• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.3
• /
• pp.143-148
• /
• 2006

There are need to manage the water quality to supply an safety to consumer through pipe and reservoir the drinking water that produced in a clean water reservoir. However, a management of water quality and monitoring in reservoir have never been performed. Recently, the government has enforced standards of water quality. However, we have a inferior technology of water quality as compared with one in USA, Japan, Germany, etc. In case of water quality inspection and analysis equipments, sensor technology is very important to improve the water quality inspection and to develop the analysis equipments. In this paper, we analyze a law and a regulation for management of drinking water quality, and propose the measurement standards of drinking water quality in pH, conductivity, residual chloride, turbidity and water temperature. Then, we analyze electrode sensors that interference within pH, conductivity, residual chloride in interference experiment.

• Journal of Korea Water Resources Association
• /
• v.50 no.4
• /
• pp.263-275
• /
• 2017

Integrated numerical approaches with physically-based conceptualization are required for accurate urban inundation simulation. In this study, we described, applied and analyzed an integrated 1-dimensional (1D) sewerage system and 2-dimensional (2D) surface flow model, which was suggested by Lee et al. (2015). This model was developed based on dual-drainage concept, and uses storm drains as an discharge exchange spot rather than manholes so that interaction phenomena between surface flow and sewer pipe flow are physically reproduced. In addition, the building block concept which prevents inflows from outside structures is applied in order to consider building effects. The capability of the model is demonstrated via reproducing the past flooding event at the Sadang-cheon River catchment, Seoul, South Korea. The results show the plausible causes of the inundation could be analysed in detail by integrated 1D-2D modeling.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.19-24
• /
• 2010

Generally, slope behavior is analyzed by 2-dimensional creep model. Creep behavior shows the deformation variation as time goes by without stress increment. Convention 2-dimensional creep analysis does not have the term of stress variation, it means creep analysis could not figure out the relationship of shear strength variation according to the stress variation and displacement. The slope weight and shear strength is directly related and interlocked to the safety variation and displacement of slope, therefore, this phenomenon could be treated and analyzed as combining the hysteresis and creep, the iteration of this process will result in the slope safety. Furthermore, the combined analysis will be the slope analysis considering shear stress, displacement and shear strength with time variation. In real case, because the variation of shear stress and strength happen at the same time, they should be changed into safety factor which is function of them. This paper shows the 3-dimensional variation of unit weight of soil with hybrid analysis considering creep and hysteresis on the seepage and drainage of rainfall, futhermore variations of shear stress and strength which make the safety factor change.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.884-888
• /
• 2005

본 연구에서는 국내 적용되고 있는 여러 유출모형의 특성을 분석하여 도시화 전$\cdot$후 유역의 유출특성을 가장 잘 대변할 수 있는 모형을 선정하여 제시하고자 하였다. 국내의 경우 도시화 전$\cdot$후의 유출모의는 개발전을 자연하천유역으로 간주하여 Clark 모형이 사용되고 있으며, 도시화 후에는 도시하천유역에 주로 이용되고 있는 ILLUDAS 모형을 주로 이용하였으나, 최근 들어서는 도시화 전$\cdot$후 모두 Clark 모형을 적용하거나 도시화 후에는 SWMM모형이 사용되고 있다. 그리고, 과거 국내 주로 도시화 후에 적용되어왔던 ILLUDAS 모형은 미국의 Illinois라는 특정지역을 대상으로 개발된 모형이므로 우리나라의 모든 유역에 적용하는 것은 합리적이지 못하고 배수관망이 수리구조물을 포함하고 있는 경우 정확한 유출랑을 산정한다고 보기는 힘들다. 따라서 최근에는 미국에서 전지역적으로 권장되고, 국내에서도 이미 여러 연구를 통해 도시유출모형에서 다른 모형보다 우수함이 검증된 SWMM 모형의 사용이 증가되고 있다. 그러나, 각 모형마다 사용되는 매개변수와 모의과정의 차이가 있으므로 도시화 전$\cdot$후 다른 유출모형을 사용하는 방법은 도시화로 인한 유출특성의 변화뿐만 아니라 다른 모형의 적용으로 인한 모형적인 차이가 발생할 수 있다. 또한, 자연하천유역의 유출분석을 위해 개발된 Clark 모형은 도시화가 된 이후에 적용하기에는 배수관망과 맨홀 등의 분석이 불가하기 때문에 한계점을 내재하고 있다. 따라서, 도시화 전$\cdot$후의 유출특성의 변화를 정확하게 비교 예측하기 위해서는 서로 다른 모형의 적용으로 인해 발생할 수 있는 문제점 검토가 선행되어야 한다. 본 연구를 궁극적인 목적을 위해 도시유출모형의 자연유역에서의 적용성을 검토를 선행하였다. 자연하천 유역인 설마천 유역에 대해 Clark 모형과 SWMM 모형을 적용하여 비교 검토하였다. 연구결과 SWMM 모형의 자연유역 적용 가능성이 입증되었으며 추후 연구과제인 도시화 전$\cdot$후 유출특성 분석시 하나의 모형을 사용하여 유출모형간에 발생할 수 있는 차이를 제거할 수 있는 가능성을 확인할 수 있었다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.4
• /
• pp.59-66
• /
• 2007

