• Elastomers and Composites
• /
• v.39 no.4
• /
• pp.274-280
• /
• 2004

Sorage modulus(G'), Impact and rebounding properties of polyurethane(PU), phylon(PH) and injection phylon(IP) foams were studied. The storage modulus of PU foam was dramatically increased with decreasing temperature. But the storage modulus(G') of IP and PH foams were not affected by temperature. The Impact force of PU foams was increased with decreasing temperature. But in the cases of IP and PH foams, the impact forces were not changed with temperature below $20^{\circ}C$. Impact farces of IP and PH foams were increased with the temperature above $20^{\circ}C$, but that of PU foam was not changed. Rebounding resilience of PU foam was lower than those of IP and PH foams from $-20^{\circ}C$ to $40^{\circ}C$.

• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.258-265
• /
• 2005

To study the compressive stress, recovery force and permanent strain of foams for footwear midsole, polyurethane(PU), phylon(PH) and injection phylon(IP) foams were repetitively compressed with constant compressive stress. Maximum compressive stress of PU did not decrease with repetitive compression on the constant compressive stress, but that of IP largely decreased. Engineering strain of foams were formed by repetitively compressing the three types of foam. The engineering strain of PU was smaller than that of IP and PH. Compressive stress and recovery force of IP and PH at certain strain were decreased with repetitive compression, but that of PU was not noticeably changed.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.246-246
• /
• 2004

본 연구는 발포유리 조성물 및 이를 이용한 발포유리 전구체의 제조방법에 관한 것으로, 구체적으로 알칼리 히드록시, 실리카 및 붕산으로 이루어진 발포유리 조성물 및 이를 이용한 발표유리 전구체의 제조방법에 관한 것이다. 본 연구에 의해 제조된 발포유리 전구체는 발포제의 사용없이 우수한 발포성능을 발휘하며, 특히 저온에서 발포성능을 나타내어 방열 및 방음용 유리 발포체로 사용할 수 있으며 각종 도료 및 페인트에 첨가하여 사용할 수 있다.(중략)

• Elastomers and Composites
• /
• v.39 no.3
• /
• pp.186-192
• /
• 2004

Compression and rebounding properties of IP(injection phylon), PH(phylon) and PU(polyurethane) foams were studied. The compression stress, rebounding stress, loss compression energy and storage compression energy of foams were decreased with increasing hardness of foams. The compression stress, loss compression energy of IP foams were lower than those of PH and PU. Rebounding stress and storage compression energy of PU foams were higher than those of IP and PH. The compression stress and rebounding of PH foam were lower than those of IP and PU.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.52-60
• /
• 2001

Physical properties of foams depend on the density of foams, Physical properties of base polymers, open ceil contents, and cell structures including the size, size distribution, shape of ceil and the thickness of membrane and strut. The density of foam is affected by raw materials, concentration oi crosslinking agent and blowing agent and process parameters such as processing technique and condition. Ethylene vinyl acetate copolymer(EVA) foam is a crosslinked cellular material. The foaming characteristics and physical properties of EVA foam are affected by decomposition rate of blowing agent. In this study, the decomposition rate of blowing agent and crosslinking rate, foaming characteristics and physical properties of foams were evaluated. The slow decomposition rate of blowing agent results in low density foam, good shock absorption property and uniform cell size distribution compared to the high decomposition rate of blowing agent.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.679-690
• /
• 2001

High resilience PU foams were prepared with polyether type cell opener. The influences of cell opener concentration on the kinetics, rheology, structural stability morphology and open cell content of the obtained foam were investigated and the role of cell opener during cell opening was determined. And mechanical properties as a function of cell opener concentration were studied. It was observed that urea formation reaction was delayed due to high hydrophilicity of cell opener The decrease of viscosity and the increase of tan $\delta$ were confirmed with increasing cell opener concentration so that the resulted foam had low structural stability and high open cell content. The deterioration of matrix and uniform dispersion of hydrogen-bonded urea in matrix with cell opener concentration was revealed by SEM analysis. As a result, elastic properties of the foam matrix were decreased due to high hydrophilicity of cell opener during the preparation of high resilience polyurethane foam and foam with high open cell content resulted. Hardness, tensile strength, tear strength, elongation of foam were decreased with increasing cell opener concentration.

• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.242-248
• /
• 2005

To study the fatigue properties of three type of foams for footwear midsole, polyurethane(PU), phylon(PH) and injection phylon(IP) foams were prepared with different hardnesses. Three types of foams were repetitively compressed for 50,000 cycles at 50 rpm. Cell shapes of foams were deformed with repetitive compression. The extent of cell deformation of IP was larger than those of PH and PU. Permanent strain of foam was made by repetitively compressing the foam, and the extent of IP was larger than those of PU and PH. Maximum compression forces of three types of the foams were decreased with the repetitive compression, and IP had the largest decrease in compression load of foam with compression. Decreases in maximum compression force of three types of foams were increased with increase of the hardness of foam.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.8-13
• /
• 2010

The physical properties of polymeric foams depend on the density of foams, physical properties of base polymers, the content of open cells, and cell structures including the size and its distribution, the shape of cell, and the thickness of skin layer. The foam density is affected by the chemistry of raw materials, the concentration of crosslinking agent and the blowing agent as well as the operating parameters during production process. In this study, the basic formulations of foams are composed of polyester polyol, MDI, amine catalyst, tin catalyst, silicone surfactant, and water. Cross-linking density of polyurethane was increased by using chain extenders. Also, the mechanical properties of polyurethane foam were improved by using the inorganic fillers (silica 1,2 and talc 1,2) having different $SiO_2$ contents and particle sizes. We investigated the properties of modulus, tensile strength, compressive strength and hardness of foams obtained by changing kind of inorganic filler and chain extender, and observed the distribution of inorganic filler as well as variation of cell size within the foams by electron microscopy.

• Composites Research
• /
• v.36 no.5
• /
• pp.297-302
• /
• 2023

There are several methods for shaping foams, but the most commonly used methods involve the use of resin mixed with a foaming agent, which is then foamed under high temperature and pressure in the case of compression foaming, or foamed under high temperature without applying pressure in the case of atmospheric foaming. The polymers used for foaming require design and analysis of optimal foaming conditions in order to achieve foaming under ambient pressure. Environmentally friendly bio-based polymers face challenges when it comes to foaming on their own, which has led to ongoing research in blending them with resins capable of traditional foam production. This study investigates changes in the characteristics of bio-based polymer-EVA blend foams based on variations in the content of bio-based polymers and explores the optimal foaming conditions according to crosslinking. The correlation between foaming characteristics and mechanical properties of the foams was examined. Through this research, we gained insights into how the content of bio-based polymers affects the properties of foams containing bio-based polymers and identified differences between ambient pressure and high-pressure foaming processes. Additionally, the feasibility of commercializing bio-based polymer-EVA composite foams was confirmed.

• Applied Chemistry for Engineering
• /
• v.31 no.1
• /
• pp.30-35
• /
• 2020

In this study, polyurethane-silica composite foams were synthesized to analyze thermal insulation characteristics and mechanical properties. In order to synthesize polyurethane-silica composite foams, polyester-silica composite polyols were first synthesized via a polymerization reaction with silica sol, dicarboxylic acid and glycol in monomer state. Physical properties of polyurethane-silica composite foams synthesized using the composite polyols were analyzed. From the thermal conductivity analysis, no significant differences among HPUF0, HPUF1, HPUF3 and HPUF5 were found. The compressive strength of polyurethane-silica composite foams increased as the silica content increased. The mechanical property of HPUF5 was also about 25% higher than that of HPUF0.