• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1982-1984
• /
• 1996

In this paper, we have evaluated the physical characteristicsof the Pt/Cr bilayer, fabricated the micro hot plate by using the Pt/Cr bilayer and E-beam evaporated oxide as a passivation layer, and simulated the thermal distribution by using the commercial software FIDAP. From the researches the sheet resistance of Pt/Cr bilayer didn't be affected by the Cr layer thickness. This results was considered due to the Cr-oxide resided at the interface between Pt and Cr layer. After manufacturing the hot plate, we measured its temperature by type k thermo-couple and I.R. thermo-vision system. In those experiments, the emission coefficient( ${\varepsilon}$ ) of the E-beam evaporated oxide was 0.5 and the temperature of centural region was reached about $305\;^{\circ}C$ at 1.3 watts. The temperature simulation obtained by FIDAP commercial package stewed that the temperature of centural region was about $311\;^{\circ}C$ after 5 sec.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1177-1182
• /
• 2003

The porous sensing materials for BaTiO$_3$ gas sensors were fabricated by adding the graphite powders. The crystalline structure and microstructure of the porous BaTiO$_3$-based ceramics were studied. All the sintered bodies showed a tetragonal perovskite structure. The porosity increased with increasing graphite contents. This is mainly due to an enhanced evolution of CO and $CO_2$ gases resulting from the exothermic reactions of graphite and oxygen during the sintering. It was found that the discrepancy in the resistivities measured in air and CO atmospheres at high temperatures (>∼20$0^{\circ}C$) became remarkable with increasing temperature. The sensitivity of CO gas increased with porosity, since the reactions between CO gas and $O_2$$^{[-10]}$ and between CO gas and $O^{[-10]}$ are active due to the formation of many reaction sites. The porous BaTiO$_3$-based ceramics could be promising as a sensing material for CO gas sensors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.95-98
• /
• 2002

전력선 통신 blocking filter용 자심 재료를 개발하기 위해서 MnO 24 mol%, ZnO 25 mol% and $Fe_{2}O_{3}$ 51 mol% 의 기본조성에 $MoO_{3}$, $SiO_{2}$, CaO를 첨가하여 $1350^{\circ}C$에서 대기압 상수 A를 7.8롤 고정하고 소결하여 미세구조를 제어하였으며 기본 조성에 $MoO_{3}$ 400 ppm, $SiO_{2}$ 100 ppm and CaO 200 ppm을 첨가한 경우 평균 입경 $25{\mu}m$ 의 균일한 결정립으로 구성된 미세구조를 얻었고 기공의 감소에 의한 치밀화로 $4.98g/cm^{2}$의 고밀도화가 이루어 졌다. 또한 소결체의 균일한 미세구조와 고밀도화로 인해서 8221(${25^{\circ}C}$, 1 KHz) 의 가장 높은 투자율 특성을 나타냈다. 시편의 온도가 증가함에 따라 투자율이 증가되어 ${110^{\circ}C}$에서 13904의 거대 투자융이 측정되었고, 코일의 인가주파수가 1 KHz에서 1 MHz까지 증가됨에 따라 최고 ${102^{\circ}C}$까지 시편 온도가 상승하였다. 가장 높은 투자율 특성을 나타낸 ferrite 코어를 사용하여 단상 및 3상용 블로킹 필터의 감쇄율을 측정한 결과 현재 국내의 전력선 통신용 주파수 대역으로 규정되어 있는 10 KHz ~ 450 KHz 대역에서 각각 -46.46 dB와 -73.9 dB의 최고 값을 얻었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.6
• /
• pp.271-276
• /
• 2020

In this study, an amorphous SiC block was manufactured using polycarbosilane (PCS), an organosilicon polymer. The dense SiC blocks were easily fabricated in various shapes via pyrolysis at 1100℃, 1200℃, 1300℃, 1400℃ after manufacturing a PCS molded body using cured PCS powder. Physical and chemical properties were analyzed using a thermogravimetric analyzer (TGA), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and universal testing machine (UTM). The prepared SiC block was decomposed into SiO and CO gas as the temperature increased, and β-SiC crystal grains were grown in an amorphous structure. In addition, the density and flexural strength were the highest at 1.9038 g/㎤ and 6.189 MPa of SiC prepared at 1100℃. The manufactured amorphous silicon carbide block is expected to be applicable to other fields, such as the previously reported microwave assisted heating element.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2544-2546
• /
• 1998

The electrical and physical charateristics of Pt-Co alloy thin films on $Al_2O_3$ substrate, deposited by r.f cosputtering respectively, were analyzed with thickness of thin films ($1700{\sim}10000{\AA}$) and increasing annealing temperature ($800{\sim}1000^{\circ}C$). At input power of Pt : 4.4 W/$cm^2$, Co : 6.91 W/$cm^2$, working vacuum of 10 mTorr and annealing conditions of $1000^{\circ}C$) and 60 min, the resistivity and sheet resistivity of Pt-Co thin films with thickness of $3000{\AA}$ was $15{\mu}{\Omega}{\cdot}cm$ and 0.5 ${\Omega}/{\square}$, respectively. The TCR value of Pt-Co alloy thin films was measured with various thickness of thin films and annealing conditions. The optimum TCR value of 3850 ppm/$^{\circ}C$ in temperature range($200{\sim}400^{\circ}C$) is gained under conditions $3000{\AA}$ of thin films thickness and $1000^{\circ}C$ of annealing temperature. The thermal charateristics of Pt-Co micro heaters were analysed with Pt-Co RTD integrated on the same substrate. In the analysis of characteristics of Pt-Co micro heaters, the Pt-Co micro heaters with thickness of $3000{\AA}$ and annealing temperature of $1000^{\circ}C$ had a good linearity and temperature is up to $468.2^{\circ}C$ with 2.1 watts of the heating power.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.568-574
• /
• 2007

Crack-free dried gel monoliths of the composition $Li_2O1{\cdot}7Al_2O_3{\cdot}8.6SiO_2$ have been prepared as a precursor of transparent glass-ceramic by the hydrolysis and polycondensation of mixed metal alkoxides in solutions containing N,N-dimethylformamide as the drying control chemical additive, alcohols, and water. It was investigated that activation energy for gelation according to the variation of water concentration ranged from 13 to 14 kcal/mol. Only when the amount of water for gelation was 3 times higher than the stoichiometric amount, monolithic dry gels were successfully prepared after drying at $70{\sim}75^{\circ}C$ and at a rate of 0.1~0.3%/h. The specific surface area, the pore volume, the average pore diameters of dried gel at $180^{\circ}C$ were about $239.40m^2/g$, 0.001~0.03 mL/g, and $145.62{\AA}$, respectively. It showed that the dried monolithic gel had a porous body. The DTA curve had the first exothermic peak around $800^{\circ}C$ and the 2nd peak around $980^{\circ}C$, which may correspond to crystallization of the gel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.179-179
• /
• 2008

$BaTiO_3$를 기본조성으로 하는 PTC 써미스터는 Curie 온도이상에서 저항이 급격히 상승하는 산화물 반도체 세라믹이다. 이러한 성질을 이용하여 degaussing 소자, 정온 발열체, 온도센서, 전류 제한소자 등 상업적으로 여러 분야에서 연구되고 있다. 또한 원가절감 등을 위하여 Ni 내부전극을 사용하여 환원 분위기에서 소결하는 칩 타입에 대한 연구가 진행되고 있다. 본 연구에서는 Sm 함량(0.1at%~1.0at%)을 달리한 $BaTiO_3$(Si, Mn, Ca) 계를 선택하여 3%$H_2/N_2$ 분위기에서 1200~$1260^{\circ}C$, 2h 소결한 후 공기 중에서 재산화 처리하고 재산화 시간에 따른 PTC 특성 변화에 대하여 고찰하였다. 재산화 온도와 시간은 각각 $800^{\circ}C$와 0.5h~10h으로 하였다. Sm 함량을 달리하여 환원 분위기에서 소결한 시편의 미세구조와 PTC 특성과의 상관관계를 관찰한 결과, 소결온도가 낮을수록 PTC 특성은 좋아졌으며, 상온 비저항은 Sm 함량이 높아질수록 낮아졌다. 또한 Sm 함량이 높아질수록 jumping ratio$(R_{max}/R_{25^{\circ}C})$는 낮아졌다. 재산화 시간에 따른 PTC 특성은 다소 떨어졌지만 소결온도에 따라 달리 나타났다. Jumping ratio$(R_{max}/R_{25^{\circ}C})$는 Sm을 0.7 at% 첨가한 계에서 재산화를 1시간 처리한 시편에서 가장 우수하였다.

• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.9-15
• /
• 1994

Catalytic combustible gas sensors were fabricated by using ${\gamma}-Al_{2}O_{3}$ with large surface area and noble metal catalysts. The optimum conditions for ${\gamma}-Al_{2}O_{3}$ fabrication were investigated by DT/TGA and XRD analyses and it was found that fabricated ${\gamma}-Al_{2}O_{3}$ had superior value as surface area of $215.5m^{2}/g$. Gas sensors were manufactured and tested to inflammable gases by using Pt coil as a heater and temperature sensing part, fine ${\gamma}-Al_{2}O_{3}$ powder as a bead material and Pt, Pd noble metal powder as a catalyst. From the results, fabricated sensor showed good sensitivity to LPG and LNG of 20mV/l000ppm, 6.5mV/l000ppm respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.63-68
• /
• 1999

We have fabricated $WO_3$ thick film gas sensor under various firing conditions in order to study gas sensing properties in terms of the variation of microstructure and non-stoichiometric structure of gas sensing layer. $WO_3$ paste mixed homogeneously with organic vehicle was coated by screen printing method on alumina substrate composed of Au electrode and $RuO_2$heater on each side. To change filing condition, sensing materials were fared at 600-$800^{\circ}C$ for 1 hour and refired at $700^{\circ}C$ for 1 hour in the mixtures of $_Ar/O2$gas. In the result of heat-treatment, $WO_3$ gas sensor fared at $700^{\circ}C$ showed best gas sensing properties of 210 gas sensitivity and 2 second response time and the best firing environment was 40-50% of $Ar/O_2$gas.

• Journal of Life Science
• /
• v.26 no.4
• /
• pp.460-467
• /
• 2016

A filamentous cyanobacterium, Limnothrix sp. KNUA012, was axenically isolated from a freshwater bloom sample in Lake Hapcheon, Hapcheon-gun, Gyeongsangnam-do, Korea. Its morphological and molecular characteristics led to identification of the isolate as a member of the genus Limnothrix. Maximal growth was attained when the culture was incubated at 25℃. Analysis of its lipid composition revealed that strain KNUA012 could autotrophically synthesize alkanes, such as pentadecane (C₁₅H₃₂) and heptadecane (C₁₇H₃₆), which can be directly used as fuel without requiring a transesterification step. Two genes involved in alkane biosynthesis－an acyl-acyl carrier protein reductase and an aldehyde decarbonylase－were present in this cyanobacterium. Some common algal biodiesel constituents－myristoleic acid (C_14:1), palmitic acid (C_16:0), and palmitoleic acid (C_16:1)－were produced by strain KNUA012 as its major fatty acids. A proximate analysis showed that the volatile matter content was 86.0% and an ultimate analysis indicated that the higher heating value was 19.8 MJ kg⁻¹. The isolate also autotrophically produced 21.4 mg g⁻¹ phycocyanin－a high-value antioxidant compound. Therefore, Limnothrix sp. KNUA012 appears to show promise for application in cost-effective production of microalga-based biofuels and biomass feedstock over crop plants.