• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.162-162
• /
• 2010

InAs 는 광전자 및 광통신 소자에 널리 이용되는 $In_xGa_{1-x}As_yP_{1-y}$ 화합물의 endpoint 로서, Heterojunction Field-Effect Transistors (HEMTs), Heterojunction Bipolar Transistor (HBT) 등에 중요하게 이용되고, 다양한 소자의 기판으로도 폭넓게 사용되는 물질이다. InAs 의 반도체 소자로의 응용을 위해서는 정확한 광 특성과 밴드갭 값들이 필수적이며, 분광타원편광분석법(ellipsometry) 을 이용한 상온 InAs 유전율 함수는 이미 정확히 알려져 있다. 그러나 상온에서는 $E_2$ 전이점 영역에서 여러 개의 밴드갭들이 중첩되어 있어, 밴드구조계산 등에 필수적인 InAs의 전이점을 정확히 정의하기 어렵다. 또한, 현재의 산업계에서 중요하게 여겨지는 실시간 모니터링을 위해서는 증착온도에서의 유전율 함수 데이터베이스가 필수적이다. 이와 같은 필요성에 의해, 22 K - 700 K 의 온도범위에서 InAs 의 유전율 함수와 밴드갭 에너지에 대한 연구를 수행하였다. InAs bulk 기판을 methanol, acetone, DI water 등으로 세척 한 뒤, 저온 cryostat 에 부착하였다. 분광타원분석법은 표면의 오염에 매우 민감하기 때문에, 저온에서의 응결 방지를 위해 고 진공도를 유지하며, 액체 헬륨으로 냉각하였다. 0.7 - 6.5 eV 에너지 영역에서 측정이 가능한 분광타원편광분석기로 측정한 결과, 온도가 증가함에 따라 열팽창과 phonon-electron 상호작용효과의 증가에 의해, 밴드갭 에너지 값의 적색 천이와 밴드갭들의 중첩을 관찰 할 수 있었다. 정확한 밴드갭 에너지 값의 분석을 위하여 2계 미분을 통한 표준 밴드갭 해석법을 적용하였으며, 22 K 의 저온에서는 $E_2$ 전이점 영역에서 중첩된 여러 개의 밴드갭들을 분리 할 수 있었다. 또한 고온에서의 연구를 통해, 실시간 분석을 위한 InAs 유전함수의 데이터베이스를 확립하였다. 본 연구의 결과는 InAs 를 기반으로 한 광전자 소자의 개발 및 적용분야와 밴드갭 엔지니어링 분야에 많은 도움이 될 것으로 예상한다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.2
• /
• pp.227-234
• /
• 2010

To investigate the flexural behavior of RC beams strengthened with carbon fiber sheets, 1 control beam and 8 strengthened beams(4 NU-beams without U-shaped band and 4 U-beams with U-shaped band) are tested. The variables of experiment are composed of the number of carbon fiber sheets and the existence of U-shaped band, etc. The experimental results showed that the strengthening system with U-shaped band controls the premature debonding and provides a more ductile failure mode than the strengthening system without U-shaped band. It can be found from the load-deflection curves that as the number of fiber sheets is increased, the maximum strength and the flexural rigidity is increased. The experimental results are compared with the analytical results of nonlinear flexural behaviors for strengthened RC beam. The proposed analytical method for strengthened beams is proved to be accurate by an experimental investigation of load-deflection curve, yield load, maximum load, and flexural rigidities in the pre- and post-yielding stages.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.6
• /
• pp.41-49
• /
• 2014

In order to investigation splitting bond strength of the deformed longitudinal reinforcing bars in the R C members strengthened laterally with the external steel-band, a total 9 sets of test re-bars with and without active confining force given by the external steel-band are pulled monotonically until failure. Test results indicate that the bond strength becomes higher with the increase in number of steel-band sets and their initial stress magnitude. This is due to the active confining force given by the steel-band, and passive confining forces given by the steel-band and transverse reinforcements, in which the passive confinement effect varies depending on the magnitude of active confining force. An equation to estimate the splitting bond strengths for the R C members strengthened laterally with the external steel-band is developed based on the several experimental results of the present study.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.7
• /
• pp.38-44
• /
• 2008

In this paper, we introduce an low complexity and low power IR-UWB (impulse radio ultra wideband) baseband transceiver for wireless sensor network. The proposed baseband, implemented by TSMC 0.18um CMOS technology, has a simple structure in which a simplified packet structure and a digital synchronizer with 1-bit sampler to detect incoming pulses are used. Besides, clock gating method using gated clock cell as well as customized clock domain division can reduce the total power consumption drastically. As a result, the proposed baseband has about 23K digital gates with an internal memory of 2Kbytes and achieves about 1.8mW@1Mbps power consumption.

