• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.11a
• /
• pp.23-29
• /
• 1999

Experimental studies are conducted to investigate the flame stability and the thermal/fuel NOx formation characteristics of the low calorific value (LCV) coal derived gas fuel. Synthetic LCV fuel gas is produced by mixing carbon monoxide, hydrogen, nitrogen and ammonia on the basis that the thermal input of the syngas fuel into a burner is identical to that of natural gas. The syngas mixture is fed to and burnt with air on flat flame burner. With the variation of the equivalence ratio for specific syngas fuel, flame behaviors are observed to identify the flame instability due to blow-off or flashback and to define stable combustion range. Measurements of NOx content in combustion gas are made for comparing thermal and fuel NOx from the LCV syngas combustion with those of the natural gas one. In addition, the nitrogen dilution of the LCV syngas is preliminarily attempted as a NOx reduction technique, and its effects on thermal and fuel NOx production are discussed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.4
• /
• pp.304-311
• /
• 2006

Experiments on evaporative spray cooling on the square plate heaters with plain or micro-porous coated surfaces were performed in this study. Micro-porous coated surfaces were made by using DOM [Diamond particle, Omegabond 101, Methyl-Ethyl-Keton] method. In case of purely air-jet cooling, the micro-porous coating doesn't affect the cooling capacity. In spray cooling three different flow patterns (complete wetting, evaporative wetting, dryout) are observed on both plain and micro-porous coated surfaces. The effects of various operating conditions, such as water flow rate, particle size, and coating thickness were investigated on the micro-porous coated surfaces. It is found that the level of surface wetting is an important factor to determine the performance of spray cooling. It depends on the balance between absorbed liquid amount by capillary force over porosity and the evaporative amount. The micro-porous coated surface has largest cooling capacity, especially in the evaporative wetting zone. It is found that the effects of liquid flow rate and coating thickness are significant in evaporative wetting zone, but are not in complete wetting and dryout zones.

• Journal of the Korean Society of Safety
• /
• v.34 no.3
• /
• pp.15-20
• /
• 2019

As industry is progressing and standards of living are improved, the demand of electrical energy is expected to grow 8-9% annually. Therefore, the importance of electrical fire prevention technology with the ability of the power supply is being emphasized. According to the statistics of fire in Korea, fire occurred about 45,000 cases annually, and electrical fire possessed about 20%. The electrical fire by poor contact has increased gradually, can be connected as great fire to secondarily induce short circuit and earth fault. Then analysis of heating causes of electrical connections between copper and copper alloy is needed. Also, detection and analysis algorithm of oxide at copper alloy are necessary. In this research, in order to understand the characteristics of oxide growth with rising resistance and heating, it is demonstrated that the oxide at electrical connections can cause fire due to arcing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.116-121
• /
• 2019

Hexagonal boron nitride particles (s-hBN) modified with 3-aminopropyl triethoxysilane (APTES) were used for the preparation of silicone composite materials. The microstructure of the composite materials was observed, and the thermal conduction and mechanical characteristics of the composite sheets were studied based on the compositions and microstructures. When a small amount of s-hBN particles was used, the thermal conductivity of the composite improved as a whole, and the tensile strength of the sheet also increased. The thermal conductivity and tensile strength of the composite in which a small amount of carbon fiber was added along with s-hBN were further improved. However, the use of carbon nanotubes with structural characteristics similar to those of carbon fiber resulted in lower thermal conductivity and tensile strength. Elastic silicone composites exhibiting 2.5 W/mK of thermal conductivity and a low hardness are expected to be used as thermally conductive interfacial sheet materials.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.10
• /
• pp.44-51
• /
• 2020

We studied the heating characteristics of a whirling spindle. This spindle is an important component of a whirling machine for turning a ball screw shaft. In the manufacturing process for a conventional ball screw shaft, a single tool is used to form a spiral in a lathe machine tool. Thereafter, a high-frequency heat treatment process is performed. Recently, a whirling-type cutting method has emerged. This method can perform hard turning in the rotating direction of the spiral portion of the ball screw shaft by rotating and mounting multiple tools. The whirling method can be applied to the heat-treated material. In this study, an experimental apparatus was constructed to analyze the whirling spindle. The experiment proceeded in four steps. The rotating speed of the whirling spindle was set to ISO random and sequential rising conditions. Cooling and non-cooling modes in the cooling jacket were tested. As a result of the above experiment, the heating characteristics of the whirling spindle were derived.

