• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.950-955
• /
• 2004

Slip displacement is brought into focus to study the tube fretting wear that occurs on the contact by the springs. An oscillating tube was in contact with plate support springs. The contact condition was varied as normal force 5 N, and gaps of 0.1 and 0.2 mm in the experiment. The oscillation range of the tube was also varied as 0.2, 0.3, 0.4 and 0.7 mm. Formulas for predicting the slip displacement range were derived in terms of the vibration amplitudes measured during the tube oscillation. It was found that the slip displacement in transverse direction was much higher ($720{\sim}33000$ times) than that in axial one. This resulted in the severer wear on the contact suffered from transverse slip.

• Journal of KSNVE
• /
• v.8 no.2
• /
• pp.260-266
• /
• 1998

According to the conventional method of analysis for the seismic sliding of equipment submerged in a pool, in general, only the initial condition of fluid gap is used to estimate the hydrodynamic effect between the two structures throughout the seismic analysis. This is based on the assumption of small displacement relative to the fluid gap thickness during earthquakes. In a narrow fluid gap condition, however, this method may lead to a result of unconservative side. Through example seismic analyses for equipment submerged in a pool of a building, in this paper, it is studied when and how much the sliding response can be underestimated. And method of updating the hydrodynamic effect in each step of time integration is proposed to avoid excessive error in estimation of peak sliding response in such a case.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.67-72
• /
• 2004

Fundamentally, slip displacement should be known to solve the problem related to the fretting wear. For this, methods for measuring the slip displacement range in the contact surface of the tube and the supports were introduced and analyzed in this study. Also the increment of the slip displacement during a cycle was calculated using the revised formulas. As a result, the slip displacement newly evaluated was much higher ($7{\sim}50$ times) than that previously evaluated especially in the case of the gap existence. This enables to explain the severe wear found when there was a gap between the tube and the supports.

• Computational Structural Engineering
• /
• v.11 no.3
• /
• pp.165-172
• /
• 1998

본 연구에서는 종이 충격흡수의 효율적인 기하형상이 연구되었다. 일반적으로 충격흡수재는 골판지, 스폰지, 종이, 고무등으로 제작된다. 에너지 흡수거동에 대한 종이 충격 흡수재의 보강형태, 크기., 재료 특성에 대한 영향이 ABAQUS/Explicit5.5에 의한 유한요소 해석과 미끄럼 충격시험을 통해 연구되었다. 종이 충격 흡수재의 최대 변위는 충격속도에 따라 증가하며, 내부단수에 따라 감소하였다. 충격이력 특성은 내부단수가 7단일 때 5 msee까지 급속히 변형되며, 그 이후에는 영구변형으로 존재한다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.61-66
• /
• 1999

반복 응력 상태 아래서 알루미나 세라믹의 피로 표면손상 누적현상이 분석되었다. 연속 미끄럼 접촉 시에 발생하는 응력 상태를 재현하기 위해서 동시에 작용하는 수직-수평 반복 압축하중 기법이 사용되었다. 알루미나 구와 평판의 접촉면에서 알루미나 미세 결정의 피로 파손에 의한 마모 입자 형성 기구가 관찰되었고, 반복하중의 횟수와 수직-수평 하중비가 커질수록 마모량은 증가하였다. 반복 접촉하중에 의한 표면손상 누적이 접촉 수직 변위 측정으로 정량화 되었다. 두 접촉 구조물의 강성 (하중-변위 선도의 기울기) 변화가 두 재질의 탄성계수의 변화로 표현되었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.167-174
• /
• 2010

