• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1288-1293
• /
• 2014

This paper proposes a new method to estimate the striking velocity for ballistic limit velocity in MIL-STD-662F. The method from MIL-STD-662F needs relative air density, drag coefficient, form factor, ballistic coefficient for estimating striking velocity. So precedent studies are essential. However, the new method can estimate striking velocity only using measured velocities and distance between the screen and the target. To prove new method, we compared estimation of striking velocity from both the new method and the method from MIL-STD-662F on the basis of datain PRODAS. The new method shows bigger errors in some velocity ranges. But it could still calculate ballistic limit velocity. It also shows smaller errors in most velocity ranges.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.9
• /
• pp.1661-1668
• /
• 2001

본고는 지뢰 방호복을 개발, 국산화하기 위해 먼저 방탄소재 구성방법에 관하여 실험한 결과이다. 기존의 여러 겹의 파라-아라미드(Para-aramid)나 단순히 파라-아라미드와 폴리 에틸렌 필름(Polyethlene film)을 조합한 소재구성과는 달리 케블라 파이버(Kevlar fiber)로 만들어진 펠트(felt)를 첨가하여 방탄원리 및 특성을 고려한 구성으로 방호복의 중량을 줄이면서 착용자로 하여금 유연성과 동작성을 향상시켜 임무수행과 안전성을 높일 수 있는 방호복을 개발하고자 하였다. 1) Para-aramid(내 충격열) + Flex-felt(충격 에너지 흡수) + Para-aramid(backface Polyethylene film(에너지 분산 극대)+Para-aramid(내 마찰열, backface순으로 소재를 배열함으로써 기존의 Para-aramed 36겹에 대하여 Para-aramid13겹, Polyethylene film 13겹, 그리고 펠트 1겹으로 동일한 방호성능을 얻었다. 2) 새로운 소재 구성 방법 에 의 한 방탄소재는 동일한 방호성능을 갖는 기존의 소재 구성 방법 에 따른 방탄소재 보다 중량에서 34-l9% ,더 가벼운 것으로 나타나 방호복 구성시 유연성이나 동작성에 유리 할 것으로 사료된다. 3) NIJ-STD-0101.03에서 의 Armor type II에 해당하는 시편 I의 방호한계속도로 구한 운동 에너지량은 154.4J Armor type III-A에 해 당하는 시편II의 방호한계속도로 구한 운동 에너지 량은 183.0J로 나타나 두 시편 모두 5m의 거리에서 M16Al지뢰의 0.032~0.044g사이 의 파편에 대해서 50%의 관통확률을 갖는 것으로 나타났다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.5
• /
• pp.629-637
• /
• 2016

This paper presents a ballistic limit velocity measurement using the support vector machine that classifies two classes, the partial penetration and the complete penetration, by generating a linear separating hyperplane that equally divides the classes. For the ballistic limit velocity measurement, the previous methods(MIL-STD-662F and NIJ-STD-0101.06) have required a large number of experiments that caused high cost and time. However, the proposed method is not only flexible, requiring 0.85 ~ 4.8 times fewer experiments but also reliable, providing less than 2 % difference in results compared to the previous methods. For its validation, live fire experiments were conducted using various thickness SS400 iron plates as a target and two different types of live bullets such as 5.56 mm M193 and 7.62 mm M80.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.4
• /
• pp.286-293
• /
• 2017

This paper presents ballistic limit velocity results of a variety of materials generally used in warships. Ballistic limit velocity is the velocity required for a projectile to penetrate a target with 50 percents of time and is widely used as a measure of armour bulletproofing. For this study, live fire experiments were implemented using AK-47 $7.62{\times}9mm$ mild steel core as a projectile as well as various thickness warship materials as a target. Also, methods of MIL-STD-662F, NIJ-STD-0101.06 and support vector machine were applied to measure the ballistic limit velocity and then their results were graphically analyzed for comparison. The minimum of their results was considered as the ballistic limit velocity in a conservative way.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.5
• /
• pp.322-329
• /
• 2021

