• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.129-136
• /
• 2001

본 논문에서는 석탄회 매립지반의 액상화 가능성을 평가하기 위해 순수 모래시료와 더불어서 모래시료와 석탄회가 혼합된 모래시료에 대한 일련의 진동삼축실험을 변형률제어 방법으로 수행하였다. 실험결과 진동하중에 의해서 시료 내에 발생하는 간극수압의 크기는 작용하는 전단변형률의 크기에 심각하게 영향을 받고, 작용하는 전단변형률이 지반의 한계전단변형률 보다 작은 경우에는 진동수가 높은 조건에서도 간극수압이 발생하지 않음을 알았다. 또한 전단변형률이 약 0.1%보다 작고 한계전단변형률에 가까운 경우에는 순수 모래시료와 비교하여 본 논문에서 조사한 석탄회 함유율 범위 (10%~30%)의 시료에서 간극수압이 더 크게 발생하였다. 반면에, 전단변형률이 큰 경우에는 순수 모래시료에서 간극수압이 크게 발생하는 추세를 보였다. 반복 전단에 따른 간극수압의 발생량은 전반적으로 석탄회 함유율이 증가할수록 커지는 경향을 보였다. 이러한 결과를 근거로 해안이나 하천에 인접한 한계지 개발에 있어서 사질토에 석탄회를 혼합 매립하여 지반을 조성하는 경우에 액상화에 대해서 불안정한 지반이 될 가능성이 있는 것으로 판단되었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1027-1035
• /
• 2016

In this study, a strain-controlled fatigue test of widely-used 316L stainless steel with excellent corrosion resistance and mechanical properties was conducted, in order to assess its fatigue life. Low cycle fatigue behaviors were analyzed at room temperature, as a function of the strain amplitude and strain ratio. The material was hardened during the initial few cycles, and then was softened during the long post period, until failure occurred. The fatigue life decreased with increasing strain amplitude. Masing behavior in the hysteresis loop was shown under the low strain amplitude, whereas the high strain amplitude caused non-Masing behavior and reduced the mean stress. Low cycle fatigue life prediction based on the cyclic plastic energy dissipation theory, considering Masing and non-Masing effects, showed a good correlation with the experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.122-129
• /
• 2004

In plastic working, as working becomes speedy, automatic and working condition deteriorates, the increase of forging working has been remarkable. Therefore, we need the estimation of mold lift in detail, in order to counterplan of effective mold life extension. In this study, on the SKH51, mold steel which is forged by cold working and the KCW1, tool steel of low alloy, we estimated mold life on the base of FEM analysis and investigated mold lift by low cycle fatigue test. Also, this paper suggested a new method of estimation of mold lift.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.6
• /
• pp.501-517
• /
• 2011

In general, the tunnel stability during excavation is assessed by comparing measured displacements at roof and sidewall to control criteria. The control criteria were established based on the past experience that considered ground conditions, size of the tunnel cross section, construction method, supports, etc. Therefore, a number of researches on the control criteria using the critical strain have been conducted. However, the critical strain obtained from uniaxial compression tests have drawbacks of not taking damage in rock mass due to increase of stress level and longitudinal arching into account. In this paper, damage-controlled tests simulating stress level and longitudinal arching during tunnel excavation were carried out in addition to uniaxial compression tests to investigate the critical strain characteristics of granite and gneiss that are most abundant rock types in Korean peninsula. Then, the critical strains obtained from damage-controlled tests were compared to those from uniaxial compression tests; the former showed less values than the latter. These results show that the critical strain obtained from uniaxial compression tests has to be reduced a little bit to take stress history during tunnel excavation into account. Moreover, the damage critical strain was proposed to be used for assessment of the brittle failure that usually occurs in deep tunnels.

• Proceedings of the KAIS Fall Conference
• /
• 2005.05a
• /
• pp.71-74
• /
• 2005

본 논문에서는 폐목재의 재활용을 위한 1차 파쇄기의 다음 공정인 2차 파쇄기에 대해 경계조건과 하중조건을 적응하여 유한요소법에 의한 ANSYS로 구조해석과 모달해석을 수행하여 응력(stress), 변형률(strain)을 구하고 구조적 타당성을 검토하였다. 이는 안전성을 고려한 설계의 기초 자료가 되며 고유진동수(natural frequency)를 구하여 모터의 회전을 제어함으로서 공진(resonance) 현상을 피하는데 있다.

