• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.6
• /
• pp.457-464
• /
• 2021

To analyze the buffet phenomenon that causes serious vibration loads on a satellite launch vehicle, the pressure fluctuations on a hammerhead launch vehicle at transonic speeds are predicted by coupling CFD analysis and semi-empirical methods. From the RANS simulation, shock oscillation region, separation region, and separation reattachment region are identified, and the boundary layer thickness, the displacement thickness, and flow properties at boundary layer edge are calculated. The pressure fluctuations and power spectra on the hammerhead fairing are predicted by coupling RANS results and semi-empirical methods considering spatial distribution, and compared with the experimental data.

• Composites Research
• /
• v.34 no.3
• /
• pp.143-147
• /
• 2021

Full width half maximum (FWHM) analysis of superimposed terahertz (THz) signals in the glass fiber reinforced polymer (GFRP) was studied to detect fine delamination inside GFRP. The THz signals were measured for each fine delamination size inside the GFRP using the reflection mode of the terahertz time domain spectroscopy (THz-TDS) system. Then, the FWHM of the superimposed THz signal reflected at the fine delamination was extracted. Thereafter, the complex refractive index of the GFRP was measured using transmission mode of the THzTDS system. Based on this, the FWHM of the superimposed THz signal at the fine delamination were calculated and compared with respect to the fine delamination size. From the theoretically calculated superimposed signals, the relationship between the fine delamination size and the FWHM in the superimposed THz signal was derived. Consequently, the fine delamination size could be predicted through the analysis of the FWHM extracted from the THz signal at the fine delamination.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.69-75
• /
• 2009

This paper studies the aerodynamic performance that the vent mixer-new conceptual supersonic mixer-showed with its geometric characteristics. The hole is 2 mm with 2 mm's distance from the wall in case 1 and with no distance in case 2. In case 3 die hole is 1 mm. Case 1 and case 2 showed the same total pressure recovery ratio, of which the case 3 was lower than that. While cases 1-3 had the same reattachment length, the shear layer was thicker in cases 1 and 2 than in case 3. Within the recirculation zone, cases 1 and 2 had lower pressure loss and higher velocity gradient difference than case 3-they enhance mixing between air and fuel. Separation bubble which is developed by the inflow into the recirculation zone has a significant effect on the total pressure recovery ratio in the combustor. Also separation bubble influences pressure distributions and recirculation flows in the recirculation zone. Therefore, inflow rate of air into the recirculation zone mainly affects the performance of vent mixer.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.415-420
• /
• 2013

천음속 영역에서 비행하는 에어포일 주위의 유동은 아음속 영역과는 달리 충격파(Shockwave)를 동반하고 이에 따라 복잡한 유동 현상이 발생한다. 본 연구는 천음속 영역에서 설계된 에어포일 주위의 유동에서 충격파 발생에 따른 유동변화의 특징들을 관찰하였다. 특히, 충격파에 의해서 발생하는 진동(Buffeting)과 경계층 유동 박리(Shock-induced boundary layer separation)현상에 대한 관찰과 일반적인 에어포일과 초임계 에어포일(Supercritical airfoil)간의 유동 특성의 차이점을 분석하였다. 본 연구를 위해서 EDISON CFD코드가 사용되었다.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.131-136
• /
• 1999

박리를 수반하는 진동하는 이차원 익형 주위의 비정상 유동장에 대해 SST 난류 모델을 이용하여 해석을 수행하였다. SST 모델은 정상 유동장 해석에서 기존의 난류 모델에 비해 우수한 성능을 보인다고 알려져 있으나 큰 박리영역에서 공력 계수의 진동 현상을 보이는 등 비정상 유동장 해석에 문제점을 보이고 있다. 본 논문에서는 이러한 공력 계수의 진동 현상이 SST 모델을 이차원으로 확장하는 과정에서 발생한 것임을 밝히고 이에 대한 보완을 통하여 수정된 SST 모델을 제시하고자 한다. SST 모델의 기본이 되었던 BSL 모델 및 SST 모델, 수정된 SST 모델을 사용하여 정상 유동장과 비정상 유동장 해석을 수행하여 각 모델의 난류 유동장 해석 특성을 비교하고 이를 통하여 수정된 SST 모델이 박리를 수반하는 비정상 유동장 해석에서 원래의 SST 모델에 비해 향상된 결과를 나타남을 알 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.9
• /
• pp.1-8
• /
• 2005

This paper explored the effects of separation control through the use of pulsating jet blowing on a two dimensional elliptical airfoil. To develop an active control technique of flow separation, a flow control actuator utilizing continuous/pulsed jet of pressurized air was designed and installed in a wind tunnel testing model of elliptic wing. PIV measurement and flow visualization of the wing near field were conducted to access the feasibility and effectiveness of the pulsed jet blowing on controlling the stall of the elliptical wing in subsonic flow. PIV experimental results show that separation control can provide significant reduction in turbulent flow wake and separation bubbles by jet blowing. The pulsating jet blowing is more effective on the separation control than continuous one. Increased jet frequency suppressed the turbulent separated flow wake effectively at even higher AOAs.

• 보존과학연구
• /
• s.33
• /
• pp.57-67
• /
• 2012

The Uiseong Tapriri Five-Storied stone pagoda has occurred exfoliation, granular disintegration and discoloration by physical and chemical weathering factors with the major deterioration occurring due to efflorescence by salt. According to the results of SEM-EDS and X-ray diffraction analysis, salts consists of gypsum, taranakite. Artificial salt weathering tests were carried out using the same type of rocks as those in the stone pagoda. The test results showed that efflorescence occurred on the surface of the rock, and that exfoliation and granular disintegration occurred inside the rock due to salt crystallization.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.87-94
• /
• 2006

An experimental research program providing knowledge to measure two-dimensional skin friction variation over a certain region of model surface is presented. In the oil-fringe imaging skin friction(FISF) technique, local slope of a thin oil applied on a test surface is measured from the interference fringe patterns on the oil surface, and its information is then related to the applied shear over the oil by the thin-oil lubrication theory. The FISF technique has been applied for a separation flowfield ahead of a circular cylinder vertically mounted on a flat plate, and it has been found that the FISF skin friction results show good comparison with the other numerical/experimental data obtained for similar conditions. implying an applicability of the technique.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.47-55
• /
• 2018

In order to determine whether three-dimensional effects exist in a pintle nozzle of axisymmetric shape, a three-dimensional numerical analysis was performed. The compressibility correction was implemented with the k-${\omega}$ SST turbulence model to predict the complex flow separation transition in acceptable accuracy. Recirculation zones were observed at both the front end and rear faces of the pintle, and the flow through the pintle nozzle conveyed complex shock wave structures. Three-dimensional effects that resulted from the reasonable flow separation location were noted, and a trace of the transient pressure increase was observed, mismatched by a two-dimensional axi-symmetric analysis.

• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.261-264
• /
• 2015

In this paper we show that the photoresist-protective film of a printed circuit board (PCB) can be delaminated from the underlying photoresist layer by a single pulse of a nanosecond laser at 532 nm. After locally peeling the edge of the PCB with a laser beam of 9 mm size, Scotch tape was attached to the irradiated region to peel off the whole protective film. For a certain range of pulse energies the peeling probability was 100%, without leaving any damage. Since the use of a laser in initial delamination is noncontact and nondamaging, it may be more efficiently utilized in the PCB industry than the conventional knurling method based on mechanical pressing.