• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.4
• /
• pp.261-270
• /
• 1996

Boriding is one of the chemical methods to achieve the case hardening of steel as well as nitriding or carburizing. The surface layer of the borided steel shows higher hardness and exhibits better resistance to corrosion or fatigue than the nitrided or carburized steel. The great majority of previous studies were confined to mild steel or some alloy steel. To enlarge the application, ductile cast iron (DCI) as a material for boriding has been tried in this study. Thus, sliding wear test has conducted using a pin-on-disc machine to compare between borided DCI and mild steel in fluidized bed furnace. The results show that the wear resistance of borided DCI is improved. Especially it is more efficient in the case of occurence of the mechanical wear.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.74-79
• /
• 2014

This article aims at investigating the effect of applied load and sliding speed on wear behavior of thermally spraryed STS316 coating. STS316 coatings were fabricated by flame spray process according to optimal parameters on steel substrates. Dry sliding wear tests were performed on STS316 coating using four different applied load as 10, 15, 20 and 25 N and four different sliding speed as 15, 30, 45 and 60 rpm. Wear behavior on worn surface was investigated using scanning electron microscope(SEM) and energy disperive X-ray spectroscopy(EDS). The dominant wear mechanism of STS316 coating under low applied load and sliding speed was oxidation on worn surface. However, under high applied load and sliding speed the principal wear mechanism was abrasion on oxidation film and damage of oxidation film.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.48-59
• /
• 1989

최근 터어보 샤프트, 터어보 팬, 터어보 쳇트 엔진, 가스 터어빈, 공작기계의 주축, 그리고 섬유기계 섬유봉등의 회전기계류 설계에서 단위 무게당 출력의 비율을 높이기 위해서 회전속도의 고속화가 요구되고 있다. 이러한 경우 회전축계의 진동특성에 크게 영향을 미치는 감쇠특성을 부각시키기 위하여 베어링의 외부에 스퀴즈-필름 댐퍼 (Squeeze-film Damper)를 부가하고 회전축계를 유연하게 지지하여 줌으로써 진동문제를 간단히 해결하며 회전속도의 고속화를 가능하게 할 수 있다. 적합하게 설계된 스퀴즈-필름 댐퍼의 잇점은 다음과 같다. (a) 회전축의 위험속도를 작은 공진쪽으로서 통과하는 것이 가능. (b) 베어링과 지지구조물에 전달되는 하중이 감소 (c) 장기간 사용중, 마모 및 브레이드 파손에 의해 진폭이 증가된 불평형 강제진동에서도 안정된 운전이 가능 (d) 미끄럼 저어널 베어링에 지지된 회전축계의 고속회전에서 불안정한 자려진동이 나타나는 안정 한계속도를 높히는 것이 가능

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.144-148
• /
• 1999

The relationship between oxidation and sliding wear behavior of Fe-28 at%. Al alloys with B2 ordered structure has been investigated. Sliding wear tests of the alloys have been carried out under various environmental conditions using a pin-on-disk wear tester. The wear rate of the ordered alloys in an oxygen atmoshpere was found to be much lower than in an oxygen atmosphere showed that Fe2O oxides formed on the wearing surface. The oxide layer prevented direct contact of the two mating materials and therefore improved wear resistance of the Fe-Al intermetallic alloy. It was found that the surface Al2O3 oxide layer which provides good oxidation resistance and improved mechanical properties broke down easily and didnot function properly as an oxidation barrier.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.19-24
• /
• 1999

Understanding of wear mode and prediction of wear rate of parts in sliding contact are very important in field of meterial design relating with wear resistant. This paper has been undertaken to analyze the possibility of elucidation of wear mode and prediction of wear rate for annealed steel in sliding contact using the X-ray diffraction. The sliding wear test with various velocities using pin-on-disc machine and the X-ray diffraction test on the worn surface have been carried out. The results have been shown that the magnitude of residual stress and half-value breadth on the worn surface have a good correlation with wear mode. The difference between before and after test of half-value breadth on worn surface has been shown to be exponential relation with wear rate in the same wear mode.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.135-140
• /
• 2001

In metal cutting at the tool-chip interface, friction generates considerable amount of heat. Thus, tile .knowledge of wear properties or the cutting tool material in high temperature has been known as one of tile important factors in need of clarification. The authors presented the wear properties of 5%V-5%Co-1%Nb high speed steel, fabricated by powder metallurgy, in room temperature in a previous article. The objective of this paper is to clarify tile effects of temperature ell its wear properties. Wear tests in sliding conditions under various temperatures have been conducted. The results indicate that tile wear properties of tile tool material in high temperature as well as in room temperature are excellent. It may be deduced that the oxide layer formed on the vol-n surface at high temperature is stable enough to prevent wear due to tile high temperature strength of its matrix.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.35-40
• /
• 1996

Friction and wear behavior of MoS$_{2}$ bonded films were evaluated at a Block-on-Ring typed tribo-tester, and their properties were compared with those of Falex tester in terms of the wear life of the films. Test results showed that friction and wear properties were significantly affected by the test methods of different contact configuration, and the wear life at a Block-on-Ring type tribo-tester was mostly governed by the resin binder. To obtain long wear life of the films, various combinations of solid-resin-content ratio and chemical resin modification were attempted and evaluated. Adhesion properties of resin binders were also measured and compared by using a scratch tester.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.80-88
• /
• 2000

The plasma spray technics has known as one of the surface modification methods to improve the mechenical properties or the functional charactristics of materials. This paper has been aimed to investigate the effects of plasma sprayed conditions, such as spray distance and arc power level, on sliding wear properties of plasma sprayed $Al_2$O$_3$-40%TiO$_2$coating layer. The sliding wear test using pin-on-disc type wear machine, has been conducted in several sliding speed for coating layer sparyed under different conditions. The result of this paper is that the wear resistance of plasma sprayed $Al_2$O$_3$-40%TiO$_2$coating layer is fluctuated with tile spray distance and the arc power level. The wear resiatance could be improved with decreasing the spray distance and with increasing the arc power level.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.194-200
• