• Membrane Journal
• /
• v.16 no.2
• /
• pp.85-105
• /
• 2006

Poly(lactic acid) is a linear aliphatic thermoplastic polyester, produced by the ring-opening polymerization of lactides and the lactic acid monomers, which are obtained from the fermentation of sugar feed stocks, corn, etc. PLA has high mechanical, thermal plasticity, fabric-ability, and biocompatibility, So PLA is a promising polymer far various end-use applications. In recent time, the intercalation of polymers from either solution or the melt in the silicate galleries of clay is the best technique to prepare nanocompoiste material which often exhibit remarkable improvement of mechanical, thermal, optical and physicochemical properties when compared with the pure polymer or conventional composites. Layered silicate is naturally abundant, economic, and more importantly benign to the environment.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.4
• /
• pp.23-37
• /
• 2005

The factors affecting the long-term design strength of geogrid can be classified into factors on creep deformation, installation damage, temperature, chemical degradation and biological degradation. Especially, creep deformation and installation damage are considered as main factors to determine the long-term design strength of geogrid. Current practice in the design of a reinforced soil structures is to calculate the long-term design strength of a geosynthetic reinforcement damaged during installation by multiplying the two partial safety factors, $RF_{ID}$ and $RF_{CR}$. This method assumes that there is no evaluation of synergy effect between installation damage and creep deformation of geogrids. This paper describes the results of a series of experimental study, which are carried out to assess the combined effect of the installation damage and the creep deformation for the long-term design strength of geogrid reinforcements. A series of field tests was carried out to assess installation damage of various geogrids with respect to different fill materials, and then creep tests are conducted to evaluate the creep deformation of both undamaged and damaged geogrids. The results indicated that the tensile strength reduction factors, RF, considering the combined effect between the installation damage and the creep deformation is less than that calculated by the current design method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.565-568
• /
• 2008

Domestic area of most be happened chloride deicer damage. Because daily mean temperature is below 0$^{\circ}C$ from the area of domestic most. Concrete durability influence Air Content. Presently, We used to AE(air-entraining agent) for increase freeze-thaw durability. So, on concrete Air Spacing ratio used $200{\mu}m{\sim}230{\mu}m$ in Canada and under $250{\mu}m$ in Japan institution. Use of Air content has been and will continue to be a major part of concrete durability and scaling. Chloride-containing chemicals such as calcium chloride or rock salt are main deicers for the road. The prepared optimum mix concrete in this study show that freeze-thaw and scaling resistance of Non-AE(air content 1.5%) and AE (air content 4.5%, 7.2%). Solution concentrations of deicing agent were good result, and the pore system and change of hydration products is not difference comparing before freeze-thaw test.

• Journal of Korean Society of Forest Science
• /
• v.103 no.2
• /
• pp.233-239
• /
• 2014

This study was carried out to propose the criteria for the prediction of landslide occurrence through analysis the influence of each factor by using the quantification theory. The results obtained from this study are summarized as follows. From a stepwise regression analysis between the landslide area($m^2$) and environmental factors, the factors strongly affecting the landslide sediment($m^2$) were the Parents rock (igneous), cross slope(complex), coniferous forests (forest type) and slope gradient ($21{\sim}30^{\circ}$). According to the range, it was shown in order of Cross slope (0.2922), Parents rock (0.2691), Forest type (0.2631) and Slope gradient (0.2312). The range of prediction score of landslide occurrence has been distributed between score 0 and score 1.0556, the median value was score 0.5278. The prediction for class I was over 0.7818, for class II was 0.5279 to 0.7917, for class III 0.2694 to 0.5278 and for class IV was below 0.2693. The prediction on landslide occurrence appeared relatively high accuracy rate as 72% for class I and II. Therefore, this score table for landslide will be very useful for judgement of dangerous slope.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.833-841
• /
• 2013

In the case of composite material, a variety of characteristics were expressed depending on the materials that were composed of. In this study, the materials showing non-linear shear behavior were investigated among FRP composite. Each specimen was designed and analyzed according to ASTM D4255 method: regulations on the 2-rail. The dependent variables included in this experiment were a variety of fiber, fiber volume ratio, fiber array direction, temperature, material homogeneity. For determination of characteristics based on the fiber array, fiber array direction of 0, 30, 45, and 60 degrees were selected for test specimen. Temperature of 25, 40, 60, and $80^{\circ}C$ were considered for investigation of FRP materials'shear behavior based on the external temperature. Nonlinear shear behavior was observed throughout the FRP composite material in this study. Also, using vinyl ester resins, high fiber volume ratio, and fiber array direction of 45 degree appeared to show the most prominent nonlinear shear behavior. As for the findings related to the temperature change, non-linear behavior was decreased as the external temperature increased. For factory manufactured product, non-linear behavior was relatively at parity in comparison to the behavior found in the hand lay-up FRP composite specimen.

