• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.994-1000
• /
• 2001

With the development of electromagnetic communication technology and increased use of electromagnetic wave, the countermeasure of EMI(Electromagnetic Interference) becomes more important socially, and interest for the electromagnetic wave absorber has also increased. In this paper, we have studied characteristics of frequency dependency on complex permittivity and complex permeability according to the changes of composition rate and sintering temperature of NiCuZn ferrite also known as electromagnetic wave absorber and further looked into effect of electromagnetic wave absorption properties. From the measurement where the composition of $Fe_2O_3$ and ZnO of NiCuZn ferrite was fixed at 49 and 34 mol% respectively while composition of NiO and CuO has been varied at each test, we found out that Initial permeability and permittivity were high and the absorbing ability of electromagnetic wave recorded best with $loss tangent(=\mur"/\mur')$ displays more than 1 within the frequency band of 2MHz~9.5MHz when the composition ratio of NiO was ranged around 8.5~9.5 mol% and the sintering temperature was $1080^{\circ}C$.TEX>.

• Journal of the Korean Magnetics Society
• /
• v.18 no.3
• /
• pp.115-119
• /
• 2008

The raw materials of permalloy were processed the ball-mill for 30 hours and the shape of permalloy particles was changed from sphere to flake type, which was observed using scanning electron microscope. The complex permittivity and permeability spectra and reflection loss of permalloy-rubber composite was measured using Network Analyzer in order to investigate the relationship between the microwave absorption and the material constants. The flake type permalloy-rubber composite showed high reflection loss, which was due to the high complex permittivity and permeability. Also, the matching frequency shifted toward lower frequency range with microwave absorber thickness, and the maximum reflection loss of -6.1 dB was observed in $1.65\;GHz{\sim}1.86\;GHz$ for a 1.3 mm thickness.

• Composites Research
• /
• v.21 no.5
• /
• pp.9-14
• /
• 2008

Carbon nanofibers (CNFs) were used as dielectric lossy materials and NiFe particles were used as magnetic lossy materials. Total twelve specimens for the three types such as dielectric, magnetic and mixed radar absorbing materials (RAMs) were fabricated. Their complex permittivities and permeabilities in the range of $2{\sim}18$ GHz were measured using the transmission line technique. The parametric studios for reflection loss characteristics of each specimen to design the single-layered RAMs were performed. The mixed RAMs generally showed the improved absorbing characteristics with thinner matching thickness. One of the mixed RAMs, MD3with the thickness of 2.00 mm had the 10 dB absorbing bandwidth of 4.0 GHz in the X-band ($8.2{\sim}12.4$ GHz). It also showed very broad 10 dB absorbing bandwidth as wide as 6.0 GHz in the Ku-band ($12.0{\sim}18.0$ GHz) with the thickness tuning to 1.49 mm. The experimental results for selected several specimens were in very good agreements with simulation ones in terms of the overall reflection loss characteristics and 10 dB absorbing bandwidth.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.10
• /
• pp.1141-1149
• /
• 1988

The inverse scattering scheme, which was exploited for the reconstruction of complex permittivity profiles of 2-dimensional dielectric objects by using the moment method in the spatial domain, is modified to be applicable in the spectral domain. The presented scheme is conceptually simple and provides some proper ways to regularize the ill-posed characteristics inherent to the inverse scattering problems.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.4
• /
• pp.528-536
• /
• 1999

This work studies the effects of transient reflectance on the thermal responses of a metal(gold) thin-film during ultrashort laser heating. The heating process is calculated using the conventional conduction model (parabolic one-step: POS), parabolic two-step model (PTS) with and without variable properties, hyperbolic two-step model (HTS). Results from the HTS model are very similar to those from the PTS model, since the laser heating time in this study is greater than the electron relaxation time. PTS model with variable properties, however, results in totally different temperature profiles compared to those from POS models or calculation with constant properties. Transient reflectances are estimated from electron temperature distributions and based on the linear relationship between the electron temperature and complex dielectric constants. Reflectance of the front surface can be changed with respect to dielectric constants, while those of the rear surface remain unchanged.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.947-951
• /
• 1995

