• Journal of the Korean Geotechnical Society
• /
• v.30 no.3
• /
• pp.5-16
• /
• 2014

Soil-nailing has two main resistance factors: skin friction between ground and grouting; and tension load of reinforced material. These two factors will affect the load-displacement curve when performing soil-nailing pullout tests. The purpose of this paper is to figure out the shear behavior between ground and soil-nailing focusing on the net load-displacement behavior during soil-nailing pullout tests. Firstly, the net load-displacement curve between ground and grouting is estimated theoretically. Then, in-situ pullout load tests are performed on various ground conditions to obtain the load-displacement curve occuring between ground and grouting. Since the measured shear displacement includes elongation of the reinforced material (steel nails), the net load-displacement curve can be obtained by subtracting the elongation magnitude of steels from the measured displacement. It was found that the measured net load-displacement curve matches reasonably well with the theoretically estimated curve.

• The Journal of Engineering Geology
• /
• v.23 no.1
• /
• pp.47-55
• /
• 2013

To analyze lateral displacement of excavation walls exposed during the construction of Subway Line 1 in the Daegu region, inclinometer measurement data for sites D4, D5, and Y6 are investigated from the perspective of engineering geology. The study area, in the Banyawol Formation, Hayang Group, Gyeongsang Supergroup, is in the lower part of bedrock of andesitic volcanics, calcareous shale, sandstone, hornfels, and felsite dykes that are unconformably overlain by soil. The rock mass around the D4 site is classified as RMR-V grade and the maximum lateral displacement of 101.39 mm, toward N34W, was measured at a bedding-parallel fault, at a depth of 12 m. The rock mass around the D5 site is classified as RMR-IV grade and the maximum lateral displacement of 55.17 mm, toward the south, was measured at a lithologic contact between shale and felsite, at a depth of 14 m. The rock mass around the Y6 site is classified as RMR-III grade and the maximum lateral displacement of 12.65 mm, toward S52W, was measured at an unconformity between the soil and underlying bedrocks, at a depth of 7 m. The directions of lateral displacement in the excavation walls are vector sums of the directions perpendicular to the excavation wall and horizontally parallel to the excavation wall. Lateral displacement graphs according to depth in the soil profile show curvilinear trajectories, whereas those in bedrock show straight and rapid-displacement trajectories.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.587-597
• /
• 2007

Steel restrainer cables for multiple frame bridges in California in the United States have been shown to be effective in preventing unseating at internal hinges during the past several earthquakes. Consequently, the steel-cable-restrainer is being tested for applications on multiple-span-simply-supported (MSSS) bridges in the mid-American region. In addition, shape memory alloy (SMA) bars in tension are being studied for the same application, multiple frame bridges, the developed seismic forces are transferred to piers through the restrainers. However, in MSSS bridges, the seismic forces are transferred to abutments by the restrainers. Therefore, the abutment' behavior should also be investigated. In this study, we assessed the seismic performance of the three types of restrainers, such as steel restrainer cables, SMA in tension, and SMA in bending for an MSSS bridge from moderate to strong ground motion, bending test of an SMA bar was conducted and its analytical model was determined for this study. Nonlinear time history analyses were conducted to assess the seismic responses of the as-built and the retrofitted bridges. All three types of restrainers reduced the hinge opening and the SMA in tension was the most effective of the three devices in preventing the unseating, all restrainers produced damage on the abutment from the pulling action of the MSSS bridge due to strong ground motions, was found that the retrofit of the abutment in the pulling action is required in the installation of restrainers in MSSS bridges.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.61-66
• /
• 1999

반복 응력 상태 아래서 알루미나 세라믹의 피로 표면손상 누적현상이 분석되었다. 연속 미끄럼 접촉 시에 발생하는 응력 상태를 재현하기 위해서 동시에 작용하는 수직-수평 반복 압축하중 기법이 사용되었다. 알루미나 구와 평판의 접촉면에서 알루미나 미세 결정의 피로 파손에 의한 마모 입자 형성 기구가 관찰되었고, 반복하중의 횟수와 수직-수평 하중비가 커질수록 마모량은 증가하였다. 반복 접촉하중에 의한 표면손상 누적이 접촉 수직 변위 측정으로 정량화 되었다. 두 접촉 구조물의 강성 (하중-변위 선도의 기울기) 변화가 두 재질의 탄성계수의 변화로 표현되었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.04b
• /
• pp.449-453
• /
• 1994

공작기계의 가공정밀도는 공구와 공작물간의 상대변위 크기로서 평가되는데, 이 상대변위는 가공중에 발생 하는 절삭력이 공구-척-주축-기계구조물-안내면-가공테이블-공작물로 이어지는 하중전달 폐곡선을 흐르면서 경로상의 정적, 동적 취약부의 주된 영향을 받아 생기거나 각 요소부품의 변형이 누적되어 생겨난다. 본 연구에서는 주축의 취약부를 규명하기 위하여 정적으로는 정적 처짐곡선을 이용하고, 동적으로는 진동모우드의 굽힘곡선을 이용하여 주축선단의 처짐에 가장 영향을 많이주는 부위를 파악하였다. 취약부의 개선방법으로는 주축지름을 변화시켜 주축선단 근처에서 굽힘이 집중되지 않도록 유도하였다. 그리고 구조개선의 효과를 확인 하기 위해서 기존 주축시스템과 개선 주축시스템의 정적, 동적 특성변화를 비교하였다.

