• Cement
• /
• s.12
• /
• pp.36-46
• /
• 1965

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.23-27
• /
• 2004

The $Al_xTa_{1-x} (x=0.0{\~}1.0)$ alloy thin films were deposited by RF-magnetron sputtering system, and the crystal quality, surface morphology, and electrical properties were examined using XRD, AFM, 4-point probe techniques in this study. The thin films were grown according to the alloy compositions first, and the effects of film thickness and mask patterns were investigated afterwards. Also, the heating characteristics were examined by heat controller. The obtained results showed that the high electrical resistivity was obtained for Al content $x=6.63at\%$, and the even higher resistivity was accomplished for the samples with smaller thickness and narrower width. The heating temperature demonstrated the identical trend to the electrical properties, and the highest heating temperature ($400^{\circ}C$) and output power ($12.6W/cm^2$) were obtained for the sample with Al content $x=6.63\%$, film thickness d=500 nm, film width w=1.5 mm.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.05a
• /
• pp.129-132
• /
• 1995

상압의 유동층반응기 (0.1 m-i.d x 1.6 m-high) 에서 호주탄을 수증기와 공기를 사용하여 가스화 하였다. 또한 반응기에서 촉매효과를 고찰하기 위해 $K_2$SO$_4$+Ni(NO$_3$)$_2$ 촉매를 호주탄에 담지하여 가스화반응을 수행하였다. 생성가스조성, 생성가스량, 탄소전환율, cold gas efficiency 및 발열량 등에 대한 유동화속도 (2~5U$_{mf}$), 반응온도 (750~90$0^{\circ}C$), 공기/석탄 비 (1.6~3.2), 수증기/석탄 비 (0.63~l.26)의 영향을 조사하였다. 탄소전환율, 생성 가스량, 생성가스 발열량 및 cold gas efficiency 는 유동화속도와 반응온도의 증가에 따라 증가하였다. 공기/석탄 비가 증가함에 따라 탄소전환율과 생성가스량 및 cold gas efficiency 는 증가하지만 생성가스 발열량은 감소하였다. 수증기/석탄 비의 증가에 따라 발열량, cold gas efficiency 및 생성가스량은 증가하였으며, 탄소 전환율은 거의 일정하였다. 촉매 가스화반응에서 유동화속도, 반응온도, 공기/석탄 비 및 수증기/석탄 비의 증가에 따라 탄소 전환 율, 생성가스량, 생성가스 발열량 및 cold gas efficiency 는 크게 향상됨을 알 수 있었다.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.324-332
• /
• 2017

The comparative experiments were conducted for single span greenhouses where cucumbers were cultivated to analyze the effect of heating between a carbon fiber electric heating element heater and an oil hot air heater in terms of the inside climate, energy consumption and plant growth. In order to analyze the effect of heating capacity, 6, 9, and 16 kW of electric powers were supplied to the electric heating element for same setting temperature of 15?. As a result, as the heating capacity increased, the number of ON-OFF cycles of the electric heating element and the temperature inside the greenhouse increased proportionally. In the comparison of two heaters, it was shown that the temperature and relative humidity distributions of the electric heating element installed greenhouse was much uniform than those of the oil hot air heater installed greenhouse. The heating energy consumptions during the heating period of 79 days were 867L for the oil hot air heater and 8,959 kWh for the electric heating element heater, and the heating costs were 607 and 403 thousand won respectively. In the electric heating element installed greenhouse, the cucumber growth was slightly better and the yield was 4.3% higher than those of the oil hot air heater installed greenhouse, but there were no statically significant difference in the cucumber growth and yield between greenhouses.

• Electrical & Electronic Materials
• /
• v.6 no.4
• /
• pp.311-317
• /
• 1993

발열체 소자에 있어서 발열체의 방사스펙트럼과 피가열체의 흡수스펙트럼을 일치시키는 문제는 효과적인 가열을 위하여 매우 중요한 연구과제이다. 본 연구는 재료의 합성기술과 열처리기술을 이용하여 PTC 서머스터의 R-T특성은 그대로 유지시키면서 원적외선 방사특성을 증대시키기 위한 것이다. 이를 위하여 BaTiO$_{3}$+1.67Al$_{2}$O$_{3}$+3.75SiO$_{2}$+1.25TiO$_{2}$을 기본조성으로 하고 여기에 첨가제로서 Sb$_{2}$O$_{3}$와 MnO$_{2}$를 선정하여 이의 첨가량과 소결온도 그리고 소결온도구배를 파라메터로한 시편을 제작하였으며 각 시편의 IR특성과 R-T특성등을 측정 검토한 결과 파장 4.5-14.5[.mu.m]범위에서 방사율 0.8이상의 고효율 원적외선 방사특성을 얻었다.

