• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.31-37
• /
• 2001

This paper propose ZVS-HB type resonant DC/DC converter have earth different output characteristics using division ratio, not only a source division function but a resonant function and soft switching technique(ZVS, ZCS) instead of conventional source division capacitor. Circuit analysis generally described using normalized parameters most of characteristics with division ratio of source division capacitor. Also, this paper citified a rightfulness of characteristic analysis in comparison with a theoretical values and a experimental values obtain from experiment using Power-MOSFET.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.166-167
• /
• 2007

본 논문은 고주파 IH(Induction Heating) 조리기기의 전원으로 사용되는 인버터를 PI 제어기를 사용하여 듀티비를 가변시켜 출력을 최적 제어하는 회로를 제시하였다. 분석에 사용된 기본 인버터 회로는 Single-Ended Push-Pull (SEPP) 영전류 스위칭 공진인버터이며 실제 IH 조리기기의 동작을 구현하기 위해 입력단의 전원으로 220V 60Hz 정현파와 브리지 정류기, 평활 콘덴서를 사용하였다. 회로의 해석과 시뮬레이션을 위해 범용 시뮬레이션 툴인 Pspice를 이용하여 분석하였다. 향후, 제안된 제어방법은 유사한 IH 기기, DC-DC 컨버터, 인덕션 모터등의 시스템에 활용되리라 기대된다.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.741-749
• /
• 2021

This paper presents the current-fed type LLC AC to DC high frequency resonant converter capable of ZVZCS(Zero-Voltage and Zero-Current Switching). The current-fed type LLC AC to DC high frequency resonant converter proposed in this paper could operate not only in ZVS(Zero-Voltage Switching) operation by connecting the resonant capacitors(C₁, C₂) in parallel across the switching devices but also in ZCS(Zero-Current Switching) operation of the secondary diode. The ZVS and ZCS operations can reduce the turn-on loss of the switching devices and the turn-off loss of the secondary diodes, respectively. The circuit analysis of current-fed type LLC AC to DC high frequency resonant converter proposed in this paper is addressed generally by adopting the normalized parameters. The operating characteristics of proposed LLC AC to DC high frequency resonant converter were also evaluated by using the normalized control parameters such as the normalized control frequency(μ), the normalized load resistor(λ) and so on. Based on the characteristic values through the characteristics of evaluation, an example of the design method of proposed LLC AC to DC high frequency resonant converter is suggested, and the validity of the theoretical analysis is confirmed using the experimental results and PSIM simulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.2
• /
• pp.16-23
• /
• 2006

This paper presents a novel single-stage high frequency resonant inverter link type DC-DC converter using zero voltage switching with high power-factor. The proposed topology is integrated half-bridge boost rectifier as power factor corrector(PFC) and half-bridge high frequency resonant converter into a single-stage. The input stage of the half-bridge boost rectifier works in discontinuous conduction mode(DCM) with constant duty cycle and variable switching frequency. So that a boost converter makes the line current follow naturally the sinusoidal line voltage waveform. Simulation results have demonstrated the feasibility of the proposed high frequency resonant converter. Characteristics values based on characteristics analysis through circuit analysis is given as basis data in design procedure. Also, experimental results are presented to verify theoretical discussion. This proposed inverter will be able to be practically used as a power supply in various fields as induction heating applications, fluorescent lamp and DC-DC converter etc.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.49 no.2
• /
• pp.13-19
• /
• 2012

The techniques of 3d image processing have broadly used in the areas including movies, games, performances, exhibitions. In addition, increasing demands for practical uses have gradually extended to the areas of architecture, medicine, nuclear power plant. However, dominant techniques for 3d image processing seem to depend on multi-camera in which two stereo images are merged into one image. Also the pipeline has limitations to provide real-time 3d viewer in ubiquitous computing. It is not able to be applicable onto most general screens as well. In addition, the techniques can be utilized for the real-time 3d game play without a particular monitor or convertor. Hence, the research presented here is to aim at developing an efficient real-time 3d viewer using only mono camera which do not need post processing for editing as well.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.65-72
• /
• 2000

This paper proposes a Push type High Frequency DC-DC Converter using Zero Voltage Switching to reduce turn on and off loss at the switching instants. This paper has a advantage which is able to operating safely in load short, because DC reactor is connected with resonance reactor in order to supply a fixed safely in load short, because DC reactor is connected with resonance reactor in order to supply a fixed current with low ripple from DC power supply. The capacitor $(C_1, C_2)$ connected in switch are a common using as resonance capacitor and ZVS capacitor. The analysis of the proposed high frequency resonance DC-DC converter is generally described by using normallized parameter, and we has evaluated characteristic values which is needed to design a circuit. We conform a rightfulness of theoritical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.4
• /
• pp.56-64
• /
• 1997

최근 용접분야에서는 용접성능을 향상시키기 위하여 인버터회로를 용접기에 적용한 인버터 용접기에 관한 연구가 활발히 진행되고 있다,. 그러나 범용의 인버터 용접기의 경우 다이오드 정류기를 사용함에 저차의 전류고조파가 발생하고 시스템 역율을 저하시킨다. 따라서 본 논문에서는 인버터 아크 용접기의 역율개선을 위한 PWM 컨버터에 관하여 연구하여 입력전류의 저차 고조파를 저감하였고 전원전압과 동상으로 전원전류를 제어함에 의한 단위 역율형 인버터 용접기의 특성을 해석하였다. 또한 본 논문에서는 에너지 절약, 용접 특성, 역율, 사용율, 크기 및 부피 등의 관점에서 인버터 아크용접기의 응용연구 및 실험적 분석을 수행하였고 용접기 시스템에서 발생하는 전기적 노이즈를 억제하고 전력용 반도체 소자를 보호할 목적으로 새로운 노이즈 차폐변압기를 채택하였다. 이상의 전체시스템은 싱글칩 마이크로 프로세서를 이용한 디지털 제어기로 구현함으로서 제어기의 유연성과 기능의 다양화를 추구하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.90-97
• /
• 2001

A high frequency resonant inverter consisting of iliree unit Half-Bridge serial resommt inverter used as power source of induction heatmg at high frequency is presented in this paper. As a output [Dwer control strategy, sequencial time-sharing gate contml methcd is applied. This methcd is TDM(Time Division Multiplexing), which is broadly used with digital and analog signals transmission in communication system 1be analysis of the proposed circuit is generally described by using the normalized pararmenters. Also, the principle of basic operating and the its characteristics are estimated by the parameters such as switching frequency, load resistance. Also, according to the calculated characteristics value, a method of the circuit design and operating characteristics of the inverter is proposed. This paper proves the validity of theoretical analysis through the Pspice. This proposed inverter show that it can be practically used in future as power source system for induction heating application, DC-DC converter etc. r etc.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4975-4983
• /
• 2010

In this paper, the ordinariest and strongest simulator that many used to power electronics circuits and many different control technology can apply to more easily understand modeling the element, PSPICE and MATLAB are adapted a micro IGBT, a macro IGBT, PWM generator and to library moeling of validity of the Induction motor is interpreted. Micro IGBT model of demagnetization quality proved for modeling accuracy to through experiment, macromodel IGBT were simulated which the applied to voltage type PWM inverter to the cyclo-converter and induction motor of demagnetization.