• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.5-6
• /
• 2006

본 시험의 목적은 수직주 및 $80^{\circ}$경사주에 대한 강도시험을 통하여 보통지선이 없는 수평지선주의 시설가능 범위를 파악하고, 전선장력에 대한 지선장력과 전주저항모멘트간의 상관관계를 실증시험을 통하여 지선 강도계산시 전주저항모멘트 적용의 타당성 여부를 조사하는 것이다. 시험결과 $2^{\circ}$이상 휘어진 전주는 지선 보강이 필요하며, 설계시 하중 작용점에 따른 전주저항모멘트는 일정한 값을 적용하여도 됨을 확인하였다. 그리고 지선강도계산식에서 전주의 저항모멘트를 고려하지 않는 것이, Y지선보다는 각 하중 작용점에 해당 불평균장력에 견디는 1조 지선을 시설하는 것이 바람직하다. 또한 보통지선이 없는 수평지선주는 지선에 작용하는 하중, 전주의 설계하중, 전주길이 및 지선의 설치위치를 고려하여 선정하여야 하여야 함을 도출하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.433-433
• /
• 2017

본 연구에서는 노후된 소규모 농업용저수지의 홍수에 대한 안전성이 부족하여 최근들어 노후된 소규모 농업용 저수지를 재설계하여 치수능력을 보강하고 있다. 이러한 노후 소규모 농업용 저수지의 홍수량을 재산정하기 위해 강우량을 수집하여 확률강우량을 재산정하고 빈도별 홍수량을 산정하였다. 산정된 빈도별 확률홍수량을 이용하여 현재의 치수적 안정성을 검토하고 현재기준에 적합한 저수지의 치수적 안정성을 갖추기 위해 댐을 증고하는 방안에 대해 검토하였다. 본 연구에서 저수지의 안정성을 검토한 결과 심천저수지의 홍수위는 200년 빈도에서 EL. 124.38m, 300년 빈도에서 EL. 124.43m 500년 빈도에서 EL. 124.48m로 현재 댐마루고 EL. 125.60m와 비교시 월류는 하지 않으나 댐설계기준(2011,국토해양부)에서 제시된 식에 따른 여유고와 비교한 결과 현재 상태에서는 여유고가 부족하여 증고가 필요한 것으로 분석되었다. 따라서 심천저수지의 현재 홍수량에 대한 검토를 위해 100년, 80년, 50년 빈도의 저수지 홍수추적결과 심천저수지의 여유고는 100년 빈도에서 0.028m부족, 80년 빈도에서 0.007m부족, 50년 빈도에서 기준여유고를 0.046m 만족하여 현재 상태에서는 50년 빈도에서 안정한 것으로 검토되었다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.66-71
• /
• 2018

In general, when an existing pier is enlarged and reinforced using a small diameter pile, bonded anchor with deformed reinforcing bars is used to maintain the integrity of the joint. However, in the case of bonded anchors, the performance depends largely on the type of joint material. Nevertheless, unlike mechanical anchors, there is no standard method for designing appropriate design methods and proper performance evaluation. Therefore, in this study, the performance of the anchoring anchor was evaluated by performing a model experiment using the reinforcing bars and anchor reinforcing bars. Experimental results show that the structural performance of the unbonded specimen is the best, and the failure mode is the punching shear failure. The deflection of the end of the member is smaller than that of the unconnected member, The deflection of the connected member is larger than the deflection of the small connected member. As the load increases, the possibility of slippage of the anchor steel or fold connection rebar is high.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.18-29
• /
• 2013

A new precast concrete (PC) beam and column connection system using non-prestressed wire strands was recently developed. The system is composed of one unit of two-storied PC-column and PC-beams with U-shaped ends. The connection part of the column and beams is reinforced by deformed bars and non-prestressed wire strands in combination for the improvement of workability. Structural performance of this system was verified by several experimental studies. The purpose of this study is developing a design concept of the beam reinforced by deformed bars and non-prestressed wire strands in combination, in terms of the cross-sectional analysis, based on the preceded experiment. A minimum and maximum reinforcement ratio and the calculation formula for the strength of flexural member reinforced by reinforcements having different yield strengths are derived based on KBC2009. Under consideration existing research results for the application of high strength reinforcement bars, the design yield strength of the non-prestressed wire strand is suggested. An example for the cross section design, satisfying the serviceability requirements, demonstrates the applicability of the design concept developed in the study.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.4 s.65
• /
• pp.423-433
• /
• 2003

