• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2019.04a
• /
• pp.108-108
• /
• 2019

느타리버섯은 전남 장흥군에서 병재배로 재배된 '곤지 7호' 느타리버섯 품종을 $3^{\circ}C$에서 1일간 냉각시킨 후 실험에 사용하였다. 이산화탄소 처리는 10mm 두께의 아크릴로 제작한 밀폐 챔버($40{\times}70{\times}40cm$)를 이용하여 CO2가스를 주입하여 내부의 CO2 농도를 $30{\pm}1%$로 조정하여 3시간 동안 밀폐시켰으며 $3^{\circ}C$ 저온 저장고에서 수행하였다. 처리 후 포장필름은 3처리로 하여 PVC랩, 재배농가에서 이용하는 필름인 $20{\mu}m$ OPP필름, $30{\mu}m$ OPP필름을 재료로 하여 산소투과율을 $5,000cc/m2{\cdot}day{\cdot}atm$로 조정한 필름(OPP5)을 사용하였다. PVC랩 처리는 스티로폼 트레이에 옮긴 후 균일하게 한 겹으로 둘렀고, OPP와 OPP5는 봉지에 옮겨 봉지 입구 4cm 안쪽을 비닐접착기로 열접착하여 밀봉하였으며 $3^{\circ}C$에 저장하면서 필름내부의 기체조성, 경도, 색도, 이취, 종합선도 변화를 조사하였다. 포장된 느타리버섯의 포장재 내 이산화탄소 농도는 저장초기 0.03%에서 점차 증가하여 저장 3일 후 PVC랩은 3.5~3.9%, 나머지 처리는 18%이상으로 증가하였으며 OPP필름보다 OPP5필름의 경우 포장재 내 이산화탄소 농도가 더 낮게 유지되었다. 생체중 감소는 PVC랩에서 저장 26일 후 9.9% 이하로 육안으로 보이는 시들음이 관찰되었으며 나머지 처리들은 저장 26일 후까지 1.6% 이하의 중량감소율을 보였다. 느타리버섯 갓 경도는 유지되었으며 줄기표면의 황색도 $b^*$값은 PVC랩에서는 증가 경향을, OPP나 OPP5에서는 유지 경향을 보였다. 느타리버섯의 이취 및 전체적인 품질은 무처리 후 PVC랩 포장은 저장 6일 후에 이취가 상품성 한계로 발생하였고 OPP5 포장은 포장재 중 가장 이취발생이 늦게 발생하였으며 CO2 처리에 의해 지연되는 것을 알 수 있었다. 이런 결과를 종합하여 느타리버섯의 $3^{\circ}C$ 저장 중 품질유지기간은 각 PVC랩(6일) ${\rightarrow}$ 30% CO2+PVC랩(7일) ${\rightarrow}$ OPP(10일) ${\rightarrow}$ 30% CO2+OPP(17일) ${\rightarrow}$ OPP5(20일) ${\rightarrow}$ 30% CO2+OPP5(22일)로 조사되었다. CO2처리 후 산소투과율을 $5,000cc/m2{\cdot}day{\cdot}atm$으로 조정한 미세천공(OPP5)필름이 가장 높은 전체적 품질점수를 나타내었으며 상대적으로 낮은 이취발생, 갈변과 갓무름이 적어 높은 점수를 얻는데 영향을 준 것으로 보인다.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.459-470
• /
• 2018

Cellulose nitrates were used for folklore artifacts(ornamental beads and pipes in hatstrings, frames of eyeglasses, ornamental eyeglass cases, headband ornaments, and jeogori buttons) between the 19th and 20th centuries; however, they are susceptible to cracking, crazing, embrittlement, and crumbling due to deterioration. To consolidate and adhere deteriorated cellulose nitrate folklore artifacts, water-soluble acrylic emulsion adhesives were investigated. For consolidation, Plextol D 498, which has the lowest viscosity in low concentrations, was used. In adhesive films whose glass transition temperature(Tg) is lower than room temperature, the tensile stress and modulus decreased and the strain increased; therefore, the flexibility was high. The Plextol D 498 and Plextol D 498 and Dispersion K 52 films maintained their adhesiveness and flexibility after artificial-sunlight-accelerated ageing, and Plextol D 498 and Dispersion K 52 films hardly caused yellowing. Plextol D 498 was the most stable for accelerating ageing. A low concentration of Plextol D 498 emulsion resulted in the best permeability on the surface of cellulose nitrate, compared with other acrylic emulsions. To prevent ornamental hatstrings from cracking, crazing, embrittlement, and crumbling, a Plextol D 498 emulsion was used. After applying low concentrations(1%, 3%) of the emulsion to consolidate the fragments and high concentration to adhere the fragments, the ornamental hatstrings were protected from crumbling by deterioration, and their fragments were well-adhered. To preserve it from deterioration by oxygen and humidity, the treated ornament was sealed with an oxygen-barrier film using a low-humidity oxygen scavenger.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.4
• /
• pp.491-505
• /
• 2018