• Proceedings of the KAIS Fall Conference
• /
• 2004.11a
• /
• pp.66-69
• /
• 2004

본 논문에서는 트레드밀의 풀리 벨트를 통해 회전하는 앞 롤러와 러닝 벨트를 통해 회전하는 뒤 롤러의 경계조건과 하중조건을 적용하여 ANSYS로 구조해석을 수행하여, 변위(displacement), 응력 (stress), 변형률(strain)을 구하여 구조적 타당성을 검토하는데 있으며, 각각의 롤러를 모달해석을 통해 고유진동수(natural frequency)를 알아보고 얻어진 데이터 값을 통해 진동 발생 요소인 모터의 회전을 제어함으로서 공진(resonance) 현상을 피하는데 있다.

• Proceedings of the KAIS Fall Conference
• /
• 2004.11a
• /
• pp.80-82
• /
• 2004

본 논문에서는 폐목재의 재활용을 위한 파쇄기의 경계조건과 하중조건을 적용하여 유한요소법에 의한 ANSYS로 구조해석과 모달해석을 수행하여 변위(displacement), 응력(stress), 변형률(strain)을 구하고 구조적 타당성을 검토하였다. 이는 안전성을 고려한 설계의 기초자료가 되며 고유진동수(natural frequency)를 구하여 모터의 회전을 제어함으로서 공진(resonance) 현상을 피하는데 있다.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.7
• /
• pp.25-36
• /
• 2008

The plane strain test can reproduce the real field condition and failure behavior precisely over other laboratory shear tests. Accordingly, this test has been utilized to investigate the shearing behaviors associated with overall failure behavior and local deformation of soils. However, most plane strain tests have been carried out with restrained end plates due to difficulties in manufacturing the equipment and also performing it. This restraint induces different results with real field because of shear stress on end plates. In this study, plane strain tests with/without bottom plate restraint were performed on Jumunjin-sand. The measurement of overall and local deformation was accomplished by digital image correlation technique as well as external LVDT. By applying digital image correlation method using two consecutive images captured through the transparent wall, local deformation behavior of various parts inside the specimen was estimated. And the formation and development of shear band caused by the restrained effect of end plate and the deformation mechanism of sand under plane strain condition were examined.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.65-75
• /
• 2024

This study investigates liquefaction-induced settlement through strain-controlled tests using a cyclic direct simple shear device on clean sand specimens. By focusing on the accumulated shear strain, soil density, sample preparation method, and cyclic waveshape, this study attempts to enhance the understanding of soil behavior under seismic loading and its further deformation. Results from tests conducted on remolded samples reveal insights into excess pore water pressure development and post-liquefaction volumetric strain behavior, with denser samples exhibiting lower volumetric strains than looser samples. Similarly, the correlation between the frequency and amplitude variations of the wave and volumetric strain highlights the importance of wave characteristics in soil response, with shear strain amplitude changes, varying the volumetric strain response after reconsolidation. In addition, samples prepared under moist conditions exhibit less volumetric strain than dry-reconstituted samples. Overall, the findings of this study are expected to contribute to predictive models to evaluate liquefaction-induced settlement.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.53-64
• /
• 2012

In this study, the modified cyclic triaxial tests with Joomunjin standard sand are performed for dynamic deformation characteristics, such as Young's moduli and damping ratio. The cyclic triaxial test is equipped with Local Displacement Transducer (LDT) on the outside of a cell which has a range from $10^{-4}$ to $10^{-1}$ of shear strains, ${\gamma}$ (%), instead of conventional cyclic triaxial test which has linear variable displacement transducer (LVDT) with low precision. With the small strain control, tests were carried out at various loading rates, void ratios, and effective confining pressures. Based on the test results, such as dynamic deformation characteristics, shear modulus, and damping ratio, it is found that the test can measure more range of medium strains (0.02-0.2%) than results obtained from conventional test (resonant column test). For the medium strain range, dynamic deformation characteristics investigated by the cyclic triaxial test are also different from those predicted by nonlinear model in conventional test.