The bridge crossing river is the one of the major factors causing backwater level rising. Furthermore, the bridges in the mountainous areas increase the flood damage in the upstream of the bridge due to the blockage by debris. In this research, the effects of debris to the magnitude of flood damage in the study river basin were simulated by using HEC-RAS and HEC-GeoRAS models. With assumption that the backwater caused by debris blocking the space between bridge piers is the only factor causing inundation, the unsteady flow simulation was carried out with various case studies. The potential inundation area with the overflow locations and volumes could be estimated as the results of simulation. However, the simulation results also reveal the limitations of inaccurate estimation of inundation area and depth. To overcome these hindrances, DEM and satellite images were applied to the simulation. By readjusting the inundation area using digital maps and satellite images and calibrating overflow volume and depth using DEM, the accuracy of simulation could be increased resulting more accurate flood damage estimation.

• Geotechnical Engineering
• /
• v.14 no.6
• /
• pp.45-56
• /
• 1998

In order to select a proper ground improvement technology and to assess the quality and rate of improvement in the soft deposits. it is essential to characterize in-situ properties of the soft marine clay layer that may have many thin silt or sand seams. In this paper, both piezocone and flat dilatometer tests were performed to characterize in situ properties of a marine clay. Both tests provided quite similar site classifications, and in both tests the penetration pore water pressure was the better indicator for the classification of marine clay layer, especially in which sand or silt seams are frequently interbedded. Undrained strengths determined by both the cone tip resistance and the excess pore water pressure measured from piezocone were very similar in clayey soil layers. And the untrained strength determined by dilatometer had an approximately average value of undiained strengths obtained from piezocone. In addition, the theoretical time factor that can consider pore pressure dissipation effect during cone penetration may provide a reliable estimation of the coefficient of consolidation, especially for a coastal site which includes many silt or sand fractions or seams.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1167-1175
• /
• 1994

The effects of the calculation method of surface runoff on the estimation of flood in urban drainage basin were analyzed in this study. In comparing with surface runoff methods. RUNOFF, ILLUDAS, SBUH and RRL were investigated. To route the flow in sewer/conduits EXTRAN was applied. The Kings Creek and Gray Haven drainage basin's measured data of rainfall and runoff were used in comparing the computed results. The results show that the greatest effect factor on surface runoff in urban small area is the concentration time. The results estimated by each model which are composed with EXTRAN show that the scheme for surface runoff gives considerable effect on the flood hydrograph in urban drainage system. RUN-EX method gives the most similar simulation results among the surface runoff models, and is more applicable for paved and unpaved basins than others.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1243-1251
• /
• 1994

The implicit finite difference program was developed to evaluate the relationship between time and consolidation ratio within the zone of vertical drain effective radius. In the evaluation, the excess pore water pressure was considered to dissipate in two directions, namely, vertical and radial flow direction. To calculate subsoil stress increments in the soil due to multi-step embanking, the foundation soil was assumed to be an isotropic and homogeneous elastic medium and the initial excess pore water pressure was estimated by using Skempton's parameters whose condition is plane strain and elastic phase of pore pressure response within the soft ground. Regarding to the settlement estimation, immediate and primary consolidation settlements were calculated. The secondary or delayed consolidation settlement was not considered. Numerically calculated excess pore water pressure and settlements were similar to the measured data in situ. Thus, this method can be used to predict the time-consolidation ratio of each layer treated by vertical drain method.

• Korean Journal of Plant Taxonomy
• /
• v.38 no.1
• /
• pp.17-29
• /
• 2008

Phylogenetic relationships were examined for 17 taxa of Lycoris by RAPD analysis. The length of the amplified DNA fragments ranged from 300 bp to 1,700 bp. 57 scorable RAPD markers were observed from PCR reactions with five random oligoprimers. The analysis by UPGMA sepatated the examined taxa of Lycoris into were clusters. First group was comprised of ten taxa of L. chinensis var. sinuolata, L. sanguinea var. koreana, L. uydoensis, L. flavescens, L. radiata var. pumila, L. radiata, L. squamigera, L. chejuensis, L. aurea and L. guangxiensis, second group of L. haywardii, L. sprengeri, L. rosea, L. straminea and L. houdyshii, third group of outgroup of Narcissus tazetta var. chinensis and Crinum asiaticum var. japonicum. From the viewpoint of cytological characters such as polyploidy and karyotype, the RAPD analysis was very useful to show the relationship among the intraspecific taxa of Lycoris.

• Journal of Educational Research in Mathematics
• /
• v.24 no.3
• /
• pp.359-374
• /
• 2014

Students' difficulties and errors in relation to mathematical proofs are worth while to say one of the dilemmas in mathematics education. The potential elements of their difficulty are scattered over the process of proving in geometry as well as algebra. This study aims to investigate whether middle school students understand the context of algebraic proof including literal expressions. We applied 24 third-grade middle school students a test item which shows a proof including a literal expression and missing the conclusion. Over the half of them responded wrong answers based on only the literal expression without considering its context. Three of them were interviewed individually to show their thinking. As a result, we could find some characteristics of their thinking including the perspective on proof as checking the validity of algebraic expression and the gap between proving and understanding of proof etc. From these, we also discussed about several didactical implications.