationary part is determined by solving the equilibrium equation of the contact force between upper and lower ball bearings. The validity of the proposed method is verified by comparing the theoretical natural frequencies of a HDD spindle system with the experimental ones before and after temperature variation. It shows that the elevated temperature results in the increase of contact angle and the decrease of bearing deformation, contact force and bearing stiffness, which result in the decrease of the natural frequencies of a HDD spindle system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1990.10a
• /
• pp.187-191
• /
• 1990

그동안 실험을 통해 측정된 울산화력 BFP 진동 Data의 분석을 통하여 문제 가 되는 과도진동원에 대한 분석이 시도되었다. BFP의 이력과 그간의 측정 자료를 근거로 진동원과 진동에너지의 전달 경로를 가정하였고 각각의 진동 원에 대한 타당성 검토를 위하여 신호처리가 수행되었으며 그 결과로부터 BFP 과도진동 현상에 의해 야기되는 F 베어링 92.5 Hz의 진동에너지는 Voith Coupling의 기어에서 발생되었던 것으로 밝혀졌다. 문제의 해결을 위 해 치차를 대체시켰으며 진동값은 치차가 교환되기 전의 193.$\mu$m이 40.$\mu$m 이하로 줄 수 있었고 따라서 BFP는 안전운행 조건을 만족시키는 동급(Fair Operation)에 들게 됨을 볼 수 있다. BFP로부터 분리된 구동축 Gear는 육안상 크게 균열은 없어 보였으나 특정방향으로 일부 마모가 있어 보였으며 이는 유체와의 회전시 Unbalance에 의한 마모결과로 보여진다. 현 재 6-2 BFP에서 사용되었던 구동측 부품인 기어, Impellar는 치차마모등 비 파괴 정밀조사와 함께 Wet Balancing등의 측정이 진행되고 있다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.326-331
• /
• 2004

The linear motion (LM) guide using ball bearing has many advantages compared with conventional sliding guides. Therefore, LM guide using ball bearing has been used widely to increase the accuracy of the position of a system. This research investigates dynamic characteristics of LM guide through mainly linear analysis. Linear analysis is accomplished by Lagrange equation and finite element method. And another trial that is nonlinear analysis about one mode of LM guide(bouncing mode) from Hertzian contact theory is accomplished in the latter half of this research. Through nonlinear analysis we could observe the softening characteristic due to the Hertzian contact nonlinearity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.3
• /
• pp.29-42
• /
• 1988

With the Hertzian contact theory, it is possible to determine the bearing load distributing pattern among the balls and rollers and also variations of the load-displacement relationships for rolling elements contacting raceways according to bearing clearance, load distribution, contact forces and dimensions of bearing components (i.e diameter of raceway and rolling elements), etc. In this paper the calculation theories of contact load and normal approach between two raceways under radial load are reviewed, and compared these calculation results with those of experimental results. A new calculation theory for elastic displacement of outer-race of ball bearing under radial load is developed by authors by application of energy method, which is independent on the effects of roughness, bending or eccentricity of bearing with driving shaft, and is effective in measuring the location of its defect.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.326-333
• /
• 2004

This paper presents the structural characteristics analysis of a high-speed horizontal machining center with spindle speed of 50, 000rpm and feedrate of 120m/min. The spindle system is designed based on the built-in motor, angular contact ceramic ball bearings, oil-air lubrication and oil-jacket cooling method. The X-axis and Y-axis feeding systems are composed of the linear motor and linear motion guides, and the Z-axis feeding system is composed of the servo-motor, ball screw and linear motion guide. The structural analysis model of the high-speed horizontal machining center is constructed by the finite element method, and the validity of structural design is estimated based on the structural deformation of the high-speed horizontal machining center and spindle nose caused by the gravity and inertia forces.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.2 s.11
• /
• pp.22-28
• /
• 2001

This study was performed to evaluate the dynamic behavior of turbo pump unit. The acceptable separate margin of $1^{st}$ critical speed was obtained by the use of elastic-ring inserted ball bearing, while the poor separate margin of $1^{\st}$ critical speed was appeared in the case without the elastic-ring. In addition, the results show that the stiffness and damping of plain seals give more separate margin of $2^{nd}$ critical speed. However the wear or the failure of seals could reduce the $2^{nd}$ critical speed near the operating speed.