• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.11
• /
• pp.83-88
• /
• 2011

The spectral field data on the observation planes inside a mode stirred chamber have been computed by using the FDTD method. They can describe the directional dependence of all supported modes in the reverberation chamber (RC). Correlation coefficients have been found to evaluate the stirring effects. The correlation coefficients were obtained and compared for three different sizes of stirrers and statistical uniformity was investigated.

• Journal of Korea Water Resources Association
• /
• v.33 no.5
• /
• pp.611-622
• /
• 2000

In this study, MODFLOW model is used to analyze the groundwater flow system of Seoguipo area in Cheju island, The final parameters of permeability coefficient and storage coefficient of target area can be obtained by trial and error method using the measured data of pumping rate as initial values. And it is found that the applicability for groundwater flow system is reflected well from the simulation result of the model. Seoguipo area spring water is thought to appear by relatively stable groundwater recharge below EL. 400m according to head distribution through the analysis of observed data considering topographic and geological characteristics, Lee's study(996), and the simulation result. Also it is known that point II, III, and VI show relatively large velocity vectors, and groundwater flows through the movement path which is distributed in various directions of I, II, III, IV, V, VI, and VIl form the result of velocity vector analysis using head distribution result values to analyze the groundwater flow path under unsteady flow condition.dition.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.2
• /
• pp.265-279
• /
• 1986

Ra=$10^{6}$, Pr=5에서 관열전도율과 두께가 변화할 때의 단일수평관에서의 자연대류 열전달에 관하여 유한차분법을 이용하여 해석적으로 연구하였다. .delta.$_{w}$ /d$_{o}$ =0.1에서 관열전도율이 높을수록 높은 온도와 높은 국소 누셀트 수를 나타 내며, .theta.=20。에서의 원주방향속도는 (r-r$_{o}$ )=0.08에서 최대가 되며 반경방향속 도는 (r-r$_{o}$ )=0.14에서 최대가 된다. 관외벽온도는 관 두께가 증가함에 따라 거의 유사하게 감소한다. $K_{w}$ /K$_{f}$ =75에서 각도변위가 증가함게 따라 국소 누셀트수는 현저히 증가하나 관 두께가 증가함에 따라서는 감소한다. .delta.$_{w}$ / d$_{o}$ =0.1에서 평균 누셀트수와 평균 온도는 무차원 열전도율이 증가함에 따라 $K_{w}$ /K$_{f}$ ＞15에서는 평균 누셀트 수는 서서히 증가하고 평균 온도는 거의 같 은 값을 가지며 지수함수로 표시할 수 있었다. $K_{w}$ /K$_{f}$ =75,50에서 평균 누 셀트수와 온도는 무차원 관 두께가 증가함에 따라 거의 직선적으로 감소되며 선형 함 수로 나타낼 수 있었다.

• Water for future
• /
• v.23 no.4
• /
• pp.435-444
• /
• 1990

The flow characteristics varying with the rate of the radius of curvature to width (Rc/B) in open channel bends are investigated with a simplified numerical model, briefly. Secondary flow velocity and transverse bed slope are formulated from the equations of moment of momentum and force balance analysis, respectively. The conservation equations of mass and streamwise momentum are simplified by depth integration and its solution could be obtained form explicit finite difference method. Three sets of computer simulation are executed. The rates of Rc/B adopted in simulations are 2.7, 5.4, 8.1 , respectively. The terms analyzed in this paper are secondary flow velocity, streamwise velocity, the path of maximum streamwise velocity, deviation angle, and mass-shift velocity.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.555-562
• /
• 2004

We propose a hybrid method combining the implicit with the explicit methods in order to reduce the calculation time and improve the convergence problem of the 3-dimensional finite-difference beam propagation method. The numerical simulation of a directional coupler is carried out by the proposed method. It is found from the simulation results that the calculation speed of our method is 10 times faster than that of direct solving techniques.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.6
• /
• pp.253-259
• /
• 2003

In this paper, the scattered field from a Pierson-Moskowitz sea surface assumed as the PEC by the Finite-Difference Time-Domain(FDTD) method was computed. A one-dimensional surface used to analysis scattering was generated by using the Pierson-Moskowitz model. Back scattering coefficients are calculated with different values of the wind speed(U) which determine configuration of the Pierson-Moskowitz sea surface. The number of surface realization for the computed field, the point number, and the width of surface realization are set to be 50, 8192, and 128k, respectively. In order to verify the computed values these results are compared with those of small perturbation methods, which show good agreement between them.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1243-1251
• /
• 1994

The implicit finite difference program was developed to evaluate the relationship between time and consolidation ratio within the zone of vertical drain effective radius. In the evaluation, the excess pore water pressure was considered to dissipate in two directions, namely, vertical and radial flow direction. To calculate subsoil stress increments in the soil due to multi-step embanking, the foundation soil was assumed to be an isotropic and homogeneous elastic medium and the initial excess pore water pressure was estimated by using Skempton's parameters whose condition is plane strain and elastic phase of pore pressure response within the soft ground. Regarding to the settlement estimation, immediate and primary consolidation settlements were calculated. The secondary or delayed consolidation settlement was not considered. Numerically calculated excess pore water pressure and settlements were similar to the measured data in situ. Thus, this method can be used to predict the time-consolidation ratio of each layer treated by vertical drain method.

• Journal of Korea Multimedia Society
• /
• v.13 no.3
• /
• pp.457-466
• /
• 2010

In this paper, we propose a new method for detecting digital forgery that identify interpolated region between digital composited images. For detecting the interpolation factor and the tampered regions, we perform two algorithms: The first algorithm is to estimate the interpolation factors using the differential equation for forgery image along the horizontal, vertical, and diagonal directions, respectively; The second algorithm is to scan the interpolation factors along each direction for detection areas as the mask of the optical window size($64{\times}64$) in order to find out the forgery region. A detection map of the forgery is classified with the magnitude of estimated interpolation factors into colors. This detection map can be used to find out interpolated regions from the tampered image. Experimental results demonstrate the proposed algorithms are proven on several examples. We also show the proposed approach is to accurately detect interpolated regions from digital composite images.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.4
• /
• pp.338-349
• /
• 1993

Most of numerical models for studying tide-induced residual currents (TIRC) were to dimensional depth averaged models which were confined to anlayze the horizontal structure of TIRC. In this study, TIRC occurring around a circular island was simulated with the three-dimensional spectral model which employed by the finite difference method in the horizontal direction and the expansion of basis function in the vertical direction. The main results of numerical experiment can be summarized as follows. Firstly. both topographic and nonlinear effect played an important role in the generation of TIRC. Secondly, when the currents were rotary clockwise. the horizontal structure of TIRC appeared to rotate in the same direction. These results were consistent with those of previous studies of two-dimensional numerical models.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.187-196
• /
• 2000

In this paper, stability analysis is carried out for the out of plane behaviors under compressive loads to the direction of the generator in anisotropic cylindrical shells. It is not easy to obtain the analytic solutions about the stability analysis of anisotropic cylindrical shells consisted of composite materials. For solving this problems, this paper used the finite difference method which is one of the numerical methods. Geometrical property of cylindrical shells transforms the compressive loads into the inplane behaviors. This paper studied the change of stiffness in the direction of the circumferential and stability of shells according to change of fiber angle, curvature, subtended angle and aspect ratio. From result of this study, anisotropic cylindrical shells under compressive loads to the direction of the generator vary greatly with respect to the change of the circumferential stiffness. Therefore, it will be more safe to strengthen the circumferential stiffness of anisotropic cylindrical shells under compressive loads.