Naval ships are designed to have a variety of active and passive systems to defend against enemy threats. One of the passive defense systems is to protect crew members and core equipment against the threat by using the outer plate of the equipment. This study was intended to deal with design methods against small arms ammunition and fragments. The Korea Institute of Machinery and Materials has measured the ballistic limit velocity of two types of high-tensile plate materials (AH36 and EH36) widely used in ships and offshore structures through tests in cooperation with various related organizations, and the result data is continuously accumulated. Based on the accumulated test results and data, such as mil test certificates of plate materials, it is intended to estimate the protection limit speed of high-tensile plates and to develop a simple calculating formula that can be used in the early design stage.

• Journal of the Korea Society for Simulation
• /
• v.30 no.1
• /
• pp.55-63
• /
• 2021

As a study on ballistic protection performance of a weapon system that is used in combat simulation, this paper aims to propose an improvement effect of the ballistic protection performance varying with incident angle of a bullet. For this, live-fire ballistic tests were performed to determine either complete penetration(CP) and partial penetration(PP) of three types of general armor plates made of uniformly rolled steel plates against a small caliber threat using 5.45 mm bullets with various speed. The major test parameter was the material of the weapon system and incident angle of the bullet with the target. Further, to quantitatively analyze the ballistic protection performance, three existing measurement methods were used for ballistic limit velocity. The test results showed that the ballistic protection performance with the incident angle of 30 degrees was 4% to 14% varying with the material of the armor plates greater than that of 0 degrees, which was approximately 1.1 times the performance improvement on average when compared to the conventional angle of incidence of the 0 degree. Those test results are expected to contribute to developing a more realistic combat simulation addressing the parameter improving the ballistic protection performance of an armor plate.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.177-184
• /
• 2016

This paper presents a strike velocity estimation using the recursive Bayesian filter that operates both correction and prediction models to probabilistically remove noises of sensors and accurately estimate the strike velocity during the real-time experiments. Four different types of bullets such as 5.56 mm M193, 7.62 mm M80, 5.45 mm 7N10 and 7.62 mm MSC were used to validate the proposed method. Compared to the existing method, the proposed method statistically results in higher stability of the strike velocity estimation as well as its reliability for the ballistic limit velocity computation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.691-697
• /
• 2011

In this study, the vessel collision protective structure and the vessel were modeled numerically and the quasi-static collision analysis was performed to evaluate the maximum protection capacity. In the modeling process of protective structure, the nonlinear behaviors of structure and the supporting conditions of ground including pull-out action were considered. In that of collision vessel, the bow of vessel was modeled precisely, because of the nonlinear behaviors were concentrated on it. For the efficient analysis, the mass scaling scheme was applied, also. To evaluate the differences and efficiency, the dynamic analyses were performed for the same model, additionally. Based on the obtained energy dissipation curves of the structure and the vessel, the moment that the collision force affected to the bridge substructures was determined and the maximum allowable collision velocity was evaluated. Because of the energy dissipation bound can be recognized clearly, this scheme can be used efficient in engineering work.

• Journal of the Korean Institute of Gas
• /
• v.10 no.3 s.32
• /
• pp.60-64
• /
• 2006

Explosion range and explosion characteristics of by product gas from carbon black manufacturing process were studied. About 75% of the by product gas were composed with water vapour and nitrogen. And the combustible component in the gas were hydrogen, methane, acetylene and carbon mono-oxide. Because of the combustible components in the by product gas there are explosion hazards in the gas handling process. Explosion range of the gas by experiment was from 17.1% to 70.7% and the value has considerable difference with the calculated value from Lechatelier law. Explosion pressure of the gas was $5.4kg/cm^2$ and the average explosion pressure rise rate was $39.2kg/cm^2/s$. Based on the experimental result we can expect that a explosion or fire accident during the handling the gas can make a severe loss, therefore there should be a explosion prevention or protection measures in the gas handling process.