• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.107-116
• /
• 2020

The compaction grouting technique is widely used to improve the liquefaction resistance of loose sands that are liquefaction-prone. Particularly, the horizontal injection of compaction grout is proposed for the liquefiable ground with an overlying structure as it does not allow the vertical compaction grouting. However, there has been limited number of researches on the horizontal compaction grouting. Therefore, this study explores the grout bulb shape and expansion direction in loose sand. A series of scaled two-dimensional experiments on the horizontal compaction grouting was conducted varying the overburden stress. The results show that the grout bulb grows in an elliptical shape though its directivity of major axis changes with the overburden effective stress and relative density. The grout bulb expands faster in a horizontal direction under a low overburden stress with a small relative density. The higher overburden stress and the greater relative density cause the more circular shape with the faster expansion in a vertical direction. The presented finding is expected to contribute to accurate and efficient design of the horizontal compaction grouting method.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.6
• /
• pp.27-40
• /
• 2006

Damage of cut-and-cover tunnel lining can be attributed to physical and mechanical factors. Physical factors include material property, reinforcement corrosion, etc. while mechanical factors include underground water pressure, vehicle loads, etc. This study is limited to the modeling of rigid circular cut and cover tunnel constructed at a depth of $1.0{\sim}1.5D$ in loose sandy ground and subjected to a vibration frequency of 100 Hz. In this study, only damages due to mechanical factors in the form of additional loads were considered. Among the different types of additional, excessive earth pressure acting on the cut-and-cover tunnel lining is considered as one of the major factors that induce deformation and damage of tunnels after the construction is completed. Excessive earth pressure may be attributed to insufficient compaction, consolidation due to self-weight of backfill soil, precipitation and vibration caused by traffic. Laboratory tunnel model tests were performed in order to determine the earth pressure acting on the tunnel lining and to investigate the applicability of existing earth pressure formulas. Based on the difference in the monitored and computed earth pressure, a factor of safety was recommended. Soil deformation mechanism around the tunnel was also presented using the picture analysis method.

• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.519-533
• /
• 2023

In this study, the linear cutting tests of pick cutters were carried out on a granitic rock with the average compressive strength over 100 MPa. From the tests, the correlation between the cutter acting force and the temperature measured by infrared thermal imaging camera during rock cutting was analyzed. In every experimental condition, the maximum temperature was measured at the rock surface where the chipping occurred, and the temperature generated in the rock was closely correlated with the cutter acting force. On the other hand, the temperature of a pick cutter increased up to only 36℃ above the ambient temperature, and the correlation with the cutter force was not obvious. This can be attributed to the short cutting distance under laboratory conditions and the high thermal conductivity of the tungsten carbide inserts. However, the relatively high temperature of the tungsten carbide inserts was found to be maintained. Therefore, it is recommended that a reinforcement between the insert and the head of a pick cutter or the quality improvement of silvering brazing in the production of a cutter is necessary to maintain the high cutting performance of a pick cutter.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.12
• /
• pp.93-102
• /
• 2023

Despite recent modifications to building structural standards emphasizing the seismic stability of building foundations, the current design focus remains solely on vertical support, resulting in insufficient consideration of horizontal loads during earthquakes. In this study, we evaluated the dynamic behavior of inclined tripod micropiles (ITMP), which provide additional seismic resistance against horizontal and vertical loads during earthquakes. A comparison of the dynamic characteristics, such as acceleration, displacement, bending moment, and axial force, of ITMP with a 15° installation angle and normal vertical micropiles with a 0° installation angle was performed using dynamic centrifuge model tests. Results show that under moderate seismic loads, the proposed ITMP exhibited lower acceleration responses than the vertical micropiles. However, when subjected to a long-period strong seismic excitation, such as sine (2 Hz), ITMP showed greater responses than the vertical micropiles in terms of acceleration and settlement. These results indicate that the use of ITMP reduces the amplif ication of short-period (high-f requency) contents compared with the use of vertical micropiles. Therefore, ITMP can be used to enhance seismic performance of structures.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.177-184
• /
• 2003

매립장 내의 설치된 중간 복토층(intermediate cover)은 매립 도중 혹은 매립완료 후 종종 침출수가 하부의 침출수 집배수관으로 이동하는 것을 막아 매립장 내에 일정 침출수위를 형성시킨다. 이렇듯 중간 복토층은 침출수의 원활한 순환을 막아 매립장 바닥에 형성되어야 하는 침출수위가 중간복토층 위에 형성되도록 하는데, 이는 매립장의 구조적 안정성을 깨뜨리고 주변으로 침출수 누출을 유발시키게 된다. 본 연구에서는 이처럼 중간복토층 상부에 형성된 침출수위를 저하시키기 위하여, 폐기물 매립시 중간복토층에 투수성이 뛰어나고 역학적 강도와 화학적 내구성을 갖는 배수파일(Drain Pile)을 설치할 것을 제안하였다. 배수파일은 중간복토층 상부에 형성될 수 있는 침출수를 매립장 바닥으로 배수시키고, 침출수 집배수정으로 이송이 가능하게 만든다. 또한 배수파일은 매립장 내부에 설치됨으로써 폐기물의 자체 강성을 증가시키고, 동시에 매립장의 측방유동을 막아 구조적 안정성을 확보하는 효과도 기대할 수 있다. 실내시험을 통해 배수파일 충진재로서 굴패각의 활용가능성을 확인한 결과, 산업 폐기물인 굴패각이 침출수의 pH를 중화시키고 유해물질인 NH$_{4}$$^{+}$를 제거하는데 효과적임을 확인할 수 있었다. 한편, 실제현장의 침출수흐름을 모사하기 위해 범용 프로그램(SEEP/W)을 이용하여 매립지 내에서 배수 파일의 효과를 확인하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.65-81
• /
• 2003

