• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.2
• /
• pp.178-184
• /
• 2012

This paper presents a transformable track mechanism for wall climbing robots. The proposed mechanism allows a wall climbing robot to go over obstacles by transforming the track shape, and also increases contact area between track and wall surface for safe attachment. The track mechanism is realized using a timing belt track with one driving actuator. The inner frame of the track consists of serially connected 5R-joints and 1P-joint, and all joints of the inner frame are passively operated by springs, so the mechanism does not require any actuators and complex control algorithms to change its shape. Static analysis is carried out to determine design parameters which enable $90^{\circ}$ wall-to-wall transition and driving over projected obstacles on wall surfaces. A Prototype is manufactured using the transformable track on which polymer magnets are installed for adhesion force. The size of the prototype is $628mm{\times}200mm{\times}150mm$ ($Length{\times}Width{\times}Height$) and weight is 4kgf. Experiments are performed to verify its climbing capability focusing on $90^{\circ}$ wall to wall transition and driving over projected obstacle.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3833-3838
• /
• 2009

This paper introduces a measurement system for mechanical properties of sport shoes using an industrial robot. The robot system used in this paper is a commercial Puma type robot system(FARA AT2 made by SAMSUNG Electronics) with 6 joints and the end-effector is modified to produce a human walking motion. After analyzing human walking with a high speed video camera, each joint angle of the robot system is extracted to be used in the robot system. By using this system, ground impact forces were measured during stepping motion with 3 different shoe specimens made of 3 different hardness outsoles, respectively. As other mechanical properties, both bending moments to bend the toe part of the same specimen shoes and pronation quantities during walking motion were measured as well. In the impact test with the same depth of deformation under the ground level, the effect of the outsole hardness was clearly appeared such that the harder outsole produces the higher ground reaction force. The bending test and the pronation test also show proportional increments in the bending stiffness and the moment Mx according to the outsole hardness. Throughout such experiments, the robot system has produced consistent results so that the system could be used in obtaining valuable informations for a shoe designing process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.666-672
• /
• 2017

Our research team is developing a 6-DOF manipulator for narrow workspaces in press forming processes, such as placing PEM nuts on the bottom of a chassis. In this paper, kinematic analysis was performed for the position control of the manipulator, along with structural analyses for position accuracy with different payloads. First, the Denavit-Hatenberg (DH) parameters are defined, and then the forward and backward kinematic equations are presented using the DH parameters. The kinematic model was verified by visual simulation using Coppelia Robotics' virtual robot experimentation platform (V-REP). Position accuracy analysis was performed through structural analyses of deflection due to self-weight and deflection under full payload (5 kgf) in fully opened and fully folded states. The maximum generated stress was 22.05 MPa in the link connecting axes 2 and 3, which was confirmed to be structurally safe when considering the materials of the parts.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.4
• /
• pp.11-21
• /
• 2000

This paper proposes a new algorithm for a mobile robot that detects and tracks a moving target, keeping it in the view range of the robot. The sensor system consists of a camera and a line light source. The camera system is placed so that the line light projected into the ground from the light source forms its image along the horizontal center line of the CCD array of the camera. The deformation of the line image from the horizontal center line contains the information on existence of a moving object, its velocity, and position. Since the proposed algorithm reduces the region of the image to be searched, it reduces the computational complexity significantly comparing to the conventional image processing algorithms. The performance of the proposed algorithm has been tested by implementing on a mobile robot.

• Prospectives of Industrial Chemistry
• /
• v.23 no.2
• /
• pp.40-50
• /
• 2020

소프트 로봇의 수요와 관심이 증가함에 따라 생체 모방형 액추에이터 연구가 큰 관심을 받고 있다. 액추에이터란 외부 에너지를 기계적인 동작으로 변환하는 장치이며, 재료 자체가 유연하여 부드러운 움직임을 재현할 수 있는 소프트 액추에이터의 연구가 활발히 진행되고 있다. 고분자 연성 재료 중에 하나인 하이드로겔은 90% 이상이 물로 구성되어 있기 때문에 생체 친화적이면서 동시에 환경 친화적인 재료이며 이를 기반으로 한 액추에이터 연구가 새로이 각광받고 있다. 최근에는 하이드로겔 액추에이터의 성능 향상을 위해 나노재료를 하이드로겔에 첨가하는 연구가 진행되고 있으며, 나노재료가 갖는 고유의 특성을 활용함으로써 하이드로겔 액추에이터의 자극 감응성 향상, 변형 방향의 제어, 높은 변형 효율 그리고 기계적 물성 증가가 보고되고 있다. 이는 헬스케어를 위한 웨어러블 장치, 재활을 목적으로 한 인공 근육 등에 적용이 가능하다. 본 기고문에서는 자극 감응성 고분자와 나노재료를 이용한 하이드로겔 액추에이터 연구에 대해 자극(전기장, 빛, 열, 자기장)의 종류에 따라 분류하여 소개하고, 합성 전략 및 구동 원리에 대해 간략하게 설명하고자 한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.227-229
• /
• 2021

