• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.147-159
• /
• 1982

내부에 정방형, 외부에 원형인 두 정온동심수평관으로 이루어진 폐쇄공간에서 열부력으로 야기된 대류열전달 현상을 연구하였다. 주어진 비정규적 형상에서의 층류 정상 Boussinesq 유동을 해 석하기 위하여, 지구중력방향에 대하여 가능한 두 개의 대칭형 위치에 관하여, Galerkin 유한요 소법을 사용하였다. 이론의 결과를 확증하기 위하여 실험적으로도 온도측정과 유선의 가시화를 수행하였다. 정방형내관의 직각인 선단은 국소 및 총체열전달에 있어서 소극적인 역할을 하지만, 이들로 인한 경계층 유동의 박리는 발생하지 아니함을 보였다. 이 내관의 상부 수평면상에서는 유동속도와 온도구배가 낮기는 하나 확연한 대칭형의 열상승류(Plume)가 가능하였다. 내관의 벽면들이 지구중력방향에 관하여 .+-.45.deg.의 각을 이룰 경우 과류의 중심부가, Rayleigh수가 6.5*$10^{4}$보다 작을 때는 4개, 이보다 클때는 2개가 폐쇄공간 안에서 발생하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.69-75
• /
• 2009

This paper studies the aerodynamic performance that the vent mixer-new conceptual supersonic mixer-showed with its geometric characteristics. The hole is 2 mm with 2 mm's distance from the wall in case 1 and with no distance in case 2. In case 3 die hole is 1 mm. Case 1 and case 2 showed the same total pressure recovery ratio, of which the case 3 was lower than that. While cases 1-3 had the same reattachment length, the shear layer was thicker in cases 1 and 2 than in case 3. Within the recirculation zone, cases 1 and 2 had lower pressure loss and higher velocity gradient difference than case 3-they enhance mixing between air and fuel. Separation bubble which is developed by the inflow into the recirculation zone has a significant effect on the total pressure recovery ratio in the combustor. Also separation bubble influences pressure distributions and recirculation flows in the recirculation zone. Therefore, inflow rate of air into the recirculation zone mainly affects the performance of vent mixer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.2
• /
• pp.287-298
• /
• 1989

A numerical work was performed to study the flow behaviors of the open channel type flow with its geometric boundary conditions being similar to that of the Multi-Stage-Flash evaporator with and without a baffle. For the analysis, two-dimensional steady turbulent flow was assumed and the widely known k-.epsilon. turbulence model was usded. SIMPLE algorithm and the power difference scheme were used for the numerical approach. Numerical results generally agree with the previous experimental results though there are some uncertainties at far downstream and near the free surface due to the three dimensionality of the flow and surface waves. Without a baffle, the flow has basically the shape of the submerged plane wall jet with its upper boundary at downstream being sharply curved toward the free surface. For the flow with a baffle, recirculation flow patterns are observed at the upper inlet portion and at the backside of the baffle. For the case without a baffle, it was also confirmed that the ratio between the liquid level and the gate opening height is the most important parameter to determine the flow behavior.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.619-627
• /
• 2018

As ships become faster, larger and are required to meet higher standards, the importance of flow noise is highlighted. However, unlike in the aeroacoustics field for airplanes and trains (where flow noise is considered in design), acoustics are not considered in the marine field. In this study, analysis procedures for hull-induced flow noise are established to investigate the flow noise characteristics of a wave-piercing hull form that can negate the effect of wave-breaking. The principal mechanisms behind hull-induced flow noise are fluid-structure interactions between complex flows underneath the turbulent boundary layer and the hull. Noise induced by the turbulent boundary layer was calculated using wall pressure fluctuation and energy flow analysis methods. The results obtained show that noise characteristics can be distinguished by frequency range and hull region. Also, the low-frequency range is affected by hull forms such that it is correlated with ship speed.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.2
• /
• pp.21-30
• /
• 1990

Theoretical and experimental techniques to analyze the two-dimensional liquid motion in a tank are discussed. A Lagrangian FEM with a velocity correction procedure is introduced to describe incompressible free surface fluid flow. A mesh rezoning technique is used to prevent strong distortion of finite elements in the Lagrangian description. Model test technique for sloshing tank is developed using a hydraulic type bench tester. The influence of the variation in the exciting frequency and amplitude are observed for various fill depths. The results of theoretical calculations are compared with those of experiments.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1163-1170
• /
• 1992

A computer program was developed to analyze the two-dimensional unsteady incompressible viscous flow behind a rectangular bluff body between two parallel plates. The Peaceman-Rachford alternating direction implicit numerical method and Wachspress parameter were adopted to solve the governing equations in vorticity-transport and stream function formulation. The steady state flow and the vortex flow behind a rectangular bluff body in a chemical were investigated for Reynolds numbers of 200 and 500. The vortex shedding was generated by a physical pertubation numerically imposed at the center of the flow field for a short time. It was observed that the perturbed flow became periodic after a transient period.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.1
• /
• pp.71-82
• /
• 2002

A time-iterative compressible Navier-Stokes code is developed to analyze the flowfield of a two-dimensional ejector nozzle system. A parametric study has been made for two controlling parameters, duct to nozzle area ratio and nozzle pressure ratio. Results show that there is an optimum area ratio for an efficient pumping of secondary flow. At high area ratios, a freestream flow directly passes through the mixing duct without giving adequate pumping. While at low area ratios, jet boundary is acting as a blockage to incoming flow. The nozzle pressure ratio variation shows that the pumping rate increases as the pressure ratio increases provided there is no interaction between the shroud wall and the shock cell structure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.10-18
• /
• 2019

In this study, flow characteristics and the starting pressure of a center body diffuser (CBD) were analyzed at various center body (CB) positions and cone angles. According to the CB position, the location of oblique shock moved to the front from behind the CB cone with an increase in the flow momentum. Additionally, when a strong oblique shock occurred, the direction of supersonic flow was affected and induced to diffuser wall. As a function of different cone angles for the oblique shock, the starting pressure of the CBD was significantly affected.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.70-77
• /
• 2000

Supersonic Dual Bell Nozzle (SDBN) is an altitude-adaptive propulsion nozzle achieved only by a nozzle wall inflection. In order to investigate the altitude adaptive capability and the effectiveness of this nozzle concept, the present study addresses a computational work of the flow through SDBN. Several types of the SDBNs are tested for a wide range of the pressure ratio which covers from an over-expended flow to a fully under-expended flow at the exit of the SDBN. Axisymmetric, compressible, Wavier-Stokes equations are numerically solved using a fully implicit finite volume differencing scheme. The present computational results reveal that the base nozzle length affects the shock wave system occurring inside SDBN. For a quit wide range of the pressure ratio the flow separation occurs at the nozzle inflection point. It is found that the maximum thrust coefficient is obtainable for the correct expansion state at the exit of SDBN.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.969-978
• /
• 2008

In a linear cascade experimental apparatus, when it adopts only few blades as well as satisfies the periodic condition between blades, it gives several advantages in experiment. In this study, wall design on a cascade experimental apparatus is conducted to obtain the periodic condition on two blades installed within a passage of which the width is double pitch. The Mach number difference on the blade surface obtained with the periodic and wall condition is chosen as an objective function, and twelve design variables which are related to the wall shape are selected. A wall shape is designed using a gradient-based optimization method. Adjustment of range and weighting function are applied to calculate the objective function to avoid unrealistic evaluation of the objective function. By applying these methods, the computed results show same flow structures obtained with the periodic condition.