• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2012년도 제46차 학술발표회
• /
• pp.41-41
• /
• 2012

고급 스포츠웨어와 이너웨어 등에 많이 사용되고 있는 나일론/폴리우레탄 혼방제품은 염색에 있어서 Grin-through 현상, 인공피혁의 염료 이염 현상 등 많은 문제들이 존재한다. 본 연구의 나일론과 폴리우레탄 복합소재에서 나타나는 염색거동을 고찰하고 분석하여, 폴리우레탄 복합소재의 염색성을 개선하기 위하여 실시하였다. 폴리우레탄 복합소재는 해성분이 용출되지 않은 나일론 초극세사 소재에 폴리우레탄 수지를 함침하여 인공피혁과 같은 느낌을 주도록 직접 제조하였다. 제조된 폴리우레탄 함침 나일론 초극세사 소재의 해성분을 용출하였고, Red 색상의 밀링형 산성 염료, 함금속 염료와 반응성 염료에 따라 달라지는 염색특성 및 세탁 견뢰도 등을 고찰하였다. 본 연구를 통하여 다음과 같은 실험결과를 얻을 수 있었다. 나일론 초극세사와 폴리우레탄 수지를 준비하여 습식공정을 통해 인공피혁을 제조한 함침 소재를 알칼리 감량하였고, 감량률은 15~17% 정도로서 대부분의 해성분이 용출됨을 확인하였다. PPG와 PTMG로 구성된 폴리올을 기반으로 한 폴리우레탄 함침 피혁과 PTMG를 단독으로 사용한 함침 피혁의 염색성을 비교한 결과, PPG+PTMG 타입이 더 우수한 염색성을 나타내었다. 특히 밀링 타입과 함금속 타입 염료의 경우는 거의 2배 이상의 흡진율과 겉보기 색농도를 나타내었다. 한편, 반응성 염료의 경우는 두 종류의 폴리우레탄 필름에 거의 염착되지 않았기 때문에 앞으로의 염색실험에서 제외하였다. 견뢰도 측면에서는 각각의 피염물의 등급은 거의 유사하게 나타남을 확인하였다. 이상과 같은 결과로부터, 인공피혁 제조시 PPG+PTMG 타입의 폴리우레탄 수지를 사용하여 함침시 더 높은 색강도와 염착률을 얻을 수 있음을 알았다. 사용하는 염료의 종류를 좀 더 다양하게 하여 실험을 실시하고 폴리우레탄의 물성 및 분석 등의 추가적인 연구가 진행된다면, 인공피혁의 염색시에 발생하는 여러 가지 문제점들을 해결할 수 있을 것이다.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.313-320
• /
• 2006

The present study is to analyze the thermoelectric properties of $Bi_{0.4}Sb_{1.6}Te_3$ thermoelectric materials fabricated by the mechanical grinding process. The $Bi_{0.4}Sb_{1.6}Te_3$ powders were prepared by the combination of mechanical milling and reduction treating methods using simply crushed pre-alloyed $Bi_{0.4}Sb_{1.6}Te_3$ powder. The mechanical milling was carried out using the tumbler-ball mill and planetary ball mill. The tumbler-ball milling had an effect on the carrier mobility rather than the carrier concentration, whereas, the latter on the carrier concentration. The specific electric resistivity and Seebeck coefficient decreased with increasing the reduction-heat-treatment time. The thermal conductivity continuously increased with increasing the reduction-heat-treatment time. The figure of merit of the $Bi_{0.4}Sb_{1.6}Te_3$ sintered body prepared by the mechanical grinding process showed higher value than one of the sintered body of the simply crushed powder.

• 한국분말재료학회지
• /
• 제17권4호
• /
• pp.302-311
• /
• 2010

In this research, the refinement behavior of the coarse magnesium powders fabricated by gas atomization was investigated as a function of milling time using a short duration high-energy ball milling equipment, which produces fine powders by means of an ultra high-energy within a short duration. The microstructure, hardness, and formability of the powders were investigated as a function of milling time using X-ray diffraction, scanning electron microscopy, Vickers micro-hardness tester and magnetic pulsed compaction. The particle morphology of Mg powders changed from spherical particles of feed metals to irregular oval particles, then platetype particles, with increasing milling time. Due to having HCP structure, deformation occurs due to the existence of the easily breakable C-axis perpendicular to the base, resulting in producing plate-type powders. With increasing milling time, the particle size increased until 5 minutes, then decreased gradually reaching a uniform size of about 50 micrometer after 20 minutes. The relative density of the initial power was 98% before milling, and mechanically milled powder was 92~94% with increase milling time (1~5 min) then it increased to 99% after milling for 20 minutes because of the change in particle shapes.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.291-296
• /
• 2012

In the present work, Al-$B_4C$ composite powders were fabricated using a mechanical milling process and its milling behaviors and mechanical properties as functions of $B_4C$ sizes ( $100{\mu}m$, 500 nm and 50 nm) and concentrations (1, 3 and 10 wt.%) were investigated. For achieving it, composite powders and their compacts were fabricated using a planetary ball mill machine and magnetic pulse compaction technology. Al-$B_4C$ composite powders represent the most uniform dispersion at a milling speed of 200 rpm and a milling time of 240 minutes. Also, the smaller $B_4C$ particles were presented, the more excellent compositing characteristics are exhibited. In particular, in the case of the 50 nm $B_4C$ added compact, it showed the highest values of compaction density and hardness compared with the conditions of $100{\mu}m$ and 500 nm additions, leading to the enhancement its mechanical properties.

