• Journal of the Korean Electrochemical Society
• /
• v.27 no.2
• /
• pp.73-79
• /
• 2024

As the use of fossil fuels has gradually increased, so has the emission of greenhouse gases such as carbon dioxide, leading to environmental problems. As a result, lithium-ion batteries (LiB) have emerged as the solution to this issue. To manufacture medium to large-sized lithium-ion batteries (LiB), it requires electrodes with high capacity and fast charging capabilities. Silicon (Si) is considered a next-generation anode with high-capacity properties, so, reduced graphene oxide (rGO) was compounded with Si@resorcinol-formaldehyde resin (RF) composite to prevent the volume expansion of Si. It was confirmed that the composite anode prepared exhibited improved capacity and enhanced stability.

• Journal of the Korean Institute of Gas
• /
• v.28 no.1
• /
• pp.59-64
• /
• 2024

In this study, we conducted research on a miniaturized transmission system suitable for ultra-compact electric vehicles, such as electric arts or small electric cars. While conventional electric vehicles eliminate multi-gear transmissions and control motor output or secure initial driving force through reducers, in vehicles like electric karts or compact electric cars, which have relatively small battery capacities, the driving range can be reduced or the motor can be stressed epending on the loading state. Therefore, in this study, we developed a low stage ratio 0.625 and high stage ratio 1.6 a two-stage transmission system that can change gears as needed, considering factors such as slope conditions and loading status, by applying the continuously variable transmission (CVT) mechanism. Based on the selected gear ratios, we designed the transmission and created a test rig to verify the power transmission efficiency of the developed transmission. Using the test rig, we varied the rotational speed and load of the transmission to confirm its power transmission characteristics and also examined the heat generation characteristics during shifting and operation. As a result, developed a two-stage transmission with a CVT structure.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2023

The cathode, which is one of the four major components of a lithium secondary battery, is an important component responsible for the energy density of the battery. The mixing process of active material, conductive material, and polymer binder is very essential in the commonly used wet manufacturing process of the cathode. However, in the case of mixing conditions of the cathode, since there is no systematic method, in most cases, differences in performance occur depending on the manufacturer. Therefore, LiMn₂O₄ (LMO) cathodes were prepared using a commonly used THINKY mixer and homogenizer to optimize the mixing method in the cathode slurry preparation step, and their characteristics were compared. Each mixing condition was performed at 2000 RPM and 7 min, and to determine only the difference in the mixing method during the manufacture of the cathode other experiment conditions (mixing time, material input order, etc.) were kept constant. Among the manufactured THINKY mixer LMO (TLMO) and homogenizer LMO (HLMO), HLMO has more uniform particle dispersion than TLMO, and thus shows higher adhesive strength. Also, the result of the electrochemical evaluation reveals that HLMO cathode showed improved performance with a more stable life cycle compared to TLMO. The initial discharge capacity retention rate of HLMO at 69 cycles was 88%, which is about 4.4 times higher than that of TLMO, and in the case of rate capability, HLMO exhibited a better capacity retention even at high C-rates of 10, 15, and 20 C and the capacity recovery at 1 C was higher than that of TLMO. It's postulated that the use of a homogenizer improves the characteristics of the slurry containing the active material, the conductive material, and the polymer binder creating an electrically conductive network formed by uniformly dispersing the conductive material suppressing its strong electrostatic properties thus avoiding aggregation. As a result, surface contact between the active material and the conductive material increases, electrons move more smoothly, changes in lattice volume during charging and discharging are more reversible and contact resistance between the active material and the conductive material is suppressed.

• Journal of Appropriate Technology
• /
• v.7 no.2
• /
• pp.127-135
• /
• 2021

To respond to the threat of global warming, countries around the world are promoting the spread of renewable energy and reduction of carbon emissions. In accordance with the United Nation's Sustainable Development Goal to combat climate change and its impacts, global automakers are pushing for a full transition to electric vehicles within the next 10 years. Electric vehicles can be a useful means for reducing carbon emissions, but in order to reduce carbon generated in the stage of producing electricity for charging, a power generation system using eco-friendly renewable energy is required. In this study, we propose a smart electric mobility operating system integrated with off-grid solar power plants established in Tanzania, Africa. By applying smart monitoring and communication functions based on Arduino-based computing devices, information such as remaining battery capacity, battery status, location, speed, altitude, and road conditions of an electric vehicle or electric motorcycle is monitored. In addition, we present a scenario that communicates with the surrounding independent solar power plant infrastructure to predict the drivable distance and optimize the charging schedule and route to the destination. The feasibility of the proposed system was verified through test runs of electric motorcycles. In considering local environmental characteristics in Tanzania for the operation of the electric mobility system, factors such as eco-friendliness, economic feasibility, ease of operation, and compatibility should be weighed. The smart electric mobility operating system proposed in this study can be an important basis for implementing the SDGs' climate change response.