• Journal of the Society of Disaster Information
• /
• v.18 no.1
• /
• pp.163-172
• /
• 2022

Purpose: To secure efficient thermal management technology for Li-ion batteries, the applicability of the system applied with single-phase immersion technology was checked through an experiment. Method: Using JH3 pouch cells produced by LG-Chem, Korea, A 14S2P module was manufactured and immersed in a vegetable-based cooling fluid produced by Cargill, USA, and then charged and discharged at a rate of 0.3C to 1C to check the heat distribution. Result: It was possible to manage and there was no change in the molecular structure of the immersion solution. Conclusion: It was confirmed that the immersion cooling method can be applied to the thermal management of Li-ion batteries.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.37-43
• /
• 2022

In this study, we investigated the optical, electrical and exothermic characteristics of ITO/Ag/ITO multilayer structures prepared with various Ag thicknesses on quartz and PI substrates. The transparent conducting properties of the ITO/Ag/ITO multilayer films depended on the thickness of the mid-layer metal film. The ITO/Ag (14 nm)/ITO showed the highest Haccke's figure of merit (FOM) of approximately 19.3×10^-3 Ω^-1. In addition, the exothermic property depended on the substrate. For an applied voltage of 3.7 V, the ITO/Ag (14 nm)/ITO multilayers on quartz and PI substrates were heated up to 110℃ and 200℃, respectively. The bending tests demonstrated a comparable flexibility of the ITO/Ag/IT multilayer to other transparent electrodes, indicating the potential of ITO/Ag/ITO multilayer as a flexible transparent conducting heater.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.881-891
• /
• 2008

The purpose of the present study is to investigate the influence of seasonal temperature variation on the thermal stresses in roller compacted concrete dam(RCD) structures. Using the finite element code, DIANA performs 2-D transient temperature and resultant stress analysis for RCD. Time variability of the mesh geometry is considered in order to simulate successive phases of the structure's construction. The main analysis variables are construction sequence, concrete temperature and ambient temperature. The results show principal tensile stress of hot-weathering concrete is higher than that of cold-weathering concrete. In some case the index of thermal cracking excesses 1.0, RCD also needs thermal management on placing temperature according to weather condition.

• Journal of Industrial Technology
• /
• v.43 no.1
• /
• pp.15-23
• /
• 2023

Lithium-ion batteries are predominantly employed in electric vehicles and energy storage devices, offering the advantage of high energy density. However, they are susceptible to efficiency degradation when operated at high temperatures due to their sensitivity to the external environment. In this study, we conducted experiments using an indirect cooling method to prevent thermal runaway and explosions in lithium-ion batteries. The results were validated by comparing them with heat transfer simulations conducted through a commercial finite element analysis program. The experiments included single-cell exothermic tests and cooling experiments on a battery pack with 10 cells connected in series, utilizing 21700 lithium-ion batteries. To block external temperature influences, the experimental environment featured an extrusion method insulation in the environmental chamber. The cooling system, suitable for indirect cooling, was constructed with copper tubes and pins. The heat transfer analysis began by presenting a single-cell heating model using commercial software, which was then employed to analyze the heating and cooling of the battery pack.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.253-253
• /
• 2016

