• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.489-495
• /
• 2016

This study focuses on a detailed ball-bearing model for spur gears. The nonlinear ball-bearing stiffness with radial clearance is derived and calculated. The bearing stiffness is used to the 3-degree-of-freedom (DOF) spur gear system model. The mode characteristics of the gear system model are analyzed and verified by performing finite-element analysis (FEA). From the results, the bearing stiffness on the radial clearance was more sensitive under low-load conditions compared to high-load conditions. The bearing stiffness significantly affected the gear dynamics in the low-frequency region, while the mesh stiffness affected the high natural frequency.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.351-358
• /
• 1994

A probabilistic model and analysis methods to determine the means and variances of the velocity and acceleration in stochastically-defined planar pin jointed kinematic chains are presented. The presented model considers the effect of tolerances on link length and radial clearance and uncertainty of pin location as a net effect on the link's effective length. The determination of the mean values and variances of the output variables requires the calculation of sensitivities of secondary variables with respect to the random variables. It is shown that this computation is straightforward and can be accomplished by a conventional kinematic analysis package with minor modification. Thus, the concepts of tolerance and clearance have been captured by the model and analysis. The only input data are the nominal linkage model and statistical information. The "effective link length" model is shown to be applicable to both analytical solution and Monte Carlo simulation. The results from both methods are compared. This paper Ksolves the higher-order kinematic problems for the probabilistic design analysis of stochastically-defined mechanisms.echanisms.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.12
• /
• pp.994-1003
• /
• 2018

The clamping characteristics of segmented nuts in pyrotechnic separation nut are investigated using finite element analysis. When the segmented nuts are used to clamp objects, a constraint cylinder is necessary to prevent the segmented nuts from spreading out to the radial direction. During the manufacturing process, a clearance is usually introduced between the outer diameter of the segmented nuts and the inner diameter of the constraint cylinder. Therefore to find out the effect of the clearance, proper finite element modeling method is suggested to describe the clamping procedure appropriately. In addition, finite element analysis with the clearance of 0.00, 0.03, 0.06, and 0.10 mm are performed. From the analysis results, the clamping characteristics of segmented nuts are investigated according to the clearance, and several factors which should be considered to design a reliable pyrotechnic separation nut are figured out.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.10
• /
• pp.843-851
• /
• 2003

The present paper studies the leakage flow model used in the performance prediction of a scroll compressor. Two leakage flow models, isentropic and Fanno flow model, are studied in detail. Their predictions are also compared with CFD solutions to check the validity as a leakage flow model. Comparison with CFD solutions shows that the isentropic flow model predicts excessive leakage flow rate, while the Fanno flow model shows acceptable agreement with CFD solutions. The excessive leakage flow rate by isentropic flow model results in under-prediction of the overall performance of a scroll compressor.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.225-230
• /
• 1998

DUPIC 핵연료 소결체의 하나로 조사시험과 관련하여 이중 피복관으로 구성된 소결체 설계를 수행하였으며 각각의 설계변수가 핵연료의 온도에 미치는 영향하였다. 하나로에서 조사할 DUPIC 핵연료의 설계해석 결과, DUPIC 핵연료의 조사시험시 열전도도, 출력, 반경 틈새 등은 핵연료의 온도에 크게 영향을 미쳤으며, 피복재 두께, gamma열, 열전달 계수 등은 핵연료의 온도에 크게 영향을 미치지 않았다. Transient 온도분석의 경우 약 160초 이상의 시간에서 평형 온도에 도달할 것으로 분석되었다.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.17-30
• /
• 2002

The design method of turbomachinery has been developed highly. But some geometric dimensions have been determined from the empirical view points. In designing the inlet outer diameter of pump impeller and the hub ratio of blower, satisfactory theoretical grounds have not been presented till now. In the paper, these points are discussed and the method of increasing pump and blower efficiencies are also discussed on the basis of experimental and computational results of flow analysis. Further, the effects of tip clearance of rotor on its efficiency and the interference of rotor and stator blade rows are discussed and some ideas to estimate their effects are presented.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1998.11a
• /
• pp.293-299
• /
• 1998

조선업 및 화학공장 등 산업현장의 화재사고 중 용접$\cdot$용단작업시 불티에 의해 주위의 가연성물질을 착화시켜 화재, 폭발 사고를 일으키는 원인이 되고 있다. 이들 불꽃은 수평방향 및 틈새, 배관구멍 또는 마루나 댁의 작은 개구부 등을 통하여 비산되고 상당시간 훈소화재 형태를 유지하다 발화되어 화재의 원인이 되고 있다. 특히, 용단작업시 비산되는 불티는 $1,600^{\circ}C$ 이상의 고온체로서 산소 압력에 따라 다르나 약 11 m(산소압력, 7 kg/$cm^2$)까지 비산되어 이 반경내에 있는 가연물에 착화될 수 있으므로 이에 대한 예방대책이 필요한 작업공정이다. (중략)

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.262-268
• /
• 1999

This paper reviews the rules for optimizing die design and the process variables such as die shoulder radius and punch to die clearance, which are important factors in drawing the sheet metal without failures during deep drawing. To find the optimum conditions for improving deep drawability, a series of the experiments are performed, and the wall thinning and thickening variations are investigated in each process of deep drawing for a complex cylindrical shell. From the results of this proposed experiment, the optimum values of process variables are examined and discussed, and the usefulness of the present suggestion is shown.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.4
• /
• pp.335-341
• /
• 2015

In this study, we analyzed a two-dimensional Stokes flow through a microchannel containing projections with constant spacing attached to each wall. The projections on the top and bottom walls were semi-circular in shape, with in-phase locations. By considering the periodicity and symmetry of the flow, the eigenfunction expansion and least squared error method were applied to determine the stream function and pressure distribution. For some typical radius and spacing values, the streamline patterns and pressure distributions in the flow field are shown, and the shear stress distributions on the boundary walls are plotted. In addition, the average pressure gradients in the microchannel are also calculated and shown with the radius and spacing of the projections. In particular, the results for the case of extremely small gaps between the projections on the top and bottom walls are in good agreement with the lubrication results.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.23-30
• /
• 1999

This paper investigates the radial performance of self-acting spiral-grooved air bearing, used to support small high-speed rotating bodies. Repeatable runout, nonrepeatable runout, stiffness and supporting load are selected as the performance. The clearance between rotor and stator, the stator groove depth, and the rotating speed are chosen as three main parameters affecting the performances. Force application and displacement measurement are done in a noncontact manner, in order not to disturb operation: electromagnetic force is applied to the rotor and gap sensors are used to measure the displacement of the rotor. Experimental results show that repeatable runout decreases as speed, groove depth and clearance decrease. Nonrepeatable runout decreases as clearance decreases, and it has a minimum value at $5.5{\mu}m$ of grove depth and a maximum value at speed of 18.000rpm. Stiffness increases as speed increases and clearance decreases, and has a maximum value around $5.5{\mu}m$ of groove depth. The relationship between force and displacement is linear for small displacement, but becomes nonlinear for large displacement. Supporting load is linearly proportional to the stiffness, and it is a maximum value around $4.75{\mu}m$ of clearance.