During the last few decades in Korea, the development of hillside or mountain areas has rapidly increased for infrastructure construction such as railroads, highways and housing. Many landslides have occurred during these constructions. Also, the amount and scale of damage caused by landslides have increased every year. In the case of Far East Asia including Korea, the damage of landslides is consequently reported during the wet season. In this paper, the effect of stabilizing piles on slope stability is checked and the behavior of slope soil and piles are observed throughout the year by field measurements in the large-scale cut slopes. In particular a large-scale cut slope situated on the construction site for the express highway in Donghae, Korea. First of all, The behavior of the slope soil was measured by inclinometers during slope modification. Landslides occurred in this area due to the soil cutting for slope modification. The horizontal deformations of slope soil gradually increased and rapidly decreased at depth of sliding surface indicating that the depth of sliding surface below the ground surface can be predicted. On the basis of being able to predict the depth of the sliding surface, stabilizing piles were designed and constructed in this slope. To ensure the stability of the reinforced slope using stabilizing piles, an instrumentation system was installed. The maximum deflection of piles is measured at the pile head and it is noted that the piles deform like deflection on a cantilever beam. The maximum bending stress of piles is measured at the soil layer. The pile above the soil layer is subjected to lateral earth pressure due to driving force of the slope, while pile below soil layer is subjected to subgrade reaction against pile deflection. As a result of research, the effect and applicability of stabilizing piles in large-scale cut slopes could be confirmed sufficiently.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.2
• /
• pp.39-45
• /
• 2004

Geocomposite mechanically bonded with woven type geotextile and nonwoven geotextile was used to examine to the long-term creep deformation behaviors by the SIM(Stepped Isothermal Method). The temperature steps were $26^{\circ}C$, $40^{\circ}C$, $54^{\circ}C$, $68^{\circ}C$, $82^{\circ}C$ and loading levels were 40%, 50%, 60% of designed strength for stepped isothermal method. Results of creep tests are showing that their strain were lower than 10% during 10,000 hours(GRI GS 10). Also, the effect of weft injection density to the creep deformation behaviors were examined. The weft densities of 0%, 50%, 100% of the original weft density showed the creep strain within 10% and the creep strain was increased with the decrease of weft injection density.

• Journal of the Korean Geosynthetics Society
• /
• v.7 no.2
• /
• pp.31-39
• /
• 2008

The information of cut slope in Baekyang Mt. area, Busan is investigated in order to construct the Slope Management System in Urban Area. The slope inspection sheet is made to record the characteristics for cut slopes, and that is capable to be inputted slope information systematically. The cut slopes in Baekyang Mt. area are consisting of 103 slopes. Most of the cut slopes are constructed in cutting slope and retaining wall (CR). The school is mostly distributed adjacent to cut slopes. The average traverse of cut slopes is approximately 122m, and the average height is approximately 18m. The slopes combined with soil and rock are mostly distributed. The retaining wall was installed in the toe part of cut slope in order to increase the slope stability, and the additional reinforcement methods including the anchor, drainage, preventing rock fall, shotcrete and vegetation were installed in the walls and slopes.

• Journal of the Korean Geosynthetics Society
• /
• v.9 no.4
• /
• pp.75-84
• /
• 2010

In this study, the long-term performance tests, which have extensibility, creep deformation, installation resistance and durability characteristic, is conducted to apply geosynthetic strip in field. The strength reduction factors using the test results are evaluated in order to calculate long-term design tensile strength. First, the creep deformation was evaluated by both the stepped isothermal method(SIM) and the time-temperature superposition(TTS) method. The creep reduction factor is reasonable to apply 1.6. Second, the result of installation damage test had little damage of yarn, which affected strength of reinforcement. Therefore, it can be analyzed that the installation damage of geosynthetic strip has little effect of long-term design tensile strength. Finally, the durability reduction factor considering chemical, biological and outdoor exposure resistance is reasonable to apply 1.1, which is considered the stability and economic efficiency of reinforced earth wall using geosynthetic strip.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.83-93
• /
• 2012

Since reinforced soil walls were introduced in domestic civil engineering society in early 1980's, various reinforcing materials including metal strips, bar mats, and sheet-type reinforcement using geotextile, geogrid, and etc. have been developed for construction purpose. Especially, the geogrid has been mostly used as a reinforcement for reinforced earth structures. This paper describes the tensile behaviors of four types of domestic geogrids. Also, a series of the wide-width tensile tests on three types of geogrids were conducted to assess the reliability of the tensile strains in geogrid measured by strain gauge. The tensile strain by strain gauge is larger than real strain of the geogrid and a difference between strain gauge reading and real strain non-linearly increase with increasing the tensile strain. However, when the tensile strain is smaller than 3%, a difference between strain gauge reading and real strain is negligible.