• Journal of Korean Society of Forest Science
• /
• v.108 no.3
• /
• pp.341-348
• /
• 2019

In order to reduce the safety risk of forestry operations, this research was conducted to examine the suitability of chainsaw protective pants after repeated laundering, testing four different products that are currently used in hand-held chainsaw operations. Laundering was repeated 10, 20, 30, 40, and 50 times. After washing, we measured the shrinkage ratio of 17 measurement positions mostly affecting the safety of forest operations and suggested the expected safety life cycle of chainsaw protective clothes. The results showed that most of the products have only one measurement position where the standard shrinkage ratio (<6%) was exceeded after 20 washings, and that the lateral direction of measurement positions shrank more than the vertical one. The numbers of repeated launderings and measurement positions were found to be significant factors influencing the shrinkage ratio (p<0.05). In the shrinkage rates for 17 measurement positions, there were significant correlations between five of the measurement positions (a, b, g, j, and n) and the number of repeated launderings (p<0.05). Therefore, the results suggest that about 10 months would be suitable for an adequate safety lifetime for chainsaw protective pants. The relationship between the number of repeated launderings and the measurement positions will be further analyzed in detail to examine the durability of chainsaw protective pants.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.11
• /
• pp.15-23
• /
• 2015

An experimental study has been conducted to evaluate the effects of average and cyclic shear stresses on the undrained failure behaviors of dense marine silty sand by using the Cyclic Direct Simple Shear apparatus. The results show that when the average shear stress ratio is zero, symmetric cyclic shear deformation is the major component of deformation, and permanent shear deformation is relatively small. On the other hand, when the average shear stress ratio is larger than zero, asymmetric permanent shear deformation is the major component, and cyclic shear deformation does not change much as the number of cyclic loads increases. The average shear stress ratio has less effects on the number of cyclic loads needed to fail, as compared with the cyclic shear stress ratio. The proposed stress-dependent failure contour can effectively be used to assess the cyclic shear strength of soil beneath the foundation for the design of offshore structures.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.1
• /
• pp.79-91
• /
• 2017

An experimental study has been conducted by using the Cyclic Direct Simple Shear apparatus to evaluate the influence of average and cyclic shear stresses on the undrained shear failure behavior of marine silty sand considering various relative densities. The obtained results show that despite using different relative densities, similar trends were gained in the cyclic shear deformation. Moreover, the cyclic shear deformation is affected mainly by the average and cyclic shear stresses. The number of cyclic loads for failure is significantly affected by the cyclic shear stress ratio and relative density, and is less affected by the average shear stress ratio. The proposed three-dimensional stress-dependent failure contour can be used effectively to assess the soil shear strength considering various relative densities in the design of foundation used for offshore structures.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.1
• /
• pp.43-48
• /
• 2009

This study was performed to investigate the characteristics of nutrient removal by Sequencing Batch Reactor (SBR) system, which could achieve high removal efficiencies of nitrogen and phosphorus and make it possible convenient management and operation. In this study, dissolved oxygen (DO), chemical oxygen demand (COD), nitrogen, and phosphorus in SBR system were examined by variation of anoxic-oxic phase repetition in order to optimize an operational method. The 1~4 times of anoxic-oxic phases (Run 1~4) were repeated during 1 cycle operation period. As the repetition frequency increased, it was more difficult to maintain DO condition enough for denitrification. The SBR system showed high COD removal efficiency more than 91% regardless of operational condition. About 68% of nitrogen removal rate was obtained in conditions of 2 or 3 times repetition of anoxic phases, in which NOx-N among discharged total nitrogen account for more than 99%. Approximately 40% of phosphorus was eliminated in the conditions of 1~3 times of anoxic phase repetition.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.4 no.2
• /
• pp.24-32
• /
• 1998

This study examined the effects of recycling on chemical pulp fibers from multiple recycles. Firstly, water-pretreated alkaline photocopy paper was disintegrated by TAPPI standard disintegrator at room temperature. After dewatering, this pulp was dried in oven at $80^{\circ}C$ for 24hrs. A sequence of wetting, disintegrating and drying was one recycling cycle and this cyclic treatment was repeated from zero to five times. The recycled handsheet dropped to 90% of the original brightness after five cycles, and lost the most brightness in the first two cycles. However, it had a gain of 10% in opacity after five cycles. And, in this study, the method for determining residual ink(toner) content in recycled handsheets were estabilished by means of SEM-EDX and atomic absorptive photometer. The change of residual ink percentage on recycled paper showed the effect of recycling numbers on deinkability of waste paper. A slight decrease in deinkability was noted for the recycled handsheets, which may be due to the change of fiber surface free energy connected with fiber swelling.