• Tribology and Lubricants
• /
• v.7 no.2
• /
• pp.22-27
• /
• 1991

접촉운동에 의해 재료 접촉부위의 기계적 상태의 변화가 야기될 때 에너지가 방출되며 그 중의 일부는 AE(음향방출)의 형태로 방출된다. AE가 재료의 표면과 작용해서 일어나는 표면변위(surface displacements)는 기술적으로 표면에 설치한 변위계(displacement sensor)에 의해 쉽게 측정될 수 있으며 이 측정값은 AE가 발생된 물리적인 원인을 설명해주는 여러가지 정보를 제공한다. AE측정의 용이함에 재료의 기계적 변형, 파단과구조 및 조성 등의 변화와 AE와의 밀접한 관계로 인해, 재료의 마찰 접촉시의 거동을 이해하기 위해 AE 모니터링이 점차 활발히 적용되고 있다.

• Journal of the Korean Society for Railway
• /
• v.6 no.4
• /
• pp.30-36
• /
• 2003

궤도(track)는 열차가 안전하고 승차감(乘車感)이 좋게 운행되도록 충분한 강도를 가지고 더욱이 양호한 상태로 정비되어 있어야 한다. 일반적으로, 토목구조물(structure)은 하중을 받으면 변위(變位)ㆍ변형하고, 하중이 없게 되면 원래대로 되돌아간다. 즉, 각 부재는 탄성 한계 내로 응력(應力)이 들어가도록 설계된다. 그러나, 궤도는 열차의 하중과 진동을 궤도 자신의 변위 축적으로 흡수하고 있다. 결국, 처음부터 틀림이 진행되어 가는 것을 전제로 한 유일한 구조물이다. 일반적으로는 스프링 하 중량과 축중(軸重)이 큰 차량이 빠르고 대량으로 주행하게 되면 궤도 틀림이 발생하여 진행한다. 궤도 틀림 파형의 성장은 궤도 틀림이라고 하는 공간적인 파형의 시간적인 추이라고 하는 2차원적인 취급이 필요하다. (중략)

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.218-221
• /
• 2011

본 연구에서는 추계학적 해석을 통하여 구한 교량의 동적 변위와 동일한 변위를 발생시키는 등가 정적 버페팅 하중을 구하는 방법을 제시하고, 단순 양단 캔틸레버에 적용하여 타당성을 검증하였다. 모드 형상이 복잡한 사장교의 경우에 2개 이상의 모드를 포함해야 정확도를 높일 수 있는 것으로 나타났다.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.52-58
• /
• 2014

Plastic deformation of roadbed influences the stability and maintenance of concrete slab track. Long-term plastic deformation in a railway roadbed is generated primarily due to accumulated inelastic strains caused by repeated passing of trains. Prediction of cumulative plastic deformation is important in cost-effective maintenance of railway tracks as well as for the safe operation of trains. In this study, the vertical displacements in railway roadbeds with different thicknesses of reinforced roadbed were computed. Parameters of the power model for cumulative plastic strain were calibrated by using the data from triaxial tests and full-scale loading tests. Results of three-dimensional finite element analyses of standard roadbed sections provide us with design guidelines for the selection of the thickness of reinforced roadbed.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.4
• /
• pp.3-15
• /
• 2001

Generally, it has been noted that underground structures have a consistent record of suffering much less damage than surface facilities during earthquakes; but it is still necessary to illustrate the dynamic response of tunnel structures subject to earthquake loadings and to provide the appropriate method for the seismic analysis of underground tunnel structures since many types of underground structures have been and will be constructed in countries situated within seismic zones. In this study, first, seismic analyses for underground tunnel structures are performed by using quasistatic analysis method and dynamic analysis method. Second, seismic analyses in tunnel portals are performed by using above methods. The results of seismic analyses for the tunnel structure show that the tunnel structure conforms to ground deformation and that seismic design by using the quasi-static analysis method is more conservative than that by using the dynamic analysis. The results of the dynamic FEM analysis for the tunnel structure show that the simplified 2-D FEM analysis using a sine wave rather than the 3-D FEM analysis can be adopted for seismic analysis. Finally, the results of the dynamic FEM analysis in tunnel portals show that the force acting on the lining is largest near to the tunnel portal when an earthquake wave propagates parallel to tunnel axis.