• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.810-817
• /
• 2015

This study was conducted to evaluate the pressure treatment characteristics of yellow poplar skin timber with ACQ-2, CUAZ-3, and CuHDO-1. The effect of moisture content (MC) on treatability was investigated, and fixation characteristics of copper-based preservatives were also evaluated. Sapwood of yellow poplar, which was dried below 50 percent MC, was fully penetrated with preservatives, and minimum requirement of preservative retention for the hazard class H3 was achieved. Through measuring retention gradient in yellow poplar sapwood, it was confirmed that minimum requirement of preservative retention for the hazard class H3 was achieved in the assay zone from the surface to 15 mm-depth when the specimens were dried below 30 percent MC. Yellow poplar heartwood did not meet the minimum requirement of penetration and retention for the hazard class H3 over the range of pretreatment MCs tested. The fixation rate of copper was much faster under drying condition compared with nondrying condition; more than 90% of copper were fixed in 3 weeks at $21^{\circ}C$ under drying conditions.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.16-25
• /
• 1987

This study was carried out under controlled laboratory conditions in order to investigate the relative durability to decay of 6 Quercus species. The relative durability to decay was expressed by the percentage of weight loss by Lentinus edodes and Pleuratus ostreatus. The results obtained could be summarized as follows: 1. The most decay-resistant parts by L. edodes were heart wood of Q. sarrata TH. and sap wood of Q. aliena BL. and the least decay-resistant parts were heart wood of Q. acutissima C. and sap wood of Q. dentata TH.. 2. The most decay-resistant parts by P. osteratus were heart wood of Q. serrata TH. and sap wood of Q. aliena BL. and the least decay-resistant parts were heart wood of Q. variabilis BL. and sap wood of Q. dentata. TH.. 3. The percentage of weight loss in 6 Quercus species by section-height was not a consistent variation. 4. Putting these results together, Quercus aliena BL, could be regarded as the most decay-resistant by L. edodes and P. osteratus under normal condition among 6 Quercus species.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.2
• /
• pp.45-51
• /
• 2003

One flavonoid, lignan glycosides and two diarylheptanoids were isolated from the sapwood of Betula maximowicziana. The structures were determined as : catechin 7-O-𝛽-D-xylopyranoside, lyoniresinol 9'-O-𝛽-D-glucopyranoside, 11-oxo-3, 8, 12, 17-tetrahydroxy-9-ene[7, 0]-metacyclophane and 11-oxo-3, 8, 9, 10, 12, 17-hexahydroxy[7, 0]-metacyclophane, respectively, on the basis of spectrosopic data and chemical correlations.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.481-489
• /
• 2011

This study was conducted to evaluate the pressure treatment characteristics of Japanese red pine and Japanese larch skin timber with ACQ-2, CUAZ-2 and CuHDO-1. The effect of moisture content (MC) on preservative treatability was investigated for Japanese red pine sapwood and Japanese larch heartwood, and fixation characteristics of CCA alternatives was also evaluated. Japanese red pine sapwood, which was dried below 30 percent MC, was fully penetrated with preservatives, and minimum requirement of preservative retention for the hazard class H3 was achieved. Through measuring preservative retention gradient in Japanese red pine sapwood, it was confirmed that the retention gradient of CuHDO-1 was steeper than that of both ACQ-2 and CUAZ-2. In particular, it was intensified at a higher MCs of wood samples (25∼30%). Japanese larch heartwood did not meet the minimum requirement of penetration and retention for the hazard class H3 over the range of pretreatment MCs tested. With presteaming under $121^{\circ}C$ for 12 hours, the treatability of Japanese larch heartwood was enhanced to meet the minimum requirement for the hazard class H3. The fixation rate of copper was much more faster under drying condition compared with nondrying condition; more than 95% of copper were fixed in 3~6 days and 1 day under drying conditions in Japanese red pine sapwood and Japanese larch heartwood, respectively. After 3-week fixation period at ambient temperature, the amount of mobile copper in treated wood sample that remains available for leaching from treated wood was the highest in the wood samples treated with ACQ-2, followed by CuHDO-1 and CUAZ-2. It was proportional to the amount of copper in treating solution.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.701-713
• /
• 2015

A model was designed to identify wood species between Pinus densiflora for. erecta Uyeki and Pinus densiflora Sieb. et Zucc. using the near-infrared (NIR) spectroscopy in combination with principal component analysis (PCA) and partial least square discriminant analysis (PLS-DA). In the PCA using all of the spectra, Pinus densiflora for. erecta Uyeki and Pinus densiflora Sieb. et Zucc. could not be classified. In the PCA using the spectrum that has been measured in sapwood, however, Pinus densiflora for. erecta Uyeki and Pinus densiflora Sieb. et Zucc. could be identified. In particular, it was clearly classified by sapwood in radial section. And more, these two species could be perfectly identified using PLS-DA prediction model. The best performance in species identification was obtained when the second derivative spectra was used; the prediction accuracy was 100%. For prediction model, the $R_p{^2}$ value was 0.86 and the RMSEP was 0.38 in second derivative spectra. It was verified that the model designed by NIR spectroscopy with PLS-DA is suitable for species identification between Pinus densiflora for. erecta Uyeki and Pinus densiflora Sieb. et Zucc.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.1
• /
• pp.42-47
• /
• 2000