최근 세계적으로 대체 에너지는 중요한 이슈가 되고 있으며 그 중 열전 재료는 유망한 에너지 기술로서 주목 받고 있다. 특히 고 직접화 전자 소자의 발열 문제를 해결하기 위해, 소형화와 정밀 온도 제어가 가능한 박막형 열전 소자에 연구가 주목 받고 있다. 박막형 열전소자 중 산화물 반도체계에 대한 연구가 활발히 진행되고 있으며, 이러한 산화물 반도체계 중 In2O3는 BiTe, PbTe 등의 기존의 재료에 비해 독성이 낮을 뿐만 아니라 내 산화성 및 고온에서 열적 안정성이 우수하여 고온에서 적용 불가능한 금속계 열전 재료의 한계를 극복 할 수 있다는 장점을 가진다. 우수한 성능 가장 낮은 캐리어 밀도를 가지기 때문에 의 열전 재료는 높은 전기 전도도 및 제백 계수 그리고 낮은 열전도도 특성을 가져야만 한다. IZO:Sn(Zn 10 wt.%, Sn 800 ppm) 박막의 경우, 높은 전기 전도성을 가지면서 비정질 구조를 가진다. 이와 같이 비정질 구조를 가지는 박막 열전 재료는 격자에 의한 열 전도도가 낮기 때문에 결정질 구조에 비해 전체 열 전도도 값이 낮을 것으로 기대된다. 따라서 높은 전기 전도도를 가지면서 동시에 낮은 열 전도도를 가지게 되어 우수한 열전 특성을 가질 것이라 예상된다. 이러한 특성을 바탕으로 본 연구에서는 비정질 구조를 갖는 Zn와 미량의 Sn을 동시에 첨가한 In2O3박막의 전기적 특성및 열전 특성을 관찰하고자 한다. 본 연구에서는 magnetron sputtering법으로 IZO:Sn(Zn 10 wt.%, Sn 800 ppm) 타깃을 이용하여 기판 가열없이 DC Power 70 W, 작업 압력 0.7 Pa으로 SiO2 기판 위에 $400{\pm}20nm$ 두께의 박막을 증착하였다. 이러한 공정으로 만들어진 박막은 대기 중 후 열처리를 각각의 200, 300, 400, 500, $600^{\circ}C$ 온도에서 진행하였다. 박막의 미세 구조는 XRD를 통해 관찰하였다. 그리고 박막의 전기적 특성은 Hall effect measurement을 통해 측정하였고, 열전 특성은 Seebeck 상수의 측정을 통하여 평가하였다. XRD 확인 결과 RT에서 증착한 박막과 후 열처리 200, 300, 400, $500^{\circ}C$ 결과 비정질 구조를 보였고, 후열처리 $600^{\circ}C$에서는 결정의 회절 피크를 보였다. 전기적 특성의 경우, 후 열처리 온도가 증가함에 따라 전기 전도도는 감소한다. 이는 공기중의 산소가 박막에 침투하여 oxygen vacancy를 막아 캐리어 밀도가 감소한것에 기인 된 것으로 판단된다. 열전 특성의 경우 제백상수는 후 열처리 $600^{\circ}C$에서 가장 높은 제백상수를 나타낸다. 제백 상수는 수식에 따라 캐리어 밀도의 -2/3승에 비례하게 된다. 수식에 따라 후 열처리 $600^{\circ}C$에서 가장 낮은 캐리어 밀도를 가지기 때문에 가장 높은 제백 상수를 가지게 된다. 열전 성능 척도인 Power factor는 제백 상수의 제곱과 전기전도도의 곱으로 나타내는데, 후 열처리 $200^{\circ}C$에서 가장 높은 Power factor를 보인다. 이는 캐리어 밀도 감소에 따라 전기 전도도는 감소하였지만 이로 인해 제백상수는 증가하였고, 또한 캐리어 밀도 감소에 따라 이온화 불순물 산란의 감소에 의해 이동도의 증가에 의한 것으로 판단된다. 박막의 경우 기판의 영향으로 인해 열 전도도 측정이 어려워 열전 성능 지수(ZT)를 계산을 할 수 없지만, 마그네트론 스퍼터링법으로 증착한 IZO:Sn 박막은 비정질 구조를 가지므로 격자진동에 의한 열 전도도가 낮아 전체 열 전도도가 결정질에 비해 낮을 것이며 이는 높은 열전 성능 지수를 가질 것으로 예상된다.