• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.3
• /
• pp.116-123
• /
• 2023

A high intensity focuses ultrasound (HIFU) is one of the emerging technologies in the biomedical field. The piezoelectric HIFU transducer is a device that utilizes the thermal energy generated by high ultrasound energy. Recently an operating frequency of the HIFU transducer is to expand above a 7 MHz. In this study, the acoustic pressures and temperature distributions in the tissue that generated by the HIFU transducer at 10 MHz were calculated with the finite element method. In addition, the pressure focusing characteristics of the device were analyzed. The geometrical variables are the piezomaterial thickness, lens shape, water height, and film thickness. The results shown that the acoustic pressure increased and saturated gradually when the height/radius (H_L/R_L) ratio of the lens increased. Moreover, the focal area was gradually decreases with H_L/R_L ratio of the lens. In case of the optimized HIFU transducer, the maximum pressure and temperature were analyzed about 19 MPa and 65℃ respectively. And the -3 dB focused distances in the axial and lateral direction are around 2.3 mm and 0.23 mm respectively.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.30 no.1
• /
• pp.1-14
• /
• 2024

As awareness of environmental issues continues to grow, there is an escalating demand for recycling and repurposing byproducts of agricultural and food production processes and their conversion to high-value products. Coffee is the most widely consumed beverage globally; during coffee beverage processing and consumption, byproducts such as coffee silverskin (CS), spent coffee grounds (SCGs), and oil are generated. Despite containing beneficial materials such as cellulose, hemicellulose, lignin, lipids, and bioactive substances, these byproducts are typically discarded in landfills or incinerated. The utilization of CS, SCGs, and oil in the development of packaging materials holds significant potentials toward the realization of a sustainable society. To this end, considerable research efforts have been dedicated to the development of high-value materials derived from coffee byproducts, including functional fillers, polymer composites, and biodegradable polymers. Notably, CS and SCGs have been employed as functional fillers in polymer composites. Additionally, lipids extracted from SCGs have been used as plasticizers for polymers and cultured with microorganisms to produce biodegradable polymers. This review focuses on the research and development of polymer/CS and polymer/SCG composites as well as cellulose extraction and utilization from CS and SCGs and its applications, oil extraction from SCGs, and cultivation with microorganisms using extracted oil for polyhydroxyalkanoates(PHA) production.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.259-266
• /
• 2013

An automated cell tracking system is used to automatically analyze and track the changes in cell behavior in time-lapse cell images acquired using a microscope with a cell culture. Clustering is the partial overlapping of neighboring cells in the process of cell change. Separating clusters into individual cells is very important for cell tracking. In this study, we proposed an algorithm for separating clusters by using ellipse fitting based on a direct least square method. We extracted the contours of clusters, divided them into line segments, and then produced their fitted ellipses using a direct least square method for each line segment. All of the fitted ellipses could be used to separate their corresponding clusters. In experiments, our algorithm separated clusters with average precisions of 91% for two overlapping cells, 84% for three overlapping cells, and about 73% for four overlapping cells.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2493-2499
• /
• 2011

With growth of nano-bio industry, it is of significant importance to develop an automated system to exploit cell behaviors, including migration, mitosis, apoptosis, shape deformation of individual cells and their interactions among cells in the process of cell growth. In this paper, we proposed preprocessing techniques, a classification method which classifies clusters (overlapping multiple cells) from cells and an automated method which counts the number of cells and clusters in order to analyze 2D or 3D deformations of the cells in the real-time images from microscope in the cell culture. We conducted the 3T3 cell images taken from each thirty-minute interval. It showed the average 99.8% accuracy automatically for separating cells and clusters.

• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.693-697
• /
• 2016

In this study, we fabricated the catalysts for enzymatic biofuel cell anode with carbon nanotube (CNT), glucose oxidase (GOx) and various molecular weights branched poly(ethyleneimine)(bPEI) and terephthalaldehyde (TPA) as cross-linker. In case of GOx/bPEI/CNT using only physical entrapments for immobilization, the molecular weights of bPEI didn't affect to electrochemical performances and long term stability. but that of the catalysts cross linked via TPA (TPA[GOx/bPEI/CNT]) improved and the mass transfer of glucose to FAD was interrupted as increasing of the bPEI's molecular weights. Furthermore, it was confirmed that the optimum molecular weight of PEI for TPA [GOx/bPEI/CNT]) structure is 750k that showed marvelous high performance (maximum power density of $0.995mW{\cdot}cm^{-2}$).