In this study, the optimal position for the backrest pivot of an office chair was investigated by evaluating its performance in terms of the lumbar support and sliding distance of the back from the backrest during tilting motions. The simulation was performed using a mathematical model, which included a human body and a chair. Forty-two backrest pivot points were selected on the sagittal plane around the hip joint of a sitting model. A motion analysis study was also performed using a prototype of an office chair (A-type) with a backrest pivot located on the hip joint of a normal Korean model and a typical office chair (B-type) with its pivot located under the seat. The simulation results showed that both the lordosis angle and the slide distance of the back were minimized when the backrest pivot was positioned close to the hip joint. The experimental results showed that the slide distance and gap between the sitter's lumbar and the backrest was smaller with the A-type than the B-type. Based on the simulation and experimental results, it can be concluded that the backrest can support the sitter's lumbar area more effectively as the pivot position for reclining approaches closer to the hip joint. In this position, the sitter can maintain a comfortable and healthy sitting posture. This paper presents the methods and guidelines for designing an office chair with ergonomic considerations.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.05a
• /
• pp.184-189
• /
• 2002

기계부품 및 구조물의 상호접촉면이 미소변위에 의해 상대운동을 할 때 접촉면에서는 마모가 발생하고 이러한 마모현상은 당해 구조물의 안전성을 심각하게 위협하는 결과를 초래하게 된다. 이러한 마모 현상에 대한 근래의 연구동향으로는 $Engel^{(1.2)}$ 이 충격(impact)에 의한 마모에 대해, 그리고 $Waterhouse^{(3)}$ 는 미끄럼(sliding) 마모에 대해 연구한 바 있다. 원자력발전소의 증기발생기(steam generator) 내에서 1차측의 세관(tube)과 2차측에 속하는 지지물(supporter) 또는 방진대(antivibration band) 사이에서 세관의 진동으로 인해 지지물과 충돌을 일으키고 충돌 횟수가 누적되면 세관의 마모로 이어져 결국 세관의 건전성은 침해받게 된다.(중략)

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.40-45
• /
• 2001

This paper proposes a methodology for the small-displacement-movement of a piston and develops a hybrid control algorithm for the precision position control of a pneumatic rodless cylinder. The pneumatic system uses the voltage-proportional solenoid valves to minimum valve switching since the on/off type valves are create diffculties for accurate position control and induce a lot of valve switching. For the accurate position control a methodology for the small-displacement-movement of the piston is developed and identified experimentally. The main consideration on the development of the hybrid control law is to eliminate a stick-slip phenomenon in the pneumatic control system. This paper addresses these critical issues and presents experimental results for the pneumatic control system.

• Journal of KSNVE
• /
• v.11 no.3
• /
• pp.461-470
• /
• 2001

A friction-type clutch system sometimes generates spick-slip vibration during engagement, which disturbs smooth start of a car and makes a passenger uncomfortable. In this study, the spick-slip vibration in four types of friction couples was investigated at two different engagement conditions respectively of which the amount of slip time and clutch travel was varied. Results are found as follows. First, the vibration increased at the condition of small engine torque and large torque fluctuations due to higher harmonics of engine speed. Second, the friction couple without a pre-damper has advantages of reducing the vibration. This study also suggested an evaluation method of vehicle vibration in the view point of human perception by using the frequency weighting of ISO2631-1.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.41-49
• /
• 2003

Tube oscillation behaviour is experimentally investigated for the study on the fuel rod fretting that is caused by the flow-induced vibration in nuclear reactor. The experiment was conducted in all at room temperature. The specimen of tube assembly was supported by plate springs which simulated the spacer grids and fuel rods of a fuel assembly. To investigate the influence of contact condition between the grids and rods, normal load of 10 and 5 N, gaps of 0.1 and 0.3 mm were applied. The range of the oscillation at the center of the fuel rod specimen was varied as 0.2, 0.3 and 0.4 mm to simulate the fuel rod vibration due to flow. Displacements near the contact were measured with four displacement sensors during the tube oscillation. As results, the shape of oscillation (phase) varied depending on the contact condition. The oscillation displacement increased considerably from the contact to gap condition. The displacement increased further as the gap size increased. It is regarded that the spring shape influences the tube oscillation behaviour. Simple calculation showed that the slip displacement was very small. Therefore, cumulative damage concept is necessary for the fuel rod wear. The mechanism of plowing is thought required to explain the severe wear in the case of gap existence.