• Journal of Advanced Navigation Technology
• /
• v.12 no.6
• /
• pp.619-626
• /
• 2008

In this paper, we proposed a RSS based cooperative localization algorithm using VRN for wireless sensor networks, which can estimate the BN position. The proposed localization system monitoring all nodes estimates a position of BN, and calculates an intersection area with cooperative localization. From the results, we confirm that BN intersection area is reduced as the number of RN is increased. In addition, the fewer RN exists, the more iteration needs at least 4 times. Moreover, the propose algorithm using 4 RNs is improved 71.6% estimation performance than conventional method. Therefore, the cooperative localization algorithm with VRN provides higher localization accuracy than RSS based conventional method.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.4
• /
• pp.40-46
• /
• 2006

The performance of iterative multiuser detector and turbo decoder is presented to provide high quality multimedia services in WCDMA (wideband code division multiple access) system in this paper. Especially the relationship between the local iteration of turbo decoder and the global iteration of multiuser detector including the turbo decoder is analyzed. As a result, three local iterations and three global iterations are considered to be sufficient to provide satisfactory error performance with resonable complexity. The interference cancellation capability of global iteration is improved when the number of users is increased.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.143-151
• /
• 1998

최근들어 반복하중에 의한 철근콘크리트 구조물의 손상이 자주 발견되고 있으며 교량 등의 구조물 등은 때때로 과적차량에 의한 초과하중을 받아 이러한 피로손상이 심화되고 있다. 본 연구에서는 이러한 반복 하중을 받는 철근 콘크리트보의 누적피로손상에 대한 실험적 연구룰 수행하여 피로하중에 의한 철근콘크리트보의 손상과정을 규명하였다. 실험 변수를 전단철근의 양과 반복되는 하중의 크기 및 반복횟수로 하여 실험부재를 제작하였으며, 하중제어에 의한 휨시험법에 의해 3Hz의 반복하중을 시편에 재하하였다. 사인장 균열하중과 사인장 균열 후 반복하중에서의 보의 손상누적거동 즉 처짐. 전단철근의 변형도, 에너지 손실 등의 변화를 실험적으로 평가하였으며, 이를 통하여 반복하중에 의한 누적손상에 의해 철근 콘크리트보의처짐 및 전단변형도가 초기하중상태에서는 급격히 증가하다가 이후 점진적으로 증가하는 것을 규명하였다. 본 연구의 결과는 사용하중상태에서 점진적으로 발생할 수 있는 피로손상의 누적과정을 기술하여 주고 있다.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.11
• /
• pp.25-32
• /
• 2007

In this paper, we propose the Group Separation Algorithm for RFID Tag Anti-Collision. We study the RFID Tag anti-collision technique of ALOHA and the anti-collision algorithm of binary search. The existing technique is several problems; the transmitted data rate included of data, the recognition time and energy efficiency. For distinction of all tags, the Group Separation algorithm identify each Tag_ID bit#s sum of bit #1#. In other words, Group Separation algorithm had standard of selection by collision table, the algorithm can reduce unnecessary number of search even than the exisiting algorithm. The Group Separation algorithm had performance test that criterions were reader#s number of repetition and number of transmitted bits for understanding tag. We showed the good performance of Group Separation algorithm better than exisiting algorithm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.9
• /
• pp.2029-2035
• /
• 2013

In this paper, we presented non-uniform quantization method for LDPC decoder specified in DVB-S2 standard. There are some problems in order to implement LDPC decoder in aspect to algorithm and implementation. In algorithm aspect, because of large number of iterations, LDPC decoding in general give rise to a large number of computation operations, mass power consumption, and decoding delay. Therefore, this paper studies Horizontal Shuffle Scheduling (HSS) algorithm which reduced iteration number without performance loss. In aspect of implementation, there are some solutions to improve the decoding speed, however this paper focused on non-uniform quantization which reduce the quantization bits of LDPC decoder. In simulation results, Decoding throughput of HSS LDPC decoder based on non-uniform quantization is 816Mbps and it improved 12% compared to conventional one.