• 한국가시화정보학회지
• /
• 제9권3호
• /
• pp.59-64
• /
• 2011

In this study the change of free surface vortex is expressed through the time volume fraction using multiphase unsteady condition in sump, because in previous studies of the pump sump did not represent the behavior of the free surface vortex exactly due to the reason it was calculated using single phase and steady condition. The reliability of the computational analysis is verified through comparing experimental results with that of present numerical analysis. Homogeneous free surface model is used to apply interactions of air and water. The results show that the free surface vortex can be identified on the isotropic surface at air volume fraction 1%~5%. The vortices make an air column from the free surface to the sump intake and are created and destroyed repeatedly. The behavior of free surface vortex at numerical analysis is quite similar to experimental test. The result of vortex motion according to time, works on a cycle.

• 대한기계학회논문집B
• /
• 제20권3호
• /
• pp.1061-1073
• /
• 1996

Vortex tube is a simple device which splits a compressed gas stream into a cold stream and a hot stream without any chemical reactions. The phenomena of energy separation taking place in a vortex tube has been investigated experimentally. Recently, vortex tube is widely used to local cooler of industrial equipments and air conditioner of special purpose. In this study, experimental study on vortex tube efficiency was performed with various cold end orifices and nozzles type. The experimental results indicate that there is an optimum diameter of cold end orifice and nozzle type for the best cooling performance. The variation of the maximum wall temperature along the vortex tube surface provides useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. The similarity relation for the prediction of the temperature of the cold exit air was obtained.

• 설비공학논문집
• /
• 제13권11호
• /
• pp.1149-1155
• /
• 2001

The experimental investigation on energy separation in a vortex tube has been carried out to sow the effect of inlet and outlet pressures with various working fluids(air,$O_2,\;and\; CO_2$). Those outlet pressure means cold outlet and hot outlet pressure which were set equally. The results showed that the total enthalpy variation became a maximum when the mass flow rate at the cold outlet was a half of the total mass flow rate in the vortex tube (y=0.5). The total enthalpy variation was quite affected by the pressure difference between the inlet and outlet of vortex tube when the ratio of the inlet pressure to the cold outlet pressure remained constant. Although specific enthalpy differences between the inlet and the outlet (both cold and hot outlet) did not noticeably vary with the pressure difference, the specific enthalpy difference between the inlet and cold outlet was dominantly affected by physical properties of working gases.

• 대한환경공학회지
• /
• 제31권11호
• /
• pp.1033-1040
• /
• 2009

고효율 싸이클론의 설계는 압력강하의 최소화와 집진효율의 최대화를 이루는 것이 중요하다. 본 연구는 고온, 고압 조건하에서 신뢰성 있는 컴퓨터 프로그램을 개발하여 싸이클론의 집진효율에 영향을 주는 물리적 메카니즘을 연구하는 것이다. 수치 해석적 연구를 통한 고온, 고압 조건에서의 압력강하 계산은 실험데이터와 비교적 잘 일치하였다. 온도와 압력은 일반적으로 집진효율에 중요한 영향을 미치는데 보통 항력에서 가스의 밀도나 점도 등에 영향을 주어서로 상반되는 결과를 나타낸다. 그러므로 고온 운전에 따른 집진효율의 감소는 고압 조건으로 운전하는 것이 대안이 될 것으로 판단된다. 집진효율에 영향을 주는 인자에 대해 좀 더 세부적인 연구를 위하여 접선방향 속도나 보텍스 파인더의 직경 등과 같은 싸이클론의 설계변수나 운전변수에 따른 연구를 수행하였다. 예상한 바와 같이 접선방향의 속도가 집진효율에 가장 큰 영향을 주었다. 그리고 보텍스 파인더의 직경이 증가할수록 집진효율은 감소하였으며 보텍스 파인더의 길이는 집진효율에 큰 영향을 나타내지 않았다.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1805-1812
• /
• 1993

Two-dimensional spin-up in a rectangular domain is analysed by the numerical computation of the Navier-Stokes equations. The cells are in most cases generated by the vorticity developed near the uper and lower surfaces. Moreover, the movement and interaction of those vortices play a key role in establishing the quasi-steady state. The critical phenomena observed in the previous experiment turns out to be caused by the critical movement of the vortices.

• 대한조선학회논문집
• /
• 제51권3호
• /
• pp.259-264
• /
• 2014

Tip vortex cavitation (TVC) is important for naval ships and research vessels that require raising the cavitation inception speed to maximum possible values. The concepts for alleviating the tip vortex are summarized by Platzer and Souders (1979), who carried out a thorough literature survey. Active control of TVC involves the injection of a polymer or water from the blade tip. The main effect of such mass injection (both water and polymer solutions) into the vortex core is an increase in the core radius, consequently delaying TVC inception. However, the location of the injection port needs to be selected with great care in order to ensure that the mass injection is effective in delaying TVC inception. In the present study, we propose a semi-active control scheme that is achieved by attaching a thread at the propeller tip. The main idea of a semi-active control is that because of its flexibility, the attached thread can be sucked into the low-pressure region closer to the vortex core center. An experimental study using a scale model was carried out in the cavitation tunnel at the Seoul National University. It was found that a flexible thread can effectively suppress the occurrence of TVC under the design condition for a model propeller.