Many study have been performed to describe the elastic and inelastic behavior of H-shaped beams with web openings that generally concentrated on the monotonic loading condition and concentric web opening. The findings of the studies led Darwin to propose formulas for the design of beams with web openings considering local buckling. While the formulas are simple and useful in real situation, more studies arc needed on their cyclic loading condition. In this experimental study, 12 H-shaped beams with web openings under cyclic loading condition were investigated. The dimension criteria based on the formulas proposed by Darwin were examined. The suitability of existing design formulas and the effects of plastic hinges on beams with web openings and of local buckling around web openings on the beam strength under cyclic loading were also studied. This was done by observing their behavior with various dimensional openings, eccentric per cent, and stiffeners.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.579-588
• /
• 2021

Reinforced earth retaining walls have been widely used in recent years, as they are superior from the landscape perspective than normal concrete retaining walls. However, as reinforced earth retaining walls are made of various materials depending on site, existing design methods cannot secure stability, and a variety of problems have occurred. Studies on the design and stability analysis methods, which are different from existing methods, have been conducted to address these problems. This study conducted a stability investigation using numerical analysis, and blocks of reinforced earth retaining walls were individually applied, which is different from pre-existing numerical analyses. To verify the input values of the numerical analysis when applying individual blocks, real-scale experiments of the friction characteristics between the blocks and the connection properties between the blocks and stiffener were conducted. The applicability of the block conditions, which were the same as those of real sites, was verified through numerical analysis, and will be used for the stability review and design of various combinations of blocks and stiffeners.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.2A
• /
• pp.109-118
• /
• 2009

A new bridge system described in this paper uses concrete-filled steel tube (CFT) girders as a replacement for conventional girders. Experimental investigations were carried out to comprehend the flexural behavior of CFT girder. Specimens were manufactured considering several parameters such as the strength of filling material, the eventual presence and number of inner shear connectors to evaluate the bending bearing capacity of CFT girder. The experimental investigation consisted of designing and constructing a test specimen and loading it to collapse in bending to check the applicability of the system. Test results showed that concrete filled steel tube girders have good ductility and maintain their strength up to the end of the loading. The stiffening effect of the ㄱ-shaped perfobond rib is determined to contribute relatively to the increase of the bending bearing capacity.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.231-237
• /
• 2008

This study was performed to evaluate joint behavior of prestressed concrete(PSC)-steel mixed girders through the flexural test of 14 beams according to embedded length, amount of reinforcing steel, stud arrangement, and prestressing force. All test beams were failed by turns of desertion of reinforcing steel, stud, and steel plate. From test results, prestressing force was more effective on performance of connection than stud arrangement and reinforcing steel. And the spacing of stud is also more effective than embedding length. This paper also presented 3D nonlinear analysis considering the slip of composite section as well as the static load tests of PSC-steel mixed girders. According to the slip modulus, the nonlinear analysis showed that the behavior of hybrid girders could be divided into three parts as full-composite, partial-composite and non-composite. However, the experimental results showed that the PSC-steel hybrid girders with shear connectors took the part of partial composite action in ultimate load stage. In addition, it was founded that stud shear connectors and welded reinforcements were contributed to improve the ultimate strength of hybrid girders for about 20%.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.5
• /
• pp.135-142
• /
• 2022

In this study, lap spliced ultra-high strength reinforced concrete beams were tested and the code criteria for calculating the lap splice length which was affected by the transverse reinforcement and concrete covering performance were reviewed. The main variables for test were set as fiber volume fraction and transverse reinforcing bar arrangement to improve the confining performance of the concrete cover. The change of the confining performance of concrete cover according to the increase in the fiber mixing amount at 1% and 2% volume ratio was examined, and D10 stirrups with a spacing of 100 mm were placed in the lap spliced region. As a result of the test, the specimens confined by the stirrups showed a sudden drop of load bearing capacity with horizontal cracking at the position of tensile longitudinal reinforcement. However, horizontal cracks were not appeared at the location of longitudinal reinforcement for the specimens with steel fiber. And these specimens showed gradual decrease of load bearing capacity after experiencing peak load. In particular, it was found that the strain at the position of the tensile longitudinal reinforcements of the specimens to which the mixing ratio of 2% was applied exceeds the yield strain. As a result of measuring the strain on the concrete surface, it was found that the fiber was more effective in preventing damage to the concrete surface than the stirrups for short lap spliced region.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.81-90
• /
• 2013

The purpose of this study is to evaluate the horizontal shear strength on the interface between PC and cast-in-place concrete for PC composite beams. Six specimens were tested to examine the structural performance of the horizontal interface with different surface condition and stirrup detailing. Except for SF-291B specimen failed in flexural compression, strengths and deformation capacities of five specimens were determined by horizontal shear failure. Horizontal shear strengths by composite horizontal shear or shear friction in current codes could be used to predict the horizontal shear capacity of the interface for specimens. Also detailing for stirrup by PCI design provision could be used to accomplish the composite action in the interface.