• Composites Research
• /
• v.33 no.6
• /
• pp.395-400
• /
• 2020

In this paper, we manufactured silsesquiaznae (SSQZ)-coated carbon nanotube (CNT) surface heating elements, which allowed stable heating at high temperatures. The prepared composite sheet was confirmed by FE-SEM that the SSQZ fully coated the surface of CNT sheet. Furthermore, it was also confirmed that the silicon carbonitride (SiCN) ceramic formed by heat treatment of 800℃ have no defects found and maintain intact structure. The CNT/SiCN composite sheet was able to achieve higher thermal stability than raw CNT sheets in both nitrogen and air atmosphere. Finally, the CNT/SiCN composite sheet was possible to heat up at a temperature of over 700℃ in the atmosphere, and the re-heating was successfully operated after cooling.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.1
• /
• pp.27-32
• /
• 2014

This study analyzed the fundamental characteristics of concrete according to a ternary system mixing in order to reduce hydration heat of mass concrete and to improve early age strength. The results are as follows. The fluidity of unconsolidated concrete satisfied the target scope regardless of the binder conditions. When the replacement ratio between FA and BS increased, the slump of low heat-A mix and low heat-B mix increased, and air content was not affected by the change of binders. As for setting time, low heat cement mix had the fastest regardless of W/B, and high early strength low heat mix achieved 6 hours' reduction compared with low heat-B mix at initial set, and 12 hours' reduction at the final set respectively. As for the simple hydration heat, the low mix peak temperature was the highest and low heat-B mix had the lowest temperature. And high early strength low heat mix was similar with that of low heat-B. The compressive strength of hardened concrete had similar strength scope in all mixes except for low heat-B mix at early ages, and had unexceptionally similar one without huge differences at long-term ages.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.17-24
• /
• 2024

The characteristics of low-heat concrete, mixed with ground blast furnace slag and ferronickel slag aggregate, were analyzed. Moreover, the applicability of this concrete for mass concrete in LNG storage tanks was examined. Initially, the study investigated the characteristics of fresh and hardened concrete. Subsequently, the temperature rising curve was obtained. Utilizing the obtained parameters from the curves, a series of thermal stress analyses for the LNG storage tank were conducted to assess the risk of cracking. The results confirmed that concrete mixtures incorporating ground blast furnace slag and ferronickel slag aggregate not only exhibited sufficient workability but also achieved a compressive strength of approximately 40 MPa within 28 days. Furthermore, the concrete demonstrated a lower terminal heat rise and a faster heat generation rate compared to low-heat Portland cement concrete. An analysis of thermal stress in various sections of the LNG tank validated a low risk of cracking.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.84-90
• /
• 2016

Various form of membrane structures are being built in recent years. However, there is no appropriate fire proofing standards which can be applied each specific membrane structures. Therefore, existing fire protection standards are in establishment state and they need to be revised. In the current study, commonly used membrane materials(ETFE, PVF, PTFE) has been selected to investigate its fire resistance behavior with the change of fire duration time. In addition to this, heat generation rate of the membrane materials in correlation with the height of membrane has been investigated. And these fire combustion characteristics of membrane materials can be used in future practice for the fire prevention regulations of membrane structures.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.343-344
• /
• 2010

화석연료의 고갈로 인하여 친환경 자동차에 대한 연구와 상용화가 급속도로 진행되면서 점점 대형 차종으로 그 범위가 넓어지고 있다. 대형 차종에 적용되는 전기동력 시스템의 MCU(Motor Control Unit), GCU(Generator Control Unit), DC/DC 컨버터 등과 같은 전장품도 그 용량이 커지면서 상용화를 위해 효율적인 측면도 많이 부각되지만 스위칭 소자, 변압기, 초크, 다이오드 등에서 동작으로 인해 열이 발생하고 제품의 구조상 밀폐된 공간에 장착이 되기 때문에 발열로 인한 동작의 신뢰성과 제품의 내구성에 큰 영향을 미치게 된다. 그중 가장 발열이 심한 IGBT(Insulated Gate Bipolar Transistor) 등과 같은 스위칭 소자에서 발생하는 열을 효과적으로 냉각시키기 위해 수냉구조가 필수적이며 동일한 조건의 수압, 유량에 보다 높은 방열특성을 가지기 위해 냉각구조에 대한 해석이 제품을 개발 전에 선행되어야 한다. 본 논문에서는 유로의 냉각핀 형상과 유로 구조에 따라 방열특성이 어떠한 차이가 있는지 시뮬레이션 프로그램을 통하여 비교하고, 모사발열체를 이용한 방열부의 냉각 성능 시험과 다이나모 환경의 최대 출력 시험을 통하여 방열 특성을 확인하였다.