This study was designed to investigate the effect of treatment variables on CCA treatment of Japanese red pine (Pinus densiflora), Japanese larch (Larix leptolepis), and ezo spruce (Picea jezoensis) round posts. Variables included were duration of initial vacuum (30, 45, or 60 minutes) and maximum pressure applied (8.5, 10.5, or 14.0 kg/$cm^2$), and maximum pressure was maintained until refusal point was reached. Regardless of wood species, extending the duration of initial vacuum more than 30 minutes did not affect treatability. Increasing pressure did not affect preservative penetration; however, preservative retention was affected by pressure levels, particularly at higher level (14.0 kg/$cm^2$). Preservative penetration depth of Japanese red pine met a minimum requirement specified by Notification of Korean Forestry Administration (No. 1999-8) for hazard class H5 of CCA-treated wood. Penetration of preservative in both Japanese larch and ezo spruce was not deep because of shallow sapwood thickness of these species, so pretreatment such as incising should be considered if these species are treated with preservatives. Although retention in Japanese red pine was not significantly increased even with 14.0 kg/$cm^2$, that of refractory Japanese larch and ezo spruce was significantly increased with the application of 14.0 kg/$cm^2$. Effect of treatment variables on refusal time was unclear; however, it is cleared that the refusal time was shortened with the increase in sapwood thickness.

• Journal of Conservation Science
• /
• v.7 no.2
• /
• pp.60-67
• /
• 1998

The effects of moisture content (MC) and diffusion period on the diffusion of boron from borate rod through Pinus densiflora and P. koraiensis were investigated as a preliminary research of integrated remedial treatment for heritage wooden structures using borate rod. After equilibrating MCs of samples (15, 25, and 40%), borate rod (1,000 mg) was inserted into the sample, and stored for diffusion of boron at room temperatures ($23^{\circ}C$) for 2, 4, 8, and 12 weeks. Wafers were serially cut at constant intervals from rod treatment point and the boron penetration through longitudinal and transverse direction was measured by staining with boron indicator. For boron diffusion, MC above fiber saturation point was needed, and the diffusion rates increased with time. The fastest rates of diffusion were observed in longitudinal direction, followed by the radial and then the tangential direction. The rates of diffusion in all directions were the fastest in P. koraiensis. In P. densiflora, the diffusion rates through heartwood was faster than that in sapwood in longitudinal direction and vice versa in transverse direction. Based on the best result of this study, optimal space between rod insertion points could be recommended as follows; approximately 120 mm for P. koraiensis and heartwood of P. densiflora, 60 mm for sapwood of P. densiflora in longitudinal direction, and approximately 30 mm for all species tested in transverse direction. However, the effect of rod size and long-term exposure for diffusion on boron movement should be fully investigated for the accurate evaluation of optimal space between rod holes.

• Journal of Korean Society of Forest Science
• /
• v.79 no.4
• /
• pp.419-423
• /
• 1990

This study was carried out to investigate the cause of pith-damaged wood formation, the state of growth, and difference of chemical composition of Japanese Larix(L. leptolepis Gorden). 1. Larix grew normaly to 10 years, and the volume increment was 32.4%. But it was gradually decreased to 19.4% from 11 to 13 years that the heartwood damage was occurred. Therefore, the volume increment was decreased 13%. The decayed wood was formed from fire wound portion of bark by forest fire. The volume loss from pith-dagmaged wood occurred by forest fire was more than 20%. 2. On the ash content, heartwood(0.05%) and pith-damaged wood(0.08%) was lower than sapwood(0.29%). The difference of extractive contents are considered the reason. It is considered that this ash content difference is depend upon the extractive contents among sap, heart and decayed wood parts. Holocellulose contents were from 54.3% to 59.3% and there were no difference among heartwood, pith-damaged wood, and sapwood, On the pentosan contents, heartwood(6.3%) and pith-damaged wood(6.6%) were higher than sapwood. Lignin contents of pith-damaged wood was tower than heartwood (34.4%). This seems to weaken all kinds of wood strength.

• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.63-71
• /
• 1999

본 연구는 목재중의 수분량이 변화하는 비정상태하에 있어서의 액체투과성을 평가하기 위한 새로운 방법으로써 원심법에 의한 액체투과성을 평가하기 위한 새로운 방법으로써 원심법에 의한 액체투과성의 평가법을 확립해 보고자 실시하였다. 이 방법은 원심력장에 있어서의 액체투과성과 원심처리부로부터 액체투과성을 평가하는 것이다. 실험결과, 삼나무(Cryptomeria japonica)와 미송 (Pseudotsuga menziesii)은 서로 다른 탈수경과를 나타내었다. 삼나무는 미송보다 더 많은 탈수량을 보였고 재내의 태수량의 변이가 심하였다. 한편 변재와 심재의 탈수거동에 있어서 삼나무는 기체투과성에 의해 평가된 값과 상반된 결과를 나타내었다. 즉, 2200∼3300rpm의 범위에서 편재는 심재보다 탈수량이 적었다.

• Journal of the Korean Professional Engineers Association
• /
• v.44 no.5
• /
• pp.36-41
• /
• 2011

Design of blast resistant structures (protective structures) require the adequate design and construction practices as well as the knowledge of characteristics of the blast loads, behavior of structures and their components under these loads. This paper focuses on how to design and evaluate the structures for blast resistance, and provides principles and discussion on analysis and design capability in protective technology and recommendations.