• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.458-466
• /
• 2020

The purpose of this experimental research is to evaluate the compressive and tensile behaviors of high performance hybrid fiber reinforced concrete(HPHFRC) using amorphous steel fiber(ASF) and polyamide fiber(PAF). For this purpose, the HPHFRCs using ASF and PAF were made according to their total volume fraction of 1.0% for target compressive strength of 40MPa and 60MPa, respectively. And then the compressive and tensile behaviors such as the compressive strength, compressive toughness, direct tensile strength, and stress-strain characteristics under compressive and tensile tests were estimated. It was observed from the test results that the compressive strength of HPHFRC was slightly decreased than that of plain concrete, but the compressive toughness, compressive toughness ratio, and direct tensile strength of HPHFRC increased significantly. Also, it was revealed that the plain concrete showed brittle fracture after the maximum stress from the stress-strain curves, but HPHFRC showed strain softening.

• The tire
• /
• s.65
• /
• pp.10-17
• /
• 1976

아민계열화방지제(이하 아민이라고 한다)를 첨가한 천연고무 순고무가유물에 대해서 고온으로 반복대신장피로를 주어서 응력변화, 피로수명에 주는 열화방지제의 영향을 조사하였다. 아민첨가시료에 대해서 고온으로 반복 신장피로를 가하면 무첨가시료와 동양, 화학응력 연화가 출현했다. 아민첨가시료의 화학응력연화의 임계온도는 NR-DPG로 110℃, NR-MBTS로 110℃, NR-TT로 130℃이며 가교구조의 내열성에 일치하며 무첨가시료의 임계온도보다도 10~30℃높아졌다. 아민첨가시료의 반복신장피로수명은 60℃로 극대화 되어 (NR-DCP만이 40℃이었으나) 무첨가시료의 피로수명은 40℃에서 극대화됐다. 전보에서 보고한 피로수명과 변형률과의 관계식(F=A(εb-ε)n)은 100℃에서 아민첨가시료에 대해서만이 성립하고 무첨가시료에 대해선 성립되지 않았다. 이들의 결과는 아민을 고무에 첨가함으로써 고무의 열산화반응이 억제되었음에 원인하고 있다고 생각된다.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.307-314
• /
• 2016

Shear characteristics of soils can be investigated using various types of shear stress measuring apparatus. Ring shear tests are often applied for examining the residual shear strength under the unlimited deformation. This paper presents drainage-consolidation-shear velocity dependent undrained shear strengths measured in terms of water leakage. A series of ring shear tests were performed under the constant normal stress (50 kPa) and controled shear velocity ranging from 0.01~1 mm/sec under the undrained condition. As a result, undrained shear strengths are dependent on shear velocity. It exhibits that straining hardening behavior is observed for the shear velocity lower than 0.1 mm/sec; however, the strain softening behavior is observed for the shear velocity higher than 0.1 mm/sec. Water leakage can cause the increase in shear stress irrespective of shear velocity. Shear stress increases with increasing amount of water leakage. It is due to the fact that the small grains and water flow out through the rubble edge in the ring shear box. Repetitive saturation and consolidation processes may minimize the error.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.285-290
• /
• 2004

Low cycle fatigue tests are performed on the Inconel 617 that be used for a hot gas casing. The relation between strain energy density and numbers of cycles to failure is examined in order to predict the low cycle fatigue life of Inconel 617. The life predicted by the strain energy method is found to coincide with experimental data and results obtained from the Coffin-Manson method. Also the cyclic behavior of Inconel 617 is characterized by cyclic hardening with increasing number of cycle at room temperature.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.2
• /
• pp.129-138
• /
• 1996

Localization of concrete is a phenomenon such that the deformation of concrete is localized in finite region with softening behavior and it governs ultimate load of concrete. In this Paper, concrete under strain localization was modeled with localization region and non-localization region and lc~calization behavior was formulated based on averaging concept of heterogeneous material. By using the formulation, the localization phenomena of concrete under uniaxial loadings were well predicted. The analytical results show that size of localization region of concrete under uniaxial compression is three times of maximum aggregate size and the size effect of concrete is well predicted. The use of tension-softening curve obtained from direct tension test is suitable for well prediction of localization of concrete under uniaxial tension.