• Analytical Science and Technology
• /
• v.29 no.1
• /
• pp.35-42
• /
• 2016

A new nano-composite carbon ink for the development of disposable dopamine (DA) biosensors based on screen-printed carbon electrodes (SPCEs) is introduced. The method developed uses SPCEs coupled with a tyrosinase modified nano-composite carbon ink. The ink was prepared by an “in-house” procedure with reduced graphene oxide (rGO), Pt nanoparticles (PtNP), and carbon materials such as carbon black and graphite. The rGO-PtNP carbon composite ink was used to print the working electrodes of the SPCEs and the reference counter electrodes were printed by using a commercial Ag/AgCl ink. After the construction of nano-composite SPCEs, tyrosinase was immobilized onto the working electrodes by using a biocompatible matrix, chitosan. The composite of nano-materials was characterized by X-ray photoelectron spectroscopy (XPS) and the performance characteristics of the sensors were evaluated by using voltammetric and amperometric techniques. The cyclic voltammetry results indicated that the sensors prepared with the rGO-PtNP-carbon composite ink revealed a significant improvement in electro-catalytic activity to DA compared with the results obtained from bare or only PtNP embedded carbon inks. Optimum experimental parameters such as pH and operating potential were evaluated and calibration curves for dopamine were constructed with the results obtained from a series of amperometric detections at −0.1 V vs. Ag/AgCl. The limit of detection was found to be 14 nM in a linear range of 10 nM to 100 µM of DA, and the sensor’s sensitivity was calculated to be 0.4 µAµM⁻¹cm⁻².

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.410-420
• /
• 2006

The dynamic effects, such as the steering and the screening effects during deposition on an epitaxial growth is studied by kinetic Monte Carlo simulation. In the simulation, we incorporates molecular dynamic simulation to rigorously take the interaction of the deposited atom with the substrate atoms into account, We find three characteristic features of the surface morphology developed by grazing angle deposition: (1) enhanced surface roughness, (2) asymmetric mound, and (3) asymmetric slopes of mound sides, Regarding their dependence on both deposition angle and substrate temperature, a reasonable agreement of the simulated results with the previous experimental ones is found. The characteristic growth features by grazing angle deposition are mainly caused by the inhomogeneous deposition flux due to the steering and screening effects, where the steering effects play the major role rather than the screening effects. Newly observed in the present simulation is that the side of mound in each direction is composed of various facets instead of all being in one selected mound angle even if the slope selection is attained, and that the slope selection does not necessarily mean the facet selection.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.154-154
• /
• 2011

자발형성법(Self-assembled)을 이용한 InAs 양자점(Quantum dots)은 성장법의 고유한 물리적 한계로 길이방향에 대한 수직방향 비율(Aspect ratio, AR)이 상대적으로 작은 값을 갖는다. 기존에 보고된 바에 따르면 GaAs 기판에 형성한 InAs 양자점은 일반적으로 AR이 0.3 정도를 보인다. 이러한 높이가 상대적으로 낮은 InAs 양자점은 수직방향으로 운반자(Carrier)의 파동함수 (Wave-function) 구속이 작게 되어 나노 양자점 구조의 0차원적 특성이 저하되게 된다. 본 논문에서는 Arsenic 차단법(Interruption technique)을 이용한 수정자발형성법(Modified self-assembled method, MSAM)으로 InAs 양자점(MSAM-InAs 양자점)을 형성하고 성장 변수에 따라 광 및 구조적 특성을 평가하여 0차원 순도를 분석하였다. MSAM InAs 양자점을 성장하고 12 nm 두께의 GaAs spacer 층을 증착한 후 $600^{\circ}C$에서 30초 동안 Arsenic 분위기에서 열처리(Annealing)를 수행 한 후 다시 InAs을 증착 하였다. 이러한 과정을 5번 반복하여 높이 방향으로 형상을 개선시킨 InAs 양자점을(Vetically-controlled MSAM, VCMSAM) 성장하였다. 기존 자발형성법을 이용한 InAs 양자점과 MSAM-InAs 양자점 단일층 구조를 기준시료로 성장하였다. 상온 포토루미네슨스(Photoluminescence, PL) 실험에서 단일 MSAM InAs 양자점 및 VCMSAM 양자점 시료의 발광에너지는 각각 1.10 eV와 1.13 eV를 나타내었다. VCMSAM InAs 양자점 시료의 PL세기는 단일 MSAM 양자점보다 3.4배 증가되어, 확연히 높게 나타나는 결과를 보였다. 이러한 결과는 높이 방향으로 운반자의 파동함수 구속력이 증가하여 구속준위 (Localized states)의 전자-정공의 파동함수중첩(Overlap integral)이 개선된 것으로 설명할 수 있다. 투과전자현미경(Transmission electron microscopy) 및 원자력간 현미경(Atomic force microscopy)을 이용하여 구조적 특성을 평가하고 이를 비교 분석한 결과를 보고한다.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.53-58
• /
• 2012