• 대한의용생체공학회:의공학회지
• /
• 제23권6호
• /
• pp.437-449
• /
• 2002

관상동맥은 체순환 동맥과 비교하여 매우 다른 유동조건을 갖는다. 본 연구에서는 이러한 관상동맥의 유동조건이 다른 혈관과 비교하여 동맥경화의 생성과 발전에 어떤 영향을 미치는지를 협착된 혈관 모델의 혈류역학적 전산유체해석을 통해 분석하였다. 연구 결과, 협착된 관상동맥 모델의 유동장과 벽면전단응력의 분포는 복부 대동맥 및 고동맥과 비교하여 큰 차이점을 보였다. 관상동맥은 혈관 지름이 혈류량에 비해 상대적으로 작으므로 큰 벽면전단응력값을 보이는 반면에, 혈관 협착부 목 후방부에 하나의 보텍스만 보이는 단순한 유동장 분포를 보였다. 한편, 복부대동맥과 고동맥 모델은 협착부 목 전반부와 후방부에 여러 개의 보텍스를 나타내는 복잡한 유동장을 형성하였다. 관상동맥 모델에서는 임피던스 페이즈앵글이 음의 큰 값을 가질 때에 벽면전단응력의 크기가 증가하고 재순환영역이 증가함이 관찰되었다. 그러므로 심장의 수축운동과 -110。에 이르는 관상동맥의 큰 음의 임피던스 페이즈앵글 값은 동맥경화를 촉진시키는 유동환경을 조성함을 알 수 있었다.

• 한국유체기계학회 논문집
• /
• 제15권5호
• /
• pp.60-66
• /
• 2012

One of commonly physical phenomena encountered in pump sump systems in which its significant influence to the hydraulic performance of pump system plays an important role in the field of fluid engineering, is the appearance of free surface and submerged vortices. In this paper, a study of the vortices behavior and their formative mechanism of asymmetry is considered in this paper by using numerical approach. The Reynolds-Averaged Navier-Stokes (RANS) equations and k-omega Shear Stress Transport turbulence model used to describe the properties of turbulent flows, in company with VOF multiphase model, are implemented by Fluent code with multi-block structured grid system. In the numerical simulation, the calculated elevation of air-water interface and vortex core contours are used to classify visually surface vortices as well as submerged vortices. It is shown that the free surface vortex is identified by the concavity of liquid region from the free surface and swirling flow at that own plane. To investigate the distinctive behavior of these vortices corresponding to each given flow rate at the same water level, some numerical testing of them are considered here in such a manner that the flow pattern of surface vortex are obtained similarly to the obtained results from experiment. Furthermore, the influence due to the change of grid refinement and the variation of depth of the concavity are also considered in this paper. From that, these influential factors will be implemented to design a good pump sump with higher performance in the future.

• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1350-1362
• /
• 1997

An experimental study has been performed on vortex pairing under fundamental and subharmonic forcing with controlled initial phase differences through hot-wire measurements and a multi-smoke wire flow visualization. For the range of St$_{D}$ < 0.6, vortex pairing was controlled by means of fundamental and subharmonic forcing with varying initial phase differences. Much larger mixing rate was achieved by two-frequency forcing with a proper phase difference than one frequency forcing. As St$_{D}$ decreased, vortex pairing was limited to a narrow region of the initial phase difference between two disturbances and higher amplitudes of the fundamental and its subharmonic at the nozzle exit were required for more stable pairing. As the amplitude of the subharmonic at the nozzle exit increased for fixed St$_{D}$ and fundamental amplitude, the distribution of the subharmonic mode against the variation of the initial phase difference changed from a sine function form into a cusp-like form. Thus, vortex pairing can be controlled more precisely for the former case. For St$_{D}$ > 0.6, non-pairing advection of vortices due to the improper phase difference was sometimes observed in several fundamental forcing amplitudes when only the fundamental was applied. However, when its subharmonic was added, vortex pairing readily occurred. As the initial amplitude of this subharmonic increased, the position of vortex pairing moved upstream. This was thought to be due to the fact that the variation of the initial phase difference between the fundamental and its subharmonic has less effects on vortex pairing in the region of fundamental-only vortex pairing.pairing.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.607-612
• /
• 2001

Based on the flow characteristics around a piercing cylinder, a free surface-flow velocitmetry which can be used in extremely harsh environment such as molten steel flow was developed. The velocimetry is consisted of finite length cylinder, load detecting elastic plate, electric signal transducer and data acquisition H/W and S/W. Using such a velocimetry, two velocity measurement schemes were established which one is flow resistance detecting scheme and the other is Karman Vortex frequency detecting scheme. For calibration of each scheme, realistic flow water model was used and in followings, detailed calibration processes were explained.