• Journal of the Korean Society for Railway
• /
• v.19 no.3
• /
• pp.297-303
• /
• 2016

This paper introduces auxiliary power supply systems (APS) for railroad applications and proposes a new power conversion structure for highly-efficient and lightweight APS systems. The proposed structure focuses on an improvement of the power density in APS. It eliminates unnecessary power conversion stages in the conventional APS structure by modulating the dc/dc converter circuit and the structure of the system. The dc/dc converter circuit used in the proposed structure is based on a multi-level half-bridge converter, a widely used topology in railroad APS applications; a flying capacitor is newly added to the conventional circuit. The added capacitor is used not only to enhance the soft switching condition of the switches, but also so that the new pantograph will have a side voltage source of a battery charger in the APS structure. Since the battery charger uses the pantograph side voltage source in the proposed structure, rather than using the output of the main dc/dc converter in the conventional structure, the size and efficiency of the main dc/dc converter are reduced and increased, respectively. To verify the effectiveness of the proposed structure, simulation results will be presented with metropolitan transit APS specifications.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.53-53
• /
• 2017

연구목적: 국내 과일 산업의 한 단계 도약과 대외 경쟁력을 높이기 위해서는 수확작업의 기계화가 시급함. 이 연구는 국내외 과일 수확 기계화 현황과 문제점을 분석하고, 향후 수확작업 기계화 방향을 제시하고자 수행 수확기계 실용화 현황 및 고찰 (국내) 과일을 직접 수확이 아닌 수확 작업을 보조해주는 고지 작업기(수동형, 모터 진동형)와 고소 작업차가 대부분임. 수동형은 사과 감 등을 수확하지만, 작업능률이 낮고 작업자가 쉽게 피로하여 장시간 작업이 불가능하므로 실질적인 대안이 되지 못함. 진동형은 자체 동력을 이용하여 나무에 진동을 가하여 주로 대추 매실 등 소과류 수확에 이용되고, 수확능률은 우수하나 충격 손상이 많아 개선이 요구됨. 고소작업차는 동력원에 따라 충전식과 엔진식으로 구분되고, 충전식은 엔진식에 비해 진동 소음이 적어 쾌적하지만, 작업시간이 배터리 용량에 제한을 받음. 또한 작업대 작동방식에 따라 리프트형과 붐형으로 구분함. 리프트형은 리프트를 이용하여 작업대를 상하로 구동하는 방식으로 높은 위치의 과실 수확이 어렵고, 작업대 넓이 만큼의 작업 공간(과수간의 거리)이 필요함. 붐형은 필요한 곳으로 접근성이 우수하나 무거운 무게를 지탱하기 어렵기 때문에 본체를 무겁게 하거나 수시로 수확된 과일을 하차시켜야 함. (국외) 수확 후 가공되는 과일류와 포도 올리브 오렌지 매실 등 소과류 수확이 기계화되었지만, 사과 복숭아 등 신선과일은 아직도 외국의 값싼 노동자들에 의존하여 수확되고 있음. 현재 실용화된 수확 기계는 진동식 수확기계와 터널식 수확기계가 대표적임. 진동식은 집게형의 부착기를 나무 줄기에 고정한 후 트랙터 동력원으로 나무에 진동을 가하여 수확하고, 올리브 대추 등과 같은 소과류와 과피가 두꺼운 오렌지 등에 적용되고, 수확 작업능률이 매우 높으나 과일의 낙하 상처를 피할 수 없는 단점이 있음. 터널형은 규격화(과수 크기 및 형태, 재식거리)된 과수원에 잘 적응하도록 설계 제작되어, 과수 위를 지나가면서 내부에 설치된 진동장치와 컨테이너로 과일을 수확하고, 와인용 포도 수확기가 대표적임. 기계수확이 가능하도록 과수원 조성단계에서부터 재배양식(과수 좌우 및 전후 거리)을 기계의 제원(바퀴 간격, 작업부 간격 등)에 맞추어 재배함. 과일 수확로봇에 관한 연구는 활발하고 일부에서 실증시험단계에 있음. 결론: 구체적인 추진방향을 제시하면, 단기적으로는 과일 수확작업자의 작업편이성과 노동강도를 줄일 수 있도록 소형 저가 범용성이 우수한 보조기구/기계의 보급을 확대하고, 중장기적으로는 수확기계/수확로봇 개발을 위한 연구개발비 투자를 늘리는 동시에, 기계/로봇이 과수원에 잘 적응할 수 있도록 수형 재식거리 등 재배양식의 표준화가 추진되어야 함.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.11
• /
• pp.2218-2229
• /
• 2015