As an alternative to deep geological disposal technology, which is considered as a reference concept, the domestic applicability of deep borehole disposal technology for high level radioactive waste, including spent fuel, has been preliminarily evaluated. Usually, the environment of deep borehole disposal, at a depth of 3 to 5 km, has more stable geological and geo-hydrological conditions. For this purpose, the characteristics of rock distribution in the domestic area were analyzed and drilling and investigation technologies for deep boreholes with large diameter were evaluated. Based on the results of these analyses, design criteria and requirements for the deep borehole disposal system were reviewed, and preliminary reference concept for a deep borehole disposal system, including disposal container and sealing system meeting the criteria and requirements, was developed. Subsequently, various performance assessments, including thermal stability analysis of the system and simulation of the disposal process, were performed in a 3D graphic disposal environment. With these analysis results, the preliminary evaluation of the domestic applicability of the deep borehole disposal system was performed from various points of view. In summary, due to disposal depth and simplicity, the deep borehole disposal system should bring many safety and economic benefits. However, to reduce uncertainty and to obtain the assent of the regulatory authority, an in-situ demonstration of this technology should be carried out. The current results can be used as input to establish a national high-level radioactive waste management policy. In addition, they may be provided as basic information necessary for stakeholders interested in deep borehole disposal technology.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.2
• /
• pp.76-83
• /
• 2022

Since the 3D printing mortar is exposed to the atmosphere immediately after printing, moisture is largely evaporated from the surface of the layer. The evaporation of moisture on the surface of the layer greatly causes drying shrinkage and increases the risk of cracking and damage to the structure due to drying shrinkage. This study experimentally evaluated the shrinkage behavior of the initial age using the mortar used for 3D printing. The change in shrinkage was evaluated by comparing the shrinkage of the specimen cured by the sealing method and the atmospheric exposure method. In addition, compared with the case where type 1 cement was used 100%, the shrinkage amount was evaluated when 20% of fly ash was replaced and 10% of silica fume was used. In particular, the effect of three chemical admixtures applied using 3D printing on shrinkage was evaluated experimentally. When fly ash and silica fume were used, the shrinkage amount increased by 60 - 110% compared to the case when type 1 cement was used. The application of viscosity modifiers and shrinkage reducers reduced the shrinkage by at least 18% and at most 70% depending on the curing conditions. The temperature of the specimen temporarily decreased to 15 ℃ at the beginning of curing, and the correlation between the internal temperature of the specimen and the shrinkage behavior was observed.

• Clinical and Experimental Reproductive Medicine
• /
• v.33 no.1
• /
• pp.45-52
• /
• 2006

Objective: Our purpose was to investigate the relationship between the levels of IL-6 and tumor necrosis factor-${\alpha}$ in the peritoneal fluid of women with and without endometriosis and infertile women. Methods: This study is prospective and case-control study in University hospital, enrolled thirty-four women with laparoscopic findings of minimal to severe endometriosis, and thirty-seven women with no visual evidence of pelvic endometriosis and with benign gynecologic disease. IL-6 and tumor necrosis factor-${\alpha}$ levels in peritoneal fluid were determined using commercial ELISA. IL-6 and tumor necrosis factor-${\alpha}$ concentrations were compared among women with and without endometriosis, and with infertile and fertile women, and then also compared according the revised American Fertility Society classification. Results: IL-6 and tumor necrosis factor-${\alpha}$ concentrations were higher than in the peritoneal fluid of women with endometriosis than in matched normal controls. Cyclic variations in IL-6 concentrations were seen in peritoneal fluid from patients with endometriosis: the concentrations in the secretory phase were significantly higher than those in the proliferative phase. The concentrations were higher than among of infertile women than in fertile women. A significant correlation between IL-6 and tumor necrosis factor-${\alpha}$ concentrations and endometriosis stage III and IV was noted. Conclusion: Increased levels of IL-6 and tumor necrosis factor-${\alpha}$ in patients with endometriosis in the peritoneal fluid may be relate to the pathogenesis of endometriosis suggesting that partially contribute to the disturbed immune regulation observed in patients with endometriosis.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.2
• /
• pp.26-29
• /
• 2011