• Journal of the Korea Concrete Institute
• /
• v.16 no.6 s.84
• /
• pp.767-776
• /
• 2004

Polymer concrete shows excellent mechanical properties and chemical resistance compared with conventional normal cement concrete. The polymer concrete is drawing a strong interest as high-performance materials in the construction industry. Resins using recycled PET offer the possibility of a lower source cost of materials for making useful polymer concrete products. Also the recycling of PET in polymer concrete would help solve some of the solid waste problems posed by plastics and save energy. The purposed of this paper is to propose the model for the stress-strain relation of recycled-PET polymer concrete at monotonic uniaxial compression and is to investigate for the stress-strain behavior characteristics of recycled-PET polymer concrete with different variables(strength, resin contents, curing conditions, addition of silane and ages). The maximum stress and strain of recycled-PET polymer concrete was found to increase with an increase in resin content, however, it decreased beyond a particular level of resin content. A ascending and descending branch of stress-strain curve represented more sharply at high temperature curing more than normal temperature curing. Addition of silane increases compressive strength and postpeak ductility. In addition, results show that the proposed model accurately predicts the stress-strain relation of recycled-PET polymer concrete

• Korean Journal of Materials Research
• /
• v.3 no.1
• /
• pp.50-57
• /
• 1993

Abstract The sintering behavior of the mechanically alloyed AI-8wt%Fe power during vacuum hot pressing was investigated and high temperature deformation behavior of the sintered specimen was studied through compression tests at various strain rates in the temperature range between 35$0^{\circ}C$ and 45$0^{\circ}C$. In 'addition, thermal stablity of the sintered specimem was examined by hardness measurement after annealing the spcimem for 60 hours in the temperature range of 30$0^{\circ}C$ ~50$0^{\circ}C$. The compressive stress increased rapidly with strain and reached the maximum point at the strain about 3%. With slight decrement after reaching the maximum point, the flow stress became constant up to the strain of 30% and it was considered to be due to equilibrium between work hardening and dynamic recrystallization. The hardness of the 60 hrs annealed specimens began to decrease rapidly at 40$0^{\circ}C$ .

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.59-70
• /
• 2008

도심지 터널의 설계, 시공 그리고 유지관리에 있어서 지반 변위 억제와 변형거동 예측은 중요하다. 국내 외 연구자들은 다양한 수치해석적인 기법과 현장 계측 결과를 이용하여 터널 시공과 관련된 변형거동 예측을 시도하였다. 하지만, 설계물성치의 산정과 지반 모델링 그리고 수치해석기법과 관련된 사용상의 어려움에 의해 아직까지 만족스러운 결과를 얻지는 못하였다. 본 논문은 수치해석적인 기법과 인공신경망을 이용하여 도심지 NATM 터널의 설계 물성치 산정과 변형거동 예측에 관한 방법을 제안하였다. 인공신경망 모델 개발을 위한 학습과 테스트과정은 데이터베이스된 수치해석결과를 이용하였다. 개발된 인공신경망 모델은 입력변수인 지반변위와 결과변수인 설계 물성치 간의 상호관계를 적절히 인식할 수 있다. 수치해석은 지반의 연화거동을 모사할 수 있는 변형률 연화모델을 적용하였다. 사례분석에 있어서 굴착 초기단계의 계측 값을 개발된 인공신경망 모델에 입력하여 설계 물성치를 계산하였으며, 수정된 설계 물성치는 수치해석을 통하여 다음 굴착단계에서의 터널 주변의 지반 변형거동을 예측하였다. 본 논문에서 제안된 방법을 토대로 시공조건이 엄밀한 도심지 터널의 설계물성치의 정량적인 평가 및 변형거동 예측이 계측이 입수된 초기 굴착단계에서 가능할 것으로 기대된다.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.151-161
• /
• 1994

FCAW has wide application in ship fabrication, maintenance and field erection. It has many advantages over SMAW.SAW and GMAW process. In many applications, the FCAW provides highquality weld metal. This method can reduce weld defects especially porosity and spatter. But the fatigue characteristics of those deposited metal have been rarely investigated. The purpose of this study is to investigate the cyclic stress-strain behavior and fatigue tests by the constant strain control were carried out on the rounded smooth specimen with deposited metal using the metal type flux cored wire. As the results of this study for the deposited metal welded by the metal type flux cored wire, the hardening or softening characteristics under cyclic load were investigated and cyclic stress-strain curve, strain-fatigue life curve, stress-strain function and fatigue life relation which are useful to estimate the fatigue life under the stress concentration condition were obtained.

• Korean Journal of Materials Research
• /
• v.7 no.11
• /
• pp.1007-1011
• /
• 1997

영활화혁발전소 보일러헤다 재질인 1Cr0.5Mo강의 파형에 따른 저주기 피로특성을 규명하고자 상온(298K) 및 고온(177K)의 삼각파와 사인파형 저주기 피로시험을 수행하였고 소성에너지법을 이용하여 파형에 따른 소성변형에너지와 피로수명과의 +관계를 분석하였다. 저주기 피로시 재료내부의 소성변형에너지를 히스테리시스루프의 면적으로 계산하여 구하였으며 이를통해 저주기 피로수명을 예측하였고 Coffin-Manson법 및 변형률분할법을 이용한 저주기 피로수명 결과와 서로 잘 일치하였다. 또한 상온 및 고온에서 피로반복수의 증가와 함께 재료가 반봅연화됨을 알 수 있었다.