• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.45.1-45.1
• /
• 2010

한국천문연구원과 일본 국립천문대는 공동으로 한일공동VLBI상관기(Korea-Japan VLBI Correlator, KJJVC)를 개발하였다. 이 상관기는 최대 16 관측국에 대하여 16 세트의 자기상관 및 120 세트의 상호상관을 계산할 수 있다. 각 관측국당 최대 8,192 Mbits/sec의 입력 데이터를 처리할 수 있으며, 8,192개의 주파수채널을 갖는 상관 스펙트럼을 약 25.4 밀리초~수초의 적분 시간으로 출력할 수 있는데, 최대 상관 출력 속도는 1.4GB/sec이다. 한편, 이 상관기는 한국우주전파관측망(KVN) 뿐만 아니라 동아시아VLBI관측망 및 우주공간VLBI관측망의 관측 데이터도 처리할 수 있도록 설계 제작되었으며, 최대 지연 추적 범위는 ${\pm}35,000km$이며, 보상 가능한 최대 기선 속도는 7.5km/sec이다. 현재 다른 VLBI관측망에서 사용하고 있는 타 상관기의 경우 지연은 2차 미분까지 보상하고, 프린지 위상은 3 단계로 보상하고 있는 것에 비하여, 한일공동VLBI상관기에서는 지연은 3차 미분까지 보상하여 지연 잔차를 최소화하고 프린지 위상은 16 단계로 세분하여 보상 수준의 정밀도를 최대화하였다. 이러한 지연 보상 및 프린지 멈춤 알고리즘을 상세히 소개하고 그 특성 및 장점을 보고한다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.2
• /
• pp.23-30
• /
• 2008

UHPC has high performance, high strength and excellent mechanical properties. Moreover UHPC(Ultra High Performance Cementitious Composite) has advantage to reduce cross section under the same load compared with other kinds of concrete. But silica fume which is imported from foreign country has a abundant portion in UHPC mixture in comparison with normal concrete. This is one of the main reason to raise the construction cost. Superior mechanical properties of UHPC due to the optimum filling composition can be changed by replacing the very fine ingredient. The purpose of this research is to grasp the characteristic of UHPC which silica fume and silica flour is replaced with limestone powder. This experiment can be divided into three classes according to the kinds of replacement. The compressive strength and flow of all types were measured and microstructure and hydration phenomena for comparing RPC were analyzed by SEM, XRD, NMR method. As a result, the replacement can be considered to be effective by for the decrease of the UHPC structure construction cost and improvement of the fresh UHPC.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.2
• /
• pp.114-121
• /
• 2017

The purpose of this study is to understand a compressive strength and propose a dry shrinkage strain equation being able to predict dry shrinkage of alkali-activated materials(AAM) mortar samples manufactured using fly-ash(FA) and ground granulated blast furnace slag(GGBFS). The main parameters investigated were the GGBFS replace ratios(30, 50, 70 and 100%) and sodium silicate modules(Ms[$SiO_2/Na_2O$] 1.0, 1.5 and 2.0). The compressive strength of AAM increased with increases GGBFS replace ratios or Ms contents. The dry shrinkage strain of AAM decreased with increases Ms contents. But, the dry shrinkage strain of AAM increased as the GGBFS replace ratio increases. Therefore, the GGBFS replace ratio seems to have very significant and important consequences for the mix design of the AAM mortar. The results indicated the R-square of single regression analysis based on each mix properties was the highest value; 0.7539~0.9786(average 0.9359). And the presumption equation of dry shrinkage strain with all variables(GGBFS, Ms and material age) has higher accuracy and its R-square was 0.8020 at initial curing temperature 23 degrees Celsius and 0.8018 at initial curuing temperature 70 degrees Celsius.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.541-555
• /
• 2020

The grouting method is used for reinforcing and waterproofing the soft ground, increasing the bearing capacity of structures damaged by lowering or subsidence due to rise and vibration, and for ordering. This study attempted to develop a blast furnace slag-based cementless grout material to increase the strength and hardening time of the grout material using reinforcing fibers. In this regard, in this study, it was used in combination with calcium hydroxide, which is an alkali stimulant of the three fine powders of blast furnace slag, and the content of calcium hydroxide was used by substituting 10, 20, and 30% of the fine powder of blast furnace slag. In addition, in order to compare the strength according to the presence or absence of reinforcing fibers, an experiment was performed by adding 0.5% of each fiber. As the content of carbon fibers and aramid fibers increased, the uniaxial compressive strength increased, and it was confirmed that the crosslinking action of the fibers in the grout material increased the uniaxial compressive strength. In addition, it was confirmed that the gel time sharply decreased as the content of the alkali stimulate increased.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.335-341
• /
• 1996

유한차분 감소를 이용한 감도해석 및 구조변경 프로그램을 개발하고 수치해석을 수행하여 다음과 같은 결론을 얻었다. 1) 유한요소 모델로부터 얻은 유한차분감도를 이용한 결과가 미분을 이용한 감도해석법의 결과에 비해 큰 차이없이 타당한 결과를 제시하여 주는 것을 확인하였다. 2) 복잡한 판구조물의 형상을 등가의 동특성을 갖는 보를 이용하여 모델링하고, 보의 단면치수를 설계변수로하여, 구조변경을 수행함으로써 효율적인 해석을 수행하였다. 3) 혀상이 복잡한 판 구조물의 형상 및 치수등 비선형적인 요소의 변경으로 인한 구조변경시 유한차분 감도 해석법을 이용한 구조변경이 좋은 결과를 나타내는 것을 확인하였고, 이로써 유한차분을 이용한 감도해석법이 형상최적화(shape optimization)에 적합한 방법임을 알 수 있었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.213-217
• /
• 2010

댐붕괴파 (dam-break flow)나 지진해일에 의해 발생하는 undular bore와 충격파 (shock) 현상을 동수압 및 분산효과를 고려하여 수치모의를 수행하였다. 완전비선형 Boussinesq-type equations 모형을 이용하여, 동수압 및 분산 효과를 고려하였다. 방정식은 4차 정확도의 유한체적법을 이용하여 해석하였고, 시간적으로도 4차정확도의 기법을 이용하여 고차미분항에 대한 수치분산을 억제하였다. 다양한 경우의 1차원과 2차원 공간에서의 수치모의를 수행하고 검증을 수행하였다. 그 결과, 완전비선형 Boussinesq-type equations 모형은 천수방정식 (shallow water equations) 기반의 모형에서 재현이 불가능한 undular bore 등을 재현 하는 등, 전반적으로 천수방정식 기반의 모형 보다 물리적으로도 타당하고 정량적으로도 실험결과와 잘 일치하는 경향을 보였다. 즉, 댐붕괴파나 지진해일 등에 의한 범람 모의에 있어 동수압과 분산 효과의 중요성이 공학적으로도 매우 중요한 고려사항 임이 나타났다.

• Korean Chemical Engineering Research
• /
• v.55 no.4
• /
• pp.548-555
• /
• 2017

This study investigated the influence of air staging on combustion and NOx emission in a tangential-firing boiler at a 560 MWe capacity. For air staging, the stoichiometric ratio (SR) for the burner zone was varied from 0.995 to 0.94 while the overall value was fixed at 1.2. The temperature and heat flux in the burner zone and upper furnace corresponded to the distribution of SR, while the total boiler efficiency remained similar. The NOx emission at the furnace exit was reduced by up to 20% when the SR in the burner zone decreased to 0.94. However, the amount of unburned carbon and slagging propensity was not noticeably influenced by the changes in the SR of the burner zone. Therefore, it was favorable to lower the SR of the burner zone for reduction of NOx emission.

• Resources Recycling
• /
• v.3 no.3
• /
• pp.32-49
• /
• 1994

Hydration process is one of the basic carbonation system. Limestone sludge produced in Pohang Iron & Steel Co., Ltd. We tested for identify of hydration characteristics. The result obtained in this study can be summarized as follows; 1. The classify of limestone sludge is type of ground calcium carbonate(-3mm+325mesh)and the major mineral of calcite, and further more high grade(CaO 51%), fine powder(15~22$\mu\textrm{m}$). 2. Limestone sludge mixed two process sludge, first one is washing process sludge and the other one is wet collect kiln dust. The composition rate is about 8:2. Wet collect kiln dust is major mineral of calcite, too. But the sludge is assumed to one by quick lime, slaked lime and unreacted natural limestone. So, the ideal process is dividing of the washing process sludge and wet collect kiln dust. 3. We manufactured of slaked lime from limestone sludge. To investigate the effect of hydration reactor, the experiments was done with various reactor type as magnetic stirrer, shaking incubator and ultrasonic vibration reactor, respectively. Generally, ultrasonic vibration reactor is excellent hydration for limestone sludge and produced very fine slaked lime powder with ideal distribution. 4. The optimum condition is 10% pulp density, when the manufacture of fine slaked lime powder by ultrasonic vibration reactor. And hydration times to compare the results of the study with ultrasonic vibration reactor of generalized most short time(5~10 min). 5. Finally, the dispersive characteristics of slaked lime powder measured 1~5 $\mu\textrm{m}$ from limestone sludge were compared with those of natural limestone ones(10~20$\mu\textrm{m}$), in order to check applicability of slaked lime with hydration process from limestone sludge.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.4
• /
• pp.427-436
• /
• 2006

The classical buckling theory assumes that prebuckling behavior is linear and that the effect of prebuckling deformations on buckling can be ignored. However, when the rise to span ratio decreases, prebuckling deformation cannot be ignored and the symetrical buckling strength can be smaler than the asymetrical buckling strength. Finally, arches can fail due to snap-through buckling. This paper investigates the non-linear behavior and strength of pin-ended parabolic shallow arches using the non-linear governing differential equation of shallow arches. These results were compared with the solution for the symmetrical buckling load of pin-ended parabolic shallow arches was suggested.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.2
• /
• pp.127-136
• /
• 2007

In this paper, the equations of the scaled boundary finite element method are derived for non-homogeneous half plane and analyzed numerically In the scaled boundary finite element method, partial differential equations are weaken in the circumferential direction by approximation scheme such as the finite element method, and the radial direction of equations remain in analytical form. The scaled boundary equations of non-homogeneous half plane, its elastic modulus varies as power function, are newly derived by the virtual work theory. It is shown that the governing equation of this problem is the Euler-Cauchy equation, therefore, the logarithm mode used in the half plane problem is not valid in this problem. Two numerical examples are analysed for the verification and the feasibility.