• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.31-40
• /
• 1998

To predict residual stresses of aluminum ring rolls after quenching and element removal, 2-D and 3-D thermal elasto-plastic analyses were performed. Strains measured by three step sectioning method were directly compared to those analysed using ABAQUS's element removal. Numerical residual stresses after quenching had similar tendency to measured ones after 2 step aging, but the difference between numerical and measured ones was large. The difference is the reason why there are nonuniform residual stress distributions to ring height direction due to small height of ring, It is judged that the increase of ring height will improve the accuracy of measured ones and decrease the difference. By direct comparison between 3-D numerical strains to simulate three step sectioning method and measured ones, the accuracy of measurement and analysis can be improved. It is concluded that there can be predicted the deformation behavior on machining complex shaped large structures with residual stresses.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.543-552
• /
• 1994

A series of drained plane strain compression tests was performed on dried samples of dense Toyoura sand and Silver Leighton Buzzard sand prepared by air-pluviation method to find out the deformation and strength characteristics on the value of confining pressure ${\sigma}{_3}^{\prime}({\sigma}{_3}^{\prime}=0.05{\sim}4.0kgf/cm^2)$. The axial and lateral strains measured in this apparatus ranged from $10^{-6}$ up to the failure of the specimen. So the stress-strain characteristics would be investigated from very small to very large strain levels. It was found that the change of the angle of internal friction ${\phi}^{\prime}{_{max}}=arcsin\{({\sigma}{_1}^{\prime}-{\sigma}{_3}^{\prime})/({\sigma}{_1}^{\prime}+{\sigma}{_3}^{\prime})\}_{max}$ with the change of ${\sigma}{_3}^{\prime}$ is very small when ${\sigma}{_3}^{\prime}$ is lower than higher. Furthermore, the effect of confining pressure on stiffness of sands was evaluated. It was also found that for the range of shear strain ${\gamma}$ from $10^{-6}$ to those at peak, the Rowe's stress-dilatancy relation seems to be a good approximation for air-dried Toyoura sand and Silver Leighton Buzzard sand, irrespective of the change of ${\sigma}{_3}^{\prime}$.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 1994.03a
• /
• pp.38-51
• /
• 1994

지하원유비축 기지 저장공동의 원유 유출이나 기화누설을 방지하기 위하여 지하수압을 조절하는 수벽공의 운영이나 공동주위 암반의 그라우팅 공법 설계에 있어서는 공동의 굴착으로 인한 주위 암반의 변형에 따른 투수계수의 변화와 지하수위의 변화에 대한 해석이 대단히 중요하다. 본 연구에서는 순간증압법을 이용한 삼축압축하의 암석의 투수계수 측정을 통하여 변형율과 투수계수와의 관계함수식을 구하였다. (중략)

• Radiation Oncology Journal
• /
• v.4 no.2
• /
• pp.165-172
• /
• 1986

In electron therapy, lead cutout or low-melting alloy block is used for shaping the field. Material for shaping electron field affects the output factor as wet 1 as the collimation system. The authors measured the output factors of electron beams for shaped fields from Clinac-18 using ionization chamber of Farmer type in polystyrene phantom. They analyzed the parameters that affect the output factors. The output factors of electron beams depend on the incident energy, collimation system and size of shaped field. For shaped field the variation of output factor for the field size (A/P) has appearence of a smooth curve for all energy and all applicator collimator combination. The output factors for open field deviate from the curves for shaped fields. An output factor for a given field can be calculated by equivalent field method such as A/P method, if a combination of applicator and collimator is fixed.

• The Journal of the Petrological Society of Korea
• /
• v.8 no.1
• /
• pp.24-33
• /
• 1999

Differential Strain Analysis (DSA) was performed to examine the characteristics of microcracks for the granites from two sites, Noeunri and Gunggiri. The results of the DSA are taken every 5 MPa for the first 50 MPa, then every 10 MPa to a pressure of 100 MPa, and then every 15 MPa to a pressure of 250 MPa. Differential strain was measured on core samples in three horizontal directions, using $45^{\circ}$ rosette strain gages, and one vertical direction. The gradients of cumulative crack strain curves in one vertical direction and three horizontal directions differed from one another, indicating anisotropic crack development in the sample. The magnitude of vertical cumulative crack strain was the highest, indicating that the microcracks from the studied rock are generally developed in horizontal direction. Under the pressure of 240 Mpa, vertical cumulative crack strains for samples N-1, N-2, G-1, and G-2 were $74{\times}l0^{-6}~820{\times}l0^{-6},\; 190{\times}l0^{-6}~460{\times}l0^{-6},\; 329{\times}l0^{-6}~836{\times}l0^{-6},\; 833{\times}10^{-6}~1,592{\times}l0^{-6}$, respectively. Under the pressure of 25O MPa, volumetric crack strains for Gunggiri and Noeunri ranged from $1,804{\times}10^{-6}\; to\; 3,936{\times}10^{-6}\; and \;from,\; 1, 125{\times}10^{-6}\; to\; 1,457{\times}10^{-6}$, respectively. Therefore, the amount of microcrackes produced were more distributed in Gunggiri than Noeunri. The ratio of a maximum crack strain to a minimum crack strain was calculated to find the orientations between microcracks and the rift plane of the granites. Generally, the ratio has very high values ranging from 2.42 to 3.43, which suggests most microcracks to be intragranular cracks with the regular orientations. These results indicate that the preferred orientations of microcracks in the granites were almost parallel to the rift plane of the granites.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2004.06a
• /
• pp.224-225
• /
• 2004