• Korean Chemical Engineering Research
• /
• 제56권2호
• /
• pp.191-203
• /
• 2018

이 연구는 각각 크기와 재질이 다른 3 가지 종류의 분쇄 매체를 이용하여 회전속도와 밀링 시간의 따른 구리 (Cu) 분말의 형상변화의 과정에 미치는 영향을 관찰하고, 볼 움직임의 DEM시뮬레이션을 행하였다. 전동볼밀에서 볼 움직임의 3차원 시뮬레이션을 통해 분쇄 메커니즘을 규명하기 위하여 분쇄매체의 힘, 운동에너지, 매체 운동속도 등을 계산하였다. 시뮬레이션에서는 회전속도, 볼 재질, 운동속도, 마찰계수 등을 실제 실험조건과 동일하게 조건을 맞추어 투입되는 에너지의 변화량도 계산하였다. 주사전자현미경 결과를 살펴보면 볼 직경이 작을 때 입자형상이 불규칙한 형태에서 구형 형태로 변화하는 것을 알 수 있었다.

• 한국분말재료학회지
• /
• 제29권1호
• /
• pp.34-40
• /
• 2022

Recently, high-entropy carbides have attracted considerable attention owing to their excellent physical and chemical properties such as high hardness, fracture toughness, and conductivity. However, as an emerging class of novel materials, the synthesis methods, performance, and applications of high-entropy carbides have ample scope for further development. In this study, equiatomic (Hf-Ti-Ta-Zr-Nb)C high-entropy carbide powders have been prepared by an ultrahigh-energy ball-milling (UHEBM) process with different milling times (1, 5, 15, 30, and 60 min). Further, their refinement behavior and high-entropy synthesis potential have been investigated. With an increase in the milling time, the particle size rapidly reduces (under sub-micrometer size) and homogeneous mixing of the prepared powder is observed. The distortions in the crystal lattice, which occur as a result of the refinement process and the multicomponent effect, are found to improve the sintering, thereby notably enhancing the formation of a single-phase solid solution (high-entropy). Herein, we present a procedure for the bulk synthesis of highly pure, dense, and uniform FCC single-phase (Fm3m crystal structure) (Hf-Ti-Ta-Zr-Nb)C high-entropy carbide using a milling time of 60 min and a sintering temperature of 1,600℃.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.41-44
• /
• 2009

A multi-stage gear mold including gears of 2mm and 1.5mm diameter was designed and machined in this research for developing micro gear mold manufacturing technology with micro endmill. Mechanical shapes having differential micro teeth were analyzed to be formed as designed and processing conditions were optimized by analyzing machined surface chip and cutting force. Based on the results, a prototype of micro multi-stage gear mold was manufactured.

• 한국분말재료학회지
• /
• 제21권4호
• /
• pp.307-312
• /
• 2014

This study is focused on investigating the relation between the particle size of silver flake powder and mechanical milling parameters. Mechanical milling parameters such as ball size, impeller rotation speed and milling time of the attrition ball-mill were controlled to produce silver flake powder. The particle size of the silver flake powder increased with increasing ball size and impeller rotation speed. The change of the particle size of the silver flake powder with mechanical milling parameters was analyzed based on balls motion in the mill container of the attrition ball-mill. The silver flake particles were formed at the elastic deformation area of the ball due to the collision between balls. The change of the particle size of the silver flake powder with mechanical milling parameters well consists with the change of the collision energy of ball with parameters mentioned above.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.30-35
• /
• 2008

As demands for being economical, precise drilling process is on the increase. Therefore, the objective of this study is to develop a step cutter that can be controllable through micro dimension and can be changed from separate manufacturing processes of drilling and boring into an integrated one. In order to attain this object the step cutter is designed with a 3D geometric modeling and the design could be modified easily by using parametric modeling methodology. Also, collision is not occurred during manufacturing process because of cutting simulation. The step cutter is assembled by parts made up of 5-axis machining and sintering. Validation tests are accomplished. They show that developed cutter has characteristics such as reduction of machining time as well as the good surface roughness of the machined hole. Indeed, reliability could be obtained from a durability test.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.536-542
• /
• 2002

There are two important variables in machining process control, which are feed and cutting speed. In this work, a two degree-of-freedom controller is designed and implemented to achieve on-line cutting force control and position control based on the modelling of cutting process dynamics which are established through step response test. Two schemes are proposed and implemented. The first is feed control under the constant spindle speed and spindle speed control under the constant feed speed. The second is a simultaneous control of feed and spindle speed. The last performs a position control under the constant cutting force. Those are confirmed to work properly. Especially the latter shows a faster response.