Recently Wi-Fi Alliance defined Wi-Fi direct, which can communicate through a direct connection between the mobile device anytime, anywhere. In Wi-Fi direct, all devices are categorized by group of owner (GO) and client. Since portability is emphasized in Wi-Fi direct devices, it is essential to control the energy consumption of a device very efficiently. In order to avoid unnecessary power consumed by GO, Wi-Fi direct standard defines two power management schemes: Opportunistic power saving scheme and Notice Of Absence (NOA) scheme. But, these two schemes do not consider the traffic pattern, so we cannot expect high energy efficiency. In this paper, we suggest an algorithm to enhance the energy efficiency of Wi-Fi direct power saving, considering the characteristics of multimedia video traffic. Proposed algorithm utilizes the statistical distribution for the size of video frames and adjusts the length of awake interval dynamically. Also, considering the inter-dependency among video frames, the proposed algorithm assigns priorities to video frames and ensures that a video frame with high priority is transmitted with higher probability than other frames with low priority. Simulation results shows that the proposed method outperforms the traditional NOA in terms with average delay and energy efficiency.

• The KIPS Transactions:PartC
• /
• v.17C no.6
• /
• pp.471-484
• /
• 2010

In the wireless communication systems, the power consumption of a mobile device is very important issue due to its battery limitations. Hence most of the standards for wireless networks including a mobile WiMAX system are supporting their own power saving mode in way that a mobile device is able to reduce its energy usage while in the mode. However, those standards just define the arrangement of special time intervals, called a paging listening interval, during which the device needs to receive the paging-related control messages, and they do not specify how to effectively reduce the power in many different network environments. This means the amount of power spent by the device is very dependent on the implementations of individual device-vendors, and undesirable paging loss may happen according to the channel conditions. To reduce unnecessary power usage and the risk of paging loss, this paper proposes the effective frequency/BS selection algorithm applicable to a mobile device operating in the power saving mode, which serves the device with better BS based on the tracking for channel variation. This algorithm consists of the channel estimation phase during each paging listening interval, the tracking phase for the measured results, the frequency reselection phase based on the tracking activity, and the preferred BS reselection phase. Thus the proposed method can improve the paging performance while the device is moving in the network. Also the simulation result shows that the presented scheme is superior to other candidates in energy efficiency due to the channel-adaptive frequency/BS selection.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.13-18
• /
• 2014

Sensor nodes are used for monitoring and collecting the environmental data via wireless sensor network. The wireless sensor network with various sensor nodes draws attention as a key technology in ubiquitous computing. Sensor nodes has very small memory capacity and limited power resource. Thus, it is essential to have energy efficient strategy for the sensor nodes. Since the sensor nodes are operating on the same frequency bands with ISM frequency bands, the interference by the devices operating on the ISM band degrades the quality of communication integrity. In this paper, the convolutional code is proposed instead of ARQ for the error control for the sensor network. The proposed convolutional code was implemented and the BER performance is measured. For the fixed transmitting powers of -19.2 dBm and -25dBm, the BER with various communication distances are measured. The packet loss rate and the retransmission rate are calculated from the measured BER. It is shown that the porposed method obtained about 9~12% and 12-19% reduction in retransmission rate for -19.2 dBm and -25 dBm respectively.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.456-464
• /
• 2007

This paper proposes a novel three-phase current-fed active clamp DC-DC converter for fuel cells. A single common active clamp branch is used to limit transient voltage across the three-phase full bridge and to realize zero-voltage switching(ZVS) in all switches. To apply for the power generation system current-fed type has been combined with the three-phase power conversion system. The proposed approach has the following advantages: an increase (by a factor of three) of input current and output voltage chopping frequencies; lower RMS current through the inverter switches with higher power transfer capability; reduction in size of reactive later components and the power conditioning system; better transformer utilization; increase of the system reliability. Therefore, the proposed three-phase current-fed active clamp DC-DC converter is appropriate for the boost type DC-DC converter for fuel cells and also applicable for the photovoltaic and battery charge system. The paper details the analysis, simulation and hardware implementation of the proposed system. Finally, experimental results with the proposed PWM strategy demonstrate the feasibility of the proposed scheme on a 500W prototype converter.