• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.10
• /
• pp.63-71
• /
• 2009

The patch antennas with an array of pins with excellent radiation characteristics are investigated for several substrate thicknesses. The patch length of a pin array patch antenna for the maximum suppression of radiation in the horizontal plane decreases as the substrate thickness increases. The radiation in the horizontal plane of a pin array patch antenna is very small compared to that of a conventional patch antenna. The increase of forward radiation and the decrease of backward radiation of a pin array patch are obtained compared to those of a conventional patch antenna. The half-power beamwidth of E-plane radiation pattern of a pin array patch antenna is narrow compared to that of a conventional patch antenna so that the directivity is improved.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.2
• /
• pp.141-154
• /
• 2015

In general, conventional criticality analysis for spent fuel transport/storage systems have been performed based on the assumption of fresh fuel concerning the potential uncertainties from number density calculations of actinide nuclides and fission products in spent fuel. However, these evaluation methods cause financial losses due to an excessive criticality margin. In order to overcome this disadvantage, many studies have recently been conducted to design and commercialize a transportation and storage cask applied to the Burnup Credit (BUC). This study conducted an assessment to ensure criticality safety for reactor operating parameters, axial burn-up profiles and misload accident conditions, which are the factors that are likely to affect criticality safety when the BUC is applied to the dual-purpose cask under development at the KOrea RADioactive waste agency (KORAD). As a result, it was found that criticality resulting from specific power, changed substantially and relied on conditions of low enrichment and high burn-up. Considering the end effect in the case of high burn-up produced a positive-definite result. In particular, the increment of maximum effective multiplication factors due to misloading was 0.18467, confirming that misload is a factor that must be taken into account when applying the BUC. The results of this study may therefore be utilized as references in developing technologies to apply the BUC to domestic models and operational procedures or preventing any misload accidents during the process of spent fuel loading.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.146-150
• /
• 2017

In OFDM system, the out-of-band radiation of ensemble interferes with the adjacent ensemble and result in the reduction of receiving performance. So the reduction scheme of out-of-band radiation is very important. In this paper, a time-domain windowing method to reduce the out-of-band radiation is considered to DAB systems. We adopt the considered method to T-DMB(DAB mode-1) and AT-DMB Systems, and we get about 3-dB gains of out-of-band radiation. And also we show that the considered method doesn't reduce the BER performance.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.173-176
• /
• 2012

This paper introduces a novel horn antenna for circular polarization using a planar-type radiator. This antenna can be divided to two parts, microstrip antenna and square horn. The microstrip antenna has the role of feeder and polarizer of the horn antenna, and it is designed to stacked type having metal spacer for high gain, high isolation and wideband characteristic. Using the proposed antenna structure, the horn antenna needs not additional structure such as feeder and polarizer, and the size of it can be considerably reduced. The horn antenna has typical gain of 8dBi and 3-dB axial-ratio bandwidth around 4.9%.This antenna can widely used for various antenna system for mobile and satellite communication using circular polarization expecially in high frequency band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1211-1216
• /
• 2007

Yagi-Uda UHF RFID(Radio Frequency Identification) tag antennas with long reading range have been designed. According to ISO-18000, EIRP(Effective Isotropic Radiation Power) of reader and reader antenna is limited as 36 dBm. Therefore, the gain of a tag antenna should be high enough to extend the reading range. Yagi-Uda antenna has been applied to a UHF RFID tag antenna, and high gain and long reading range have been achieved. Three different of Yagi-Uda UHF antennas have been optimized to achieve the small size with low back-lobe patterns. The sizes, reading ranges and return loss of Yagi-Uda tag antennas are compared and measured.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.13-17
• /
• 2017

This paper presents an approach to enable a typical GPS receiver to be much less susceptible to intentional disruption such as jamming and change in link environment. In order for the GPS receiver to cope with jamming and to get adaptivity, a $4{\times}4$ beamforming antenna is designed using metamaterials. The design results show the antenna gain much higher than 5 dBi and the movable beam.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.280-286
• /
• 2006

Determination method of optimum feeding point for the PIFA type internal antenna for the mobile phone handset was studied. Fundamental theory is that radiated gain is basically depended upon the electric field strength between PIFA conductor and ground plane. Feeding point, slit configuration, material and structure of carrier are main factors fur the PIFA performances. It is shown that maximum electric field strengths of other feeding points decrease in -2dB to -10 dB than optimum point. Ansoft HFSS EM simulator was applied to determine the best feeding point for 2 models of Samsung Electronics mobile phone handset.

• Journal of Advanced Navigation Technology
• /
• v.28 no.2
• /
• pp.225-231
• /
• 2024

In this article, a new approach is presented to improve the unchangeable function of a ready-made millimeter-wave antenna system. By designing a metamaterial surface appropriate for the given geometry and fixed electrical characteristics of the device, the properties of the radiated fields of the RF product are changed to have directivity and higher antenna gain. Unlike other designs using periodic metamaterials for a single patch, an aperiodic metasurface is developed to handle two patches. For a higher received signal strength and a longer RF path in the 24 GHz-radio link, an aperiodic metasurface enhances the radiated fields by 10 dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.147-155
• /
• 2006

In this paper, we propose a new Mushroom-like PBG concepts for designing with forbidden frequency band-gap at low frequency. These design rules are based on enhancing the capacitance per unit area using modified top-patch of mushroom PBG with no increase on the overall thickness of the substrate board. Also, in this paper, a new approach to suppress the surface wave from antenna is proposed by embedding compact mushroom PBG in the substrate. Comparisons between the results from a conventional patch antenna to a patch antenna on a PBG substrate show that the reduction in the surface wave level is remarkable. This can be observed in the radiation pattern and the maximum gain. The maximum gain for reference patch antenna is $6.43dB{\imath}$ at 5.37 GHz, while the maximum gain for the patch antenna with normal mushroom and vane mushroom PBG is $7.24dB{\imath}\;and\;7.53dB{\imath}$at 5.14 GHz. The back radiation is also considerably reduced; this will lead, of course, to an increase in the antenna efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.906-912
• /
• 2008

We designed and implemented a 3-dimensional structure internal antenna which has volume less than 1.5 cc for mobile phone to improve efficiency and gain. Multiple bending for the resonance of small internal antenna derives reduction of gain due to cancellation of antenna current. In this study, the current cancelation was reduced by the minimization of antenna bending. And the helix element was applied for the purpose both compensation of short antenna length and action of radiation element. For the verification of this study, a 1.5 cc volume 3D antenna which was fabricated by the press method applied to the dual band mobile phone. Measurement showed that efficiencies and gains under the slide down and up were 27.73 %, 0.29 dBi for the GSM band and 46.84 %, 2.27 dBi for the USPCS band, and had good performance under the small antenna volume. H-plane radiation pattern showed omnidirectional for the both band.