• The KIPS Transactions:PartB
• /
• v.12B no.4 s.100
• /
• pp.379-386
• /
• 2005

This paper provides a rigorous theory for analysis of quantization effects and optimum filter bank design in quantized multidimensional subband filter banks. Even though subband filter design has been a hot topic for last decades, a few results have been reported on the subband filter with a quantizer. Each pdf-optimized quantizer is modeled by a nonlinear gain-plus-additive uncorrelated noise and embedded into the subband structure. Using polyphase decomposition of the analysis/synthesis filter banks, we derive the exact expression for the output mean square quantization error. Based on the minimization of the output mean square error, the technique for optimal filter design methodology is developed. Numerical design examples for optimum nonseparable paraunitary and biorthogonal filter banks are presented with a quincunx subsampling lattice. Through the simulation, $10\~20\;\%$ decreases in MSE have been observed compared with subband filter with no quantizers especially for low bit rate cases.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.344-352
• /
• 2020

Covertness and performance are very important design goals in the underwater communications. To satisfy both of them, we proposed efficient underwater communication model which combined multiband and direct sequence spread spectrum method in order to improve performance and covertness simultaneously. Turbo coding method with 1/3 coding rates is used for channel coding algorithm, and turbo equalization method which iterately exchange probabilistic information between equalizer and decoder is used for receiver side. After optimal threshold value was set in Rake processing, this paper analyzed the performance by varying the number of chips were 8, 16, 32 and the number of bands were from 1 to 4. Through the simulation results, we confirmed that the performance improvement was obtained by increasing the number of bands and chips. 2~3 dB of performance gain was obtained when the number of chips were increased in same number of bands.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.1-7
• /
• 2018

Suspension bridge cables made of high strength steel wires require periodical maintenance in accordance with the axial force of cable-band bolts, since the bolts in suspension bridges can undergo tension decrease due to creep of cable wires, bolt relaxation, load fluctuation, and cable re-arrangement, etc. Consequently, this study is aimed at investigating and subsequently evaluating the critical factors with respect to the bolt tension-decrease phenomenon in SR suspension bridge in Korea, based on field monitoring, theoretical studies, and field record management works. From the observation, it is interesting to note that the decrease in the bolt tension force is typically accompanied by plastic deformation of the zinc plating layers in the cable wires. In addition, a framework corresponding to generic methodologies to characterize the deformation in terms of the bolt tension-decrease and long-term history management has been developed in this exploratory study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.165-165
• /
• 2012

비정질의 Tantalum-indium-zinc oxide (TIZO) 박막 트랜지스터는 RF-sputtering 방법으로 증착되었으며 소결된 단일 타겟을 사용하였다. 증착당시 반응 가스는 알곤과 산소를 95 : 5로 섞어 반응성 스퍼터링을 진행하였으며, 1 mtorr에서 5 mtorr까지 다양한 공정압력에서 증착한 이 후 Furnace system을 통하여 $350^{\circ}C$의 온도로 1시간 동안 후열처리 공정을 진행하였다. 비정질 TIZO 박막을 활성 층으로 사용하여 제작한 박막 트랜지스터는 공정압력이 낮아짐에 따라 높은 이동도와 낮은 subthrehsold gate swing 보였다. 이러한 현상의 원인을 규명하고자 물리적, 전기적, 광학적 분석을 통하여 공정압력의 변화가 박막 트랜지스터 구동에 미치는 영향을 해석하였다. 우선 공정압력에 따른 TIZO 박막의 Ta, In, Zn, O 각각의 조성을 분석하기 위하여 Rutherford back scattering (RBS) 분석을 실시하였다. 또한 X-선 회절(X-ray diffraction)분석을 통해 열처리된 TIZO 박막은 공정압력에 따라 물리적 구조의 변화를 일으키지 않으며 모든 박막은 비정질상을 보이는 것을 확인하였다. 3.3eV의 광학적 밴드 갭은 기존에 보고되었던 비정질 산화물 반도체(InGaZnO, HfInZnO 등)와도 유사한 밴드갭을 가지고 있음을 확인하였다. 또한, spectroscopic ellipsometry (SE)분석을 통하여 전도대 이하 밴드 갭 내에 존재하는 결함상태 및 전도대에서 결함상태까지의 에너지 준위 그리고 공정압력에 따라 결함의 양과 발생되는 에너지 준위가 변화하는 현상을 관측하였다. 박막을 제조 할 때의 공정압력은 박막 내의 결함의 양 및 발생되는 에너지 준위의 변화를 야기하고 변화된 결함의 양과 발생된 에너지 준위에 따라 박막트랜지스터의 전기적 특성을 변화시킨다는 결과를 도출하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.140-144
• /
• 2004

The selectable dual band LNA usually uses common source transistor pair each input of which is selectively driven at a different frequency in a series resonant form. This paper analyzes the degradation in noise figures of the MOSFET common source pair with series resonance when it is driven concurrently at both inputs with different frequencies as a concurrent dual band LNA. Results of analysis will be compared with the measured noise figures of CMOS LNA with double inputs fabricated in 0.18 $\mu\textrm{m}$ CMOS process. Additionally, analyzing the contributions of FET channel noise and source noise from the LNA operating in the other band, this paper proposes optimum matching topology which minimizes the added noises for concurrent operation.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.198-201
• /
• 2000

Using the Finite-Difference Time-Domain (FDTD) method that analyzes the Maxwell equations in time domain, we simulated the characteristics of optical wave propagation and defect modes in two-dimensional photonic crystals composed of dielectric cylinders located on triangular, square, and honeycomb lattices. In particular, we investigated the properties of defect modes as the permittvity of the defects is varied. aried.