• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.584-588
• /
• 2019

The catalytic combustion of particulate matter (PM) is one of the key technologies to meet emission standards of diesel engine system. Therefore, we herein suggest Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst. They were produced by the electrospinning method. FE-SEM, EDS mapping, XRD, XPS were studied to investigate the crystal and morphological structures of loaded Ag particles and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst. Following the catalytic soot oxidation, we found that the Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskiteweb catalyst showed the higher catalytic activities (e.g., $T_{50}=490^{\circ}C$) than the only $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst (e.g., $T_{50}=586^{\circ}C$). Thus, this finding suggests that Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst can be a promising candidate for enhancing the soot oxidation.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.663-670
• /
• 2018

H13 tool steels are widely used as metallic mold materials due to their high hardness and thermal stability. Recently, many studies are undertaken to satisfy the demands for manufacturing the complex shape of the mold using a 3D printing technique. It is reported that the mechanical properties of 3D printed materials are lower than those of commercial forged alloys owing to micropores. In this study, we investigate the effect of microstructures and defects on mechanical properties in the 3D printed H13 tool steels. H13 tool steel is fabricated using a selective laser melting(SLM) process with a scan speed of 200 mm/s and a layer thickness of $25{\mu}m$. Microstructures are observed and porosities are measured by optical and scanning electron microscopy in the X-, Y-, and Z-directions with various the build heights. Tiny keyhole type pores are observed with a porosity of 0.4 %, which shows the lowest porosity in the center region. The measured Vickers hardness is around 550 HV and the yield and tensile strength are 1400 and 1700 MPa, respectively. The tensile properties are predicted using two empirical equations through the measured values of the Vickers hardness. The prediction of tensile strength has high accuracy with the experimental data of the 3D printed H13 tool steel. The effects of porosities and unmelted powders on mechanical properties are also elucidated by the metallic fractography analysis to understand tensile and fracture behavior.

• Journal of Life Science
• /
• v.28 no.12
• /
• pp.1424-1431
• /
• 2018

We prepared flocculated detritus-like organic marine snow originating from various organisms by fermentation using microorganisms; this fermented organic material was fed to the leptocephali of the eel (Anguilla japonica) to investigate whether or not such organic matter was an appropriate food source for the larvae. A strain was isolated from a biofloc technology system used to culture fish, and seven types of organic material from hen's egg, eel muscle, tuna muscle, lugworm, shrimp, manila clam, mussel, and sea squirt were fermented using isolated bacteria (Bacillus sp.). The fermented matter did not show any specific form and was larger than $10-20{\mu}m$ but no more than $100{\mu}m$ in size. Four diets (A-D) were prepared using the various fermented products, and the larvae were fed the prepared food from 20 days after hatching. The leptocephali fed the A, B, and C diets survived until 37, 39, and 37 days after hatching, respectively. However, the leptocephali fed the D diet survived for 60 days after hatching. The protein content of each diet was very similar, but the n-3 HUFA concentration in the D diet was approximately twice as high as that of the others.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.44-52
• /
• 2018

In this study, copper was recovered from copper containing sludge by selectively controlling electro-refining process conditions in copper sulfate electrolyte solution. Electro-refining process was performed by LSV (Linear Sweep Voltammetry) result according to copper sulfate electrolyte solution concentration, applied current density, additive type and concentration. SEM (Scanning Electron Microscope) and PSA (Particle Size Analyzer) were used to analyze the shape and size of copper powder. In the 0.1 ~ 0.4 M copper sulfate electrolyte solution without organic additives, the copper powder size decreased as the applied current density became closer to the limiting current density and the copper powder size tended to decrease in 0.2 ~ 0.3 M copper sulfate electrolyte solution. In addition, when the shape and size of the copper powder were analyzed by adding various types and concentrations of organic additives to the previous experimental, fine spherical copper powder having the smallest size (nm) was obtained under the condition of cellulose type additive 2,000 ppm.

• Journal of Korea Foundry Society
• /
• v.39 no.2
• /
• pp.26-31
• /
• 2019

In this study, the mechanical characteristics and microstructure of hypereutectic Al-17Si-5Fe extruded alloys prepared by a rapid solidification process (RSP) were investigated. The hypereutectic Al alloy was fabricated by means of RSP and permanent casting. For RSP, the Al alloy melted at $920^{\circ}C$, cooling the specimens at a rate of $10^6^{\circ}C/s$ when the RSP was used, thus allowing the refining of primary Si particles more than when using permanent casting, at a rate of about 91%. We tested an extrusion RSP billet and a permanent-cast billet. Before the hot-extrusion process, heating to $450^{\circ}C$ took place for one hour. The samples were then hotextruded with a condition of extrusion ratio of 27 and a ram speed of 0.5 mm/s. Microstructural analyses of the extruded RSP method and the permanent casting method were carried out with OM and SEM-EDS mapping. The mechanical properties in both cases were evaluated by Vickers micro-hardness, wear resistance and tensile tests. It was found that when hypereutectic Al-17Si-5Fe alloys were fabricated by a rapid solidification method, it becomes possible to refine Si and intermetallic compounds. During the preparation of the hypereutectic Al-17Si-5Fe alloy by the rapid solidification method, the pressure of the melting crucible was low, and at faster drum speeds, smaller grain alloy flakes could be produced. Hot extrusion of the hypereutectic Al-17Si-5Fe alloy during the rapid solidification method required higher pressure levels than hot extrusion of the permanent mold-casted alloy. However, it was possible to produce an extruded material with a better surface than that of the hot extruded material processed by permanent mold casting.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.2
• /
• pp.37-43
• /
• 2019