• Korean Journal of Environmental Biology
• /
• v.20 no.3
• /
• pp.256-262
• /
• 2002

This research investigated experimentally on the population growth in the aquatic microcosm with the wastewater of plating factory. The purpose of this study was to evaluate the effect of culture conditions of the characteristic growth pattern of the examined species. Population of the system is consists of three organisms; Chlorella vulgaris as a producer, Cyclidium glaucoma as a consumer and Pseudomonas putida as a decomposer. The different growth patterns of each population are followed by surfactant type; Especially C. glaucoma was sensitive, Ch. uvlgaris was maintained population size stably even at high level of surfactant and p. putida was not significantly affected. After treatment of waste water from plating factory, it began to be affected at 1.0% solution treatment to Ch. vulgaris which the cell number was decreased prominently after 2 days, and C. glaucoma was disappeared at 2.5% solution treatment. P. putida was showed increasing pattern according to treatment concentration, at 2.5% solution and population size grew double. The result from current microcosm study indicates that this model system can be applied to environmental assessment method for various pollutants.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.239-249
• /
• 2011

The behavior of the fiber reinforced concrete (FRC) base under environmental loads was analyzed numerically as a fundamental study to develop a high structural and functional performance composite pavement system in which the base was formed using FRC and the asphalt or cement concrete surface was placed on it. A two-dimensional finite element model of the FRC base was developed and the sensitivity study was performed with the variables including slab thickness of base, thermal expansion coefficient, elastic modulus, and tensile and compressive strengths. The crack spacing and crack width were selected as representatives of the base behavior. The effects of the selected variables on the crack spacing and crack width were analyzed and the sensitive variables were determined. The results of this study could be useful to determine the optimal material properties of the FRC base for combining well with the surface materials.

• Korean Journal of Food Science and Technology
• /
• v.35 no.5
• /
• pp.877-883
• /
• 2003

Multi-degradable master hatch (M/B) was prepared and 0.05 mm polyethylene (PP) food packaging films containing 0, 10, and 20% M/B were manufactured by inflation film processing. The films were exposed to UV radiation, fungi, and heat in order to observe their photolysis, biodegradability, and thermal degradability, respectively. While pure PP film maintained more than 70% of its original elongation after 8 weeks of UV radiation, an almost perfect loss in the elongation of PP film containing 20% M/B was observed. Significant decreases in elongation of PP films by heat treatment $(68{\pm}2^{\circ}C)$ were also found in samples containing the multi-degradable M/B. By observing changes in film surface after the inoculation of fungi using scanning electron microscopy (SEM), the biodegradability of plastic film could be accelerated with the addition of multi-degradable M/B. The results of the mulching test in yard showed that adding multi-degradable M/B can effectively degrade plastic films in natural environmental conditions without interrupting the growth of plants.

• Journal of Animal Environmental Science
• /
• v.18 no.2
• /
• pp.99-110
• /
• 2012

The purpose of the study is to collect basis data for to establish standard administrative processes of liquid fertilizer treatment. From this survey we could make out the key point of each step through a case of effective liquid manure treatment system in pig house. It is divided into six step; 1. piggery slurry management step, 2. Solid-liquid separation step, 3. liquid fertilizer treatment (aeration) step, 4. liquid fertilizer treatment (microorganism, recirculation and internal return) step, 5. liquid fertilizer treatment (completion) step, 6. land application step. From now on, standardization process of liquid manure treatment technologies need to be develop based on the six steps process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.138-142
• /
• 2018

This study used HILS to test an expansion joint, which is vulnerable to the water hammer effect. The operation data for the HIL simulator was the length rate of the expansion joint by the water hammer, which was used for life prediction based on the vibration durability. For the vibration durability test, the internal pressure of the expansion joint was assumed to be a factor of the durability life, and the lifetime prediction model equation was obtained by curve fitting the lifetime data at each pressure. During the test, the major failure modes of crack and water leakage occurred on the surface of the bellows part. The lifetime prediction model typically follows an inverse power law model. The pressure is a stress factor, and the model is effective in only a specific environment. Therefore, another stress factor such as temperature will be added and considered for a mixed lifetime prediction model in the future.