In order to improve the surface hardness of transparent plastic films, an organic-inorganic hybrid coating solution was sunthesized by the sol-gel method. Coating solutions that were prepared colloidal silica (CS), poly methyl methacrylate (PMMA), vinyltrimethoxysilane (VTMS), and [3-(methacryloyloxy)]propyltrimethoxy silane (MAPTMS) was varied with synthesizing parameters such as kinds of organic silane and weight ratio of CS to PMMA. Such coating solution was bar coated on the PET film, cured, and investigated on the chemical and physical properties of coating film. The organic-inorganic hybrid coating solutions have better properties at the pencil hardness and adhesion of coating film than those of an organic material such as PMMA.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.121-121
• /
• 2016

치아는 인체중에서도 혹한 환경에서 부분으로 높은 하중과 타액과 같은 강 부식성 매체로 그 환경이 상상을 초월한다. 즉 반복적으로 가해지는 하중(응력)과 침식을 유발하는 타액과 음식물 등이다. 따라서 치아가 쉽게 파괴되거나 썩는 현상이 나타나게 된다. 이렇게 사용되다가 치아의 역할을 다하게 되면 인공치아를 사용하게 되는데 그 재료가 바로 타이타늄(Ti)이다. 생체매식재로 사용되는 Ti는 반응성이 높아 산소와 쉽게 결합하여 표면에 TiO, $TiO_2$, 및 $Ti_2O_3$와 같은 산화피막을 표면에 형성함으로써 뛰어난 부식저항성과 생체적합성을 가지며 생체에 독성이 없고 탄성계수가 골과 비슷하여 골과 임플란트 경계면에서 응력분산에 유리한 성질 등 물리적, 기계적 성질이 뛰어나 외과용 임플란트 재료로 가장 좋은 재료이다. 금속 임플란트의 생체적합도는 임플란트 재료 자체보다는 생체 내 산화막이 화학적으로 불안정할 때 부식이 발생하게 되고 그 결과 금속이온이 주위로 유리되어 조직반응을 일으키므로 금속의 표면을 덮고 있는 산화막에 의해 좌우된다. Ti는 생체불활성재료로서 매식재료로 사용할 경우 뼈와 잘 융합되는 골유착을 나타내나 골과 화학적결합은 하지 않고 골형성을 적극적으로 유도하지 못함으로 환자의 치유기간이 길어지게 된다. 이러한 이유로 골조직내 임플란트의 접합을 개선하기위한 연구가 이루어져 골과의 결합을 높이기 위해 골유착을 일으키는 Ti에 골성장을 유도하는 뼈성분인 하이드록시 아파타이트(HA)라는 물질을 플라즈마 코팅법을 사용하던가 아니면 Hanks' solution내에서 침적 후 HA도금을 하는 방법 등으로 처리하고 있다. 그러나 플라즈마 코팅법은 고온에서 처리를 행하고 Hanks' solution내에 침적할 경우 Ti표면에 밀착도가 저하되거나 합금의 상변화 등으로 인하여 표면처리 과정 중에서 내식성이 크게 감소될 수 있다. 이러한 여러 가지 코팅법을 통하여 골 유착을 증진시키기 위한 연구는 계속되고 있지만 임상적으로 사용 후 문제가 단시일에 발생되는 것도 아니고 수년이 지나야 나타나게 된다. 이러한 방법으로 코팅을 하게 되면 골과 잘 유착이 되어 자연차아와 같은 기능을 하게 된다. 따라서 이러한 문제를 최소화하는 방법이 나노구조를 표면에 형성시켜 골유착을 쉽게 함으로써 이를 개선할 수 있을 것으로 생각되어 본 강의에서는 임플란트의 문제와 사용되는 재료에 대하여 고찰하여 자연치아를 대체 할 수 있는지 알아보았다.