• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.20-29
• /
• 2011

There are a lot of electrical and electronic components and pneumatic parts sensitive to vibration and shock in the VEB assembly which KARI directly transports among the KSLV-I upper stage transportation items. So, the special attention in the transportation is required. The transportation container with the apparatus for controlling environment was made in order to meet the requirements. The transportation tests using the engineering model were performed 4 times to verify the performance of the transportation container and to conform the transportation conditions(transportation velocity, route, etc.). In this document, the previous transportation history of the VEB assembly, the overview and the result of the KSLV-I FM unit 2 VEB assembly transportation are described.

• Aerospace Industry
• /
• s.90
• /
• pp.54-56
• /
• 2006

한국항공우주산업(주) 벨사에 헬기 동체 1억5000만 달러 수출/대한항공,다목적실용위성 설계/산자부,항공우주부품기술개발에 115억 원 지원/KAI, XKT-1 총조 립 착수/대한항공,주한 미군RC-12 기체 창정비 1호기 인도/다목적실용위성2호,7월발사/F-15K,SLAM-ER 미사일 발사 성공/P-3C 2차 사업 성능개량 착수/ 대한항공 안전평가 세계 12위/한국 우주인 본격 추진

• Journal of Astronomy and Space Sciences
• /
• v.18 no.2
• /
• pp.137-144
• /
• 2001

This paper presents the REA thrusters performance estimation results for the KOREASAT F1&F2 launched in 1995 The satellite tracking data obtained from the ground system from end of 1999 to beginning of the 2000 are used to estimate the thruster performance. The estimation algorithm is derived from the least square estimation theory and designed to estimate the velocity change induced by the on-boarded thruster firing as well as the orbit parameter. The estimation results show that the Koreasat F1 thruster are in bad thruster condition of 64% performance for REA when it fires in on-pulse mode. Here, the performance is defined by the ratio of the resulted velocity change to that of planned. But, in the case o( the Koreasat F2, it is found that the performance approximately reaches up to 100%, even after the 5 years of the mission.

• Proceedings of the Korean Information Science Society Conference
• /
• 2003.10b
• /
• pp.346-348
• /
• 2003

본 논문에서는 2004년 12월 발사 예정인 다목적실용위성 2호의 탑재소프트웨어의 구성과 전반적인 개발 과정 및 개발 환경에 관련된 내용을 서술한다. 다목적실용위성 2호 탑재소프트웨어 개발은 다목적실용 위성 1호 탑재소프트웨어를 근간으로 2호기 요구사양에 따라 요구사양 분석, 설계. 코딩 및 단위 테스트, 통합 테스트와 검증 시험 등을 거쳐 진행되었으며 일련의 모든 개발과정은 국내 연구진에 의해 수행되었다.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.08a
• /
• pp.36-37
• /
• 2000

정밀 지상관측 위성인 다목적실용위성 1호기에는 해상도 6.6 m인 전자광학카메라(EOC)가 탑재되어 현재 우수한 영상을 보내오고 있으며 2003년 발사예정인 2호기를 위하여 해상도 1 m의 Multispectral Camera(MSC)가 개발중이다. 미 TRW 사가 제작한 EOC 개발에 항우연의 연구진은 그 설계 및 시험의 각 단계별 검토와, 탑재, 위성전체 시험과 보정을 포함한 궤도운용 등의 수행과 함께, 개발기간 동안 현지에서 수행된 별도의 현장교육을 통하여 동급의 위성카메라를 실제 개발할 수 있는 설계기술을 이전받았다. 수차례 대구경 비구면 광학계 제작 경험을 더한 항우연은 MSC 공동개발선인 이스라엘 ELOP 사와 현재 그 설계를 진행하고 있다. (중략)

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.80-88
• /
• 2003

The present analysis quantifies the particulate contamination of KOMPSAT-2 satellite until in orbit life. Assumptions are defined about integration and test conditions and durations, then a budget is drawn. As KOMPSAT-2 activities are carried out in good cleanliness conditions, the particulate contamination budgets for satellite and instrument surfaces at BOL is fair. To summarise, in the baseline launch conditions (class 10,000) the contribution of satellite AIT and launch activities adds 500 PPM to MSC and STA apertures (telescope mirrors ; front lens ; baffle), 20,000 PPM to MSC and STA outer surfaces, 14 000 PPM to plate-form horizontal surfaces, 1400 PPM to plate-form vertical surfaces, 1000 PPM to plate-form radiators and less than 300 PPM to solar arra.

• Nuclear Engineering and Technology
• /
• v.18 no.1
• /
• pp.27-37
• /
• 1986

The neutron fluxes and dose rates due to radiation streaming from reactor cavities were evaluated at the KNU-1 reactor pressure vessel (RPY) head flange elevation. To find a suitable cross section data set for the evaluation, a benchmark test was performed for three data sets; DLC-23/CASK, DLC-31/FEWG, and DLC-47/BUGLE. The leakage fluxes from the KNU-1 RPV outer surface were calculated with two different methods: 1-D calculation with ANISN, and 2-D calculation with DOT3.5. The Monte Carlo procedures as embodied in the MORSE-CG code combined with the albedo option were applied to predict the radiation distributions in the cavity region. Finally, the activation analysis of the stud bolts was performed to identify the major activation products.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.228-232
• /
• 2002

본 연구에서는 다목적 실용위성 2호기에 적용된 금속 구조물 중 알루미늄 샌드위치 패널 구조인 탑재체 플랫폼과 튜브 스트럿(tube strut) 구조에 복합재료 응용기술을 적용하였다. 복합재료 구조로의 대체 설계에서도 관성하중 및 음향진동등과 같은 극심한 발사환경과 더불어 운용하게 될 우주 열환경을 고려하였다. 연구의 목적은 금속소재보다 비강도, 비강성이 우수한 복합재료를 위성 구조물에 사용함으로써 무게를 경량화함에 있다.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.57-65
• /
• 2002

The Electrical Power System (EPS) shall supply required power to maintain spacecraft and payload during the mission. The EPS sizing are based on space environment, satellite mission and lifetime, and allocated budgets. The type of the primary and secondary power is determined according to satellite design-level and allocated subsystem budgets. The design of EPS has closely related to system and others' subsystems design. To supply the sufficient power to the satellite, the implementation of the larger power source and energy storage is impossible actually. And there will be some problems of the attitude control of the satellite, the handling power capability of the electronic boxes, and launch vehicle selection caused by EPS oversizing. Also, the thermal control is not easy in the space by extra power. And the maintenance of the satellite within the specific orbit from orbit-drag is a big design burden of the thruster. So the various technologies have been developed to optimize the EPS sizing and to operate the power system efficiently.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.27-30
• /
• 2005

Hanwha Corporation succeeded in domestic development of thruster heat shield for KOMPSAT-2 propulsion subsystem partly. Thruster heat shield, one of the main components of DTM, is designed to prevent the critical radiative heat exchange between thruster and satellite during firing. To overcome the manufacturing difficulties, an electro-forming process is preferred to classical welding process. In this case, an inner diameter of a new shield will be decreased a little due to the change of manufacturing process. The interference problem between thruster nozzle and heat shield was investigated through structural analysis by KARI. Hanwha manufactured heat shield based on the analysis results. In this paper, full development process is described for design, analysis, manufacturing of heat shield.