This study investigated electrical conductivity, electromagnetic shielding effectiveness, and mechanical property to improve electromagnetic shielding performance of high performance fiber reinforced cementitious composites (HPFRCC). Steel fiber, steel slag and carbon black as a conductive material were incorporated into the HPFRCC mixes. In addition, 2% CNT solution which was produced by dispersing multi-wall carbon nanotube (MWCNT) into water was used as a conductive material. In the test results, electrical conductivity of HPFRCC specimens was very low except for the specimen incorporating 1% carbon black. Micro structure of cement matrix was changed as the curing time increased, which negatively affected the conductive network of HPFRCC. In case of HC1 specimen showing a conductive network (0.083 S/cm), the electrical conductivity of the specimen after being dried at $60^{\circ}C$ for 72 hours to exclude the effect of water on electrical conductivity was significantly reduced to 0.0003 S/cm. The most important parameter of electromagnetic shielding effect was found to be a steel fiber while the effect of carbon black and steel slag was very few. The correlation between electrical conductivity and electromagnetic shielding effect does not seem to be clear.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.296-303
• /
• 2021

The objective of this study is to investigate the applicability of a Cu-supported honeycomb catalyst as a catalyst for decomposition of a low toxic liquid propellant based on ammonium dinitramide (ADN). A mixture of copper, lanthanum, and alumina was supported on the honeycomb support by wash coating to prepare a Cu-La-Al/honeycomb catalyst. We elucidated that the effect of metal loading on the physicochemical properties of Cu-La-Al/honeycomb catalyst and catalytic performance in decomposition of the ADN-based liquid propellant. As the number of wash coatings increased, the amount of active metal Cu was increased to 4.1 wt%. The BET surface area of the Cu-La-Al/honeycomb catalyst was in the range of 3.1~4.1 ㎡/g. The micropores were hardly present in Cu-La-Al/honeycomb catalysts, however, the mesopores and macropores were well developed. The Cu (2.7 wt%)-La-Al/honeycomb catalyst exhibited the highest activity in the decomposition of the ADN-based liquid propellant, which is attributed to the largest surface area, the largest pore volume, and the well-developed mesopores and macropores.

• Journal of Korea Foundry Society
• /
• v.41 no.2
• /
• pp.127-131
• /
• 2021

Based on its good compatibility with high-temperature environments, the Ti-48Al-2Cr-2Nb alloy is used for high-temperature materials of industrial equipment. In this study, a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel was fabricated by a vacuum centrifugal casting method. The conditions that prevent misrun defects of the turbocharger turbine wheel blade from centrifugal casting using alumina molds were investigated. The microstructure of the alloy prepared by vacuum centrifugal casting was studied by means of optical microscopy (OM), with a micro-Vickers hardness analyzer (HV), by X-ray diffraction (XRD) and by SEM-EDS. The HV and SEM-EDS examinations of the as-cast Ti-48Al-2Cr-2Nb alloy showed that the thickness of the oxide layer (α-case) was typically less than 50 ㎛. At a high preheating temperature of 1,100℃, a moderate RPM of 260, and with an alumina mold with a large gate size, there were almost no misrun defects. Therefore, it was confirmed that a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel with fewer misrun defects could be achieved through a high preheating temperature, a moderate RPM, a large gate size and an alumina mold to suppress the formation of alpha-case components.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.48 no.2
• /
• pp.169-180
• /
• 2022

Streptococcus sp. is generally known as a strain that produces hyaluronic acid. In this study, we focused on ingredients other than hyaluronic acid among several metabolites produced by Streptococcus sp. during cultivation. The hair experimental sample (HAIRCLE^TM) was prepared with Streptococcus sp. culture filtrate under the condition that hyaluronic acid was not produced and the effect on the hair was identified. Tensile strength of hair was tested with a universal testing machine (UTM). Surface properties of a hair were examined with an atomic force microscope (AFM). Our results suggest that HAIRCLE^TM could prevent damage to a hair such as destroyed-cuticle, increased-faction force, and broken-hair. Furthermore, hair-related experiments confirmed that HAIRCLE^TM could promote the expression of hair growth factors VEGF, HGF, and Wnt10b and mitigate male hair loss by inhibiting androgen receptors and TGF-β2 expression. In addition, it was confirmed that the expression of barrier-related factors (INV, CLDN-1) was increased for oxidative stress, and the COX-2 expression, an inflammatory factor, was inhibited, thereby improving damaged scalp barriers and alleviating induced inflammation.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.91-97
• /
• 2022

The wettability and rheological properties of solder paste with the size of the solder powder were evaluated. To formulate the solder paste, three types of solder powder were used: T4 (20~28 ㎛), T5 (15~25 ㎛), and T6 (5~15 ㎛). The viscosities of the T4, T5, and T6 solder pastes at 10 RPM were 155, 263, and 418 Pa·s, respectively. After 7 days, the viscosity of the T4 solder paste slightly increased by 2.6% and that of T5 was increased by 20.6%. The viscosity of the T6 solder paste after 7 days could not be measured due to high viscosity. The viscosity variation with solder particle size also affected on the printability of the solder. In the case of the T4 solder paste, printability, slump, bridging, and soldering properties were excellent. On the other hand, T5 showed slight dewetting and solder ball defects. Especially, T6, which the smallest powder size, showed poor printability and dewetting at the edge of solder.