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.700-703
• /
• 2010

일반적으로 구조부재의 안전성 평가는 계측된 센서의 변형률로부터 부재의 최대응력 또는 부재력 수준을 결정하고 설계기준에 의한 부재의 허용응력 또는 설계 강도와의 비교에 의해서 이루어진다. 그러나 이러한 설계기준은 건물의 설계단계에서 미리 가정된 하중 및 부재의 강도에 대한 여러 확률분포 또는 안전율을 반영하여 작성된 것으로 실질적으로 센서로부터 측정한 데이터를 직접 설계기준에 반영하는 것은 합리적이지 못하다. 본 연구에서는 실제 센서로부터 측정되는 변형률을 이용하여 합리적으로 구조부재의 안전성 평가를 수행하기 위한 방법을 모색하고자 한다. 설계기준을 고려한 변형률 제한치, 저감계수가 도입되었으며 이에 추가적으로 센서와 관련한 계수를 도입하여 구조부재의 안전성 평가를 위한 방향을 제시한다.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.2
• /
• pp.105-114
• /
• 1994

초경합금은 기계적 성질이 다른 WC의 분상상과 Co의 결합상으로 구성되어 있다. 만일 이합금이 거시적으로 균일하게 변형을 하면, 각 상들은 이들의 응력상태에 따라 다르게 변형될 것이다. 따라서 WC-Co 합금의 변형특성과 강화기구를 명확히 알기 위해서는 각상의 미시적 변형과 파괴기구를 검토할 필요가 있다. 본 연구에서는 시편에 굽힘하중을 가하여, X선 회절로 분산상인 WC상 및 결합상인 Co상의 X선적 탄성정수와 응력정수를 측정하였다. WC-Co합금중의 WC상과 Co상의 상응력은 WC(112)면과 CO(311)면의 회절로서 결정하였다. 그리고 이 상응력들을 복합법칙의 적용가능성에 대하여 검토하였다.

• Journal of the Korean Magnetics Society
• /
• v.25 no.4
• /
• pp.123-128
• /
• 2015

The iron is an element having a high yield strength, mechanical hardness, good electrical conductivity, and also it has been used in various fields because of ease machining. In bridges have been used tendon made of a steel wire for large loads and light weight. Tension measurement of tendon employed in PreStressed Concrete (PSC) bridge is very important for the bridge safety check. NDT (Non-Destructive Testing) is essential for the safety check, however, magnetic NDT is difficult to apply due to the non-linear magnetization curve and hysteresis loop in the magnetic properties. In this work, for basic study of magnetic NDT application, we have constructed a B-H loop measuring system for 7-strand tendon of which diameter is 15.5 mm, and which can apply tensile stress up to 2.0 GPa. We have measured hysteresis loops of two kinds of tendons under different tensile stress. Amplitude permeability and maximum magnetic induction near knee show the most sensitive and high linearity depends on tensile stress. Relative amplitude permeability was decreased from 500 to 200 and maximum magnetic flux density changed 0.6 T.

• Magazine of the Korea Concrete Institute
• /
• v.5 no.3
• /
• pp.187-194
• /
• 1993

본 논문에서는 유리섬유의 적층수, 유리섬유의 배향각도에 대한 유리섬유 강화 플라스틱(Glass Fiber Reinforced Plastics ; GFRP)의 인장거동 변화를 고찰하고, 이들의 상관관계를 규명하기 위하여 일련의 GFRP 시험체에 대하여 인장실험을 수행하였다. 시험체는 폭12.5mm, 길이 60mm크기로 일정하게 제작하였으며, 시험체에 대하여 인장실험을 수행하였다. 시험체 제작시 유리섬유로 적층수는 14, 22, 30층, 유리섬유의 배향각도는 0$^{\circ}$, 30$^{\circ}$, 45$^{\circ}$로 하였다. 인장실험시 각 시험체의 파괴양상, 극한하중 및 하중변화에 대한 인장변형율을 조사하였고, 이들 결과를 토대로 유리섬유의 적층수와 배향각도에 따른 GFRP의 극한하중, 응력-변형율 선도 및 탄성계수 등을 비교 분석하였다. 한편 본 논문에서는 유리섬유의 적층수, 직경 변화에 따른 GFRP관의 파괴거동을 고찰하기 위하여 4점 재하법에 의한 GFRP관의 휨파괴실험을 수행하였다. 실험에 사용된 시험체는 길이 1200mm로 하였으며, 유리섬유의 적층수를 30, 35, 40층, 관의 직경을 50, 100, 150mm로 하였다. 파괴실험시 각 시험체의 하중변화에 대한 휨 변형율, 중앙점 처짐량 및 항복하중을 측정하였고, 이들 결과를 토대로 유리섬유으 적층수와 관의 직경에 따라 GFRP관의 항복하중 및 파괴에너지를 비교 분석 하였으며, 항복시 파괴에너지를 추정할 수 있는 제안식을 유도하였다.