The electromagnetic interference is prevented by the high magnetic loss of the ferrite. The absorbing property of electromagnetic wave could be improved by the ferrite that has a finer and more uniform microstructure. The thermal decomposition of organic acid salt provided the uniform composition and fine powder. The absorbing properties of electromagnetic wave were evaluated by the relative complex permeability, permittivity, and the attenuation which is calculated from the results of network analyzer. The permeability and permittivity were increased with increase of the density and with decrease of the grain size. The matching thickness could be reduced with increasing sintered temperature. The attenuation of the Cu-Ni-Zn ferrite showed over 20dB when the matching thickness and the matching frequency range were 6.75mm and from 160MHz to 640MHz, respectively.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.2
• /
• pp.11-19
• /
• 1999

The design procedure as well as some test results of a low-cost commercial radome for mobile DBS(Direct Broadcasting Satellite) receiving antenna system are presented in this paper. At first the complex permittivity of dielectric material should be measured in order to select a material for radome design. The complex permittivities of low-cost plastics supplied by domestic vendors are measured and presented. And then the transmission losses of the sheets are calculated. The calculated results are verified by the measurements of wave transmission test of that sheets. Two kinds of radomes, ABS single-layer and A-Sandwich((PET-Foam-ABS), are fabricated and measured practically. The transmission losses of single-layer and A-sandwich radome are 1.5dB and 0.6dB respectively at the maximum wave incident angle of 57 degree. Also the calculated crosspolarization caused by A-sandwich radome is under 20dB.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.268-274
• /
• 2013

In this paper, objective functions are defined for optimization of radar absorbing structures (RAS) on the aircraft wing leading edge. RAS is regarded as a single layer structure made of dielectrics. Design variables are the real and imaginary parts of complex permittivity. Reflection coefficient(RC) and radar cross section(RCS) are used in the objective function respectively. Transmission line theory is employed to calculate the RC. The RCS is evaluated by using physical optics(PO) for a leading edge part model. Genetic algorithm(GA) is used to perform optimization procedures. The radar absorbing performance of designed RAS is assessed by the RCS of a wing which has RAS on the leading edge.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.42-50
• /
• 2023

In this study, hexagonal ferrite powder with chemical formula SrZn_2-xCo_xFe₁₆O₂₇ was synthesized by a solid-state reaction method and its electromagnetic (EM) wave absorption characteristics were evaluated in the frequency range of 0.1-18 GHz with absorber thickness range of 0 - 10 mm. Reflection loss (RL) affecting electromagnetic wave absorption performance was calculated based on the transmission line theory using measured complex permeabilities and permittivities. RL spectra were also directly measured for some samples. They were well matched with calculated results. High-frequency complex permeability characteristics were changed gradually according to the amount of Co substitution (x). The EM wave absorption frequency band could be tuned accordingly. Hexaferrite samples with x = 1.0, 1.25, and 1.5 exhibited remarkable maximum electromagnetic wave absorption performances with minimum RL (RL_min) lowered than -50 dB. They also showed a very broad frequency band (Δf > 10 GHz) in which more than 90% of the EM wave energy absorption occurred (RL ≤ -10 dB).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.1051-1057
• /
• 2008

In this paper, we analyzed the characteristics of the EM wave absorber which was fabricated by using flake sendust (soft metal magnetic powder). The flake sendust was made of 3 different granularity by attrition mill. First, we have fabricated 3 kind of EM wave absorbers using the flake sendust and CPE(Chlorinated Polyethylene) and measured the S-parameters of the EM wave absorber. The complex relative permittivity and permeability were calculated from the measured data and the variations according to a change of granularity were researched. As a result, it was confirmed that the EM wave absorber using flake sendust with the $140{\mu}m$ average granularity has outstanding absorption ability in high frequency range(C band) for the reduction of eddy current loss(increase of permeability) and the increase of space charge polarization(increase of permittivity).