The modern society is advancing from the analog era to the digital imaging era, and in line with the trend of this era, various imaging devices such as exploration robots, medical equipment, and CCTV are helping our daily life a lot. However, noises caused by various causes in digital images not only cause image deterioration, but also deteriorate and deteriorate image quality. A typical noise is AWGN, and types of filters to remove it include an average filter, a median filter, and an alpha-trimmed average filter, but these filters have a disadvantage in that they show somewhat inadequate noise reduction performance in the high frequency region. Therefore, in this paper, a modified spatial division average filter based on standard deviation is proposed to effectively reduce AWGN existing in the high frequency region of the image.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.385-391
• /
• 2008

To effectively cope with a complexity of kinematic metrology due to workspace enlargement of the planar stage, the linear induction motor is suggested as its new driving source. Especially, the linear induction motor under uniform plate type of secondary doesn't inherently have a periodical force ripple which is generally shown in the brushless DC motor. But, it presents a poor transient characteristic at zero or low speed zone owing to time delay of flux settling, resulting in slow response. To improve the servo property of linear induction motor and apply successfully it to the precision stage, this paper discusses a modified vector control methodology. The controller has a novel input form, fixed d-axis current, q-axis current and forward-fed DC current, to control thrust force and normal force of the linear induction motor independently. Influence of the newly introduced input and the feasibility of controller are validated experimentally.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.9
• /
• pp.910-914
• /
• 2007

In this paper, an experimental study is performed to adjust position of compliance center of Elastomer Shear Pad Remote Center Compliance (ESP RCC) device, which is used on precise peg in hole process. In the study, variation of the lateral/axial stiffness of the ESP is proposed as a control parameter to adjust the position of compliance center of the ESP RCC. The variation of the stiffness of the ESP is achieved by controlling the shear stress of the ESP. To control the shear stress of the ESP, position of top side of the ESP is changed while remaining bottom side of the ESP is fixed on the RCC plate. To evaluate effect of the proposed idea, stiffness variations of the ESP on various shear stresses are measured, and variation of the compliance center is measured with the ESP RCC that can control the position of compliance center by using the shear stress. The measured data shows unique characteristics that have not been shown in other types of ESP VRCCs.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.5
• /
• pp.457-463
• /
• 2006

Recently proposed control scheme for a stable teleoperation, which was based on two-port time-domain passivity approach[21], has been successful for a contact with high stiffness environments. However, we found several conservatisms during the contact with deformable environments and unconstrained motion. The two-port time-domain passivity controller was excessively dissipating energy even though it was not necessary for some cases of an unconstrained motion and soft contact. The main reason of those conservatisms was on the fact that the two-port time-domain passivity controller was activated without considering the amount of energy dissipation at the master and slave manipulators. Especially, the exclusion of the slave manipulator from the two-port was the dominant reason of the conservatisms. In this paper, we consider the amount of energy dissipation at slave manipulator for designing the time-domain passivity observer and controller. The measured interaction force between slave manipulator and environment allow the time-domain passivity observer to include the amount of energy dissipation at the slave manipulator. Based on the modified passivity observer, reference energy following method[24] is applied to satisfy the passivity condition in real-time. The feasibility of the developed methods is proved with experiments. Improved performance is obtained for an interaction with deformable environments and an unconstrained motion.

• Composites Research
• /
• v.37 no.4
• /
• pp.310-315
• /
• 2024

An auxetic structure with negative Poisson's ratio exhibits distinctive mechanical properties in contrast to conventional structures, garnering interest in various fields. However, current research has predominantly focused on the design and optimization of auxetic structures, with limited exploration of their practical applications. In this study, we utilized 3D printing technology to fabricate a soft auxetic structure with triangular shaped perforations, examining the mechanical properties based on geometric structure. Additionally, by inserting shape memory alloys into the fabricated soft auxetic structure, we achieved active two-dimensional deformations and confirmed its selective object permeability. This technology holds the potential to have far-reaching implications across a broad spectrum of industries.