Purpose: The general test method of the Korean Pharmacopeia specifies the test method on the clauses of quality control after manufacturing. According to KFDA Guidance for Medicines, standards of residual solvents regulates the maximum permissible dose of acetonitrile as 400 ppm, ethanol as 5,000 ppm, and acetic acid as 5,000 ppm. This study aims at identifying the type of resiual solvents in the final [F-18]FDG vial of an automatic synthesizer and measure its residual quantity. Materials and Methods: The center carried out residual solvents test of [F-18]FDG injection using Agilent Technologies 7890A with a Flame Ionization Detector. The column of Agilent Technologies 7890A used in measuring of residual solvents was CP WAX column ($30m{\times}0.53mm{\times}1.0{\mu}m$) and analysis condition was split mode 1:1 at the initial temperature $70^{\circ}C$ which was increased $20^{\circ}C/minute$ after two minutes and maintained at the final $140^{\circ}C$ for two minutes. The analysis method was as following: Firstly, ethanol-acetonitrile-acetic acid mixture was classified into four types of concentration (250-25-250 ppm, 1,000-100-1,000 ppm, 3,000-300-3,000 ppm, and 6,000-600-6,000 ppm), and $1.0{\mu}L$ of each type of concentration was injected into gas chromatography followed by an analysis of its peak domain. Then, a calibration-curve by the external standard method was drawn based on the analysis result. Results: While ethanol and acetonitrile were detected in TRACERlab MX, FASTlab had additional acetic acid. The residual quantity of the ethanol-acetonitrile-acetic acid mixture evaluated using the calibration-curve was average 72 ppm ethanol, 54 ppm acetonitrile, and 1030 ppm acetic acid for FASTlab, whereas average 439 ppm ethanol and 79 ppm acetonitrile for TRACERlab MX. This indicated that both of them were within the maximum permissible dose. Conclusion: Solvent residues in the [F-18]FDG injection were all within maximum permissible doses and proper to be used to examine a patient. The result indicated that types and quantities of solvent resides of radioactive pharmaceuticals vary depending on the automatic synthesizer.

• Analytical Science and Technology
• /
• v.28 no.3
• /
• pp.228-235
• /
• 2015

The efficiency and applicability of the solid phase extraction disk method in a ²²⁶Ra analysis were examined by the gamma ray spectrometer (GRS) method using a Marinelli beaker and the liquid scintillation counter (LSC) method for groundwater. The recovered ²²⁶Ra, which was filtered by the solid phase extraction disk, was analyzed using gamma ray spectrometer The disks, which were pretreated for caulking the daughter nuclide, were sealed with polyethylene film. Distilled water was used for the blank value of the ²²⁶Ra activity. The recovery values of ²¹⁴Bi and ²¹⁴Pb in the solid phase extraction disk, which used ²²⁶Ra standard material, were 80% (295.21 Kev) and 104% (351.92 Kev), respectively, which were higher than 75% determined by the LSC. The injection of nitrogen gas into the measuring chamber reduced the interference values by about 10%. The detection limits of the ²²⁶Ra activity in a blank sample of 5 L were 0.17~0.40 pCi/L after 80,000 seconds of measuring time. The relationship of the ²²⁶Ra activity in the solid phase extraction disk method and in the LSC method in seven groundwater samples showed a correlation coefficient value 0.987, which implies the applicability of the solid phase extraction disk method. The results showed that ²²⁶Ra activity in groundwater using the solid phase extraction disk method has the following benefits: simple pretreatment, time saving, high recovery values, a low detection limit, and so on. Compared with the LSC method and the GRS method using the Marinelli beaker for the ²²⁶Ra analysis, the solid phase extraction disk method could be useful in groundwater samples with low levels of activities of radionuclides because the method is not restricted by the volume of the sample.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.527-535
• /
• 2020

The purpose of this study was to establish a simple vitrification protocols to preserve animal cell lines derived from tissues of livestock that could be recultured. Bovine oviduct epithelial cells (BOEC) were used for the vitrification process using a 0.25 ml straw to increase cryopreservation efficiency. BOEC was cultured from the oviduct of 3.5-day estrus state, and the commercially available polyampholyte StemCell Keep^TM was used as a cryoprotective agent. Using different concentrations, the viability rates of BOEC in 5, 10, 25, 50, 75, and 100% in freezing media were investigated. Survivability was determined using a differential staining technique using a trypan blue test and a CYTO-13/PI staining protocol. The viability rates of BOEC in the trypan blue test were 5.6±11.8, 12.5±7.2, 53.0±2.7, 85.1±6.9, 79.8±0.6, and 60.7±6.7% with a respective concentration of StemCell Keep^TM. The viability rates in CYTO-13/PI staining were 4.6±2.5, 30.8±12.1, 58.4±2.5, 85.5±1.2, 79.8±0.6, and 71.2±1.2%, respectively. These results indicate that BOEC could be preserved with StemCell Keep^TM without toxicity in a 0.25-ml straw. The optimal concentration of vitrification solution with StemCell Keep^TM was determined to be 50% and can be considered as a proper preservation method for cryobanking.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.1-10
• /
• 2018

Recently, there has been rapid development in the field of flexible electronic devices, such as organic light emitting diodes (OLEDs), organic solar cells and flexible sensors. Encapsulation process is added to protect the flexible electronic devices from exposure to oxygen and moisture in the air. Using numerical simulation, we investigated the effects of the encapsulation layer on mechanical stability of the silicon chip, especially the fracture performance of center crack in multi-layer package for various loading condition. The multi-layer package is categorized in two type - a wide chip model in which the chip has a large width and encapsulation layer covers only the chip, and a narrow chip model in which the chip covers both the substrate and the chip with smaller width than the substrate. In the wide chip model where the external load acts directly on the chip, the encapsulation layer with high stiffness enhanced the crack resistance of the film chip as the thickness of the encapsulation layer increased regardless of loading conditions. In contrast, the encapsulation layer with high stiffness reduced the crack resistance of the film chip in the narrow chip model for the case of external tensile strain loading. This is because the external load is transferred to the chip through the encapsulation layer and the small load acts on the chip for the weak encapsulation layer in the narrow chip model. When the bending moment acts on the narrow model, thin encapsulation layer and thick encapsulation layer show the opposite results since the neutral axis is moving toward the chip with a crack and load acting on chip decreases consequently as the thickness of encapsulation layer increases. The present study is expected to provide practical design guidance to enhance the durability and fracture performance of the silicon chip in the multilayer package with encapsulation layer.

• The Korean Journal of Food And Nutrition
• /
• v.28 no.3
• /
• pp.422-427
• /
• 2015

This study was carried out to investigate the microbiological contamination levels of Dutch coffee products marketed in Korea. The temperature conditions during distribution and storage were also considered in this experiment. Retailed Dutch coffee were purchased from regional cafes, that is, these were self-blended by the cafes, and the marketed products were purchased from department stores and from Internet sites. The 21 samples were blended in a coffee house and 9 were obtained from department stores or were delivered from internet sites. House blended Dutch coffee contained $35.2{\pm}15.8CFU/mL$ of general bacteria, and this increased to $78.4{\pm}29.7CFU/mL$ at room temperature or $51.2{\pm}32.1CFU/mL$ after refrigeration for 5 days. These almost reached the highest criteria level for the Korea Food Sanitation Law. After 10 days, the count increased to $98.5{\pm}58.4CFU/mL$ at room temperature and $86.7{\pm}44.2CFU/mL$ at refrigeration temperature. In the Dutch coffee for distribution, $39.6{\pm}20.1CFU/mL$ of general bacteria were detected, but these did not increase after 5 days or 10 days both for room temperature and under refrigeration. The Coliform group was not found in any kind of Dutch coffee, and Fungi was founded in 60% of the Dutch samples purchased in coffee houses, department stores, and shopping sites mall. On day 0 day, $2.6{\pm}1.7CFU/mL$ of fungi were detected in the coffee house Dutch, and it did not increase significantly during the storage period at room and in a cold temperature. $3.5{\pm}3.4CFU/mL$ of fungi were detected in the Dutch coffee for distribution, and it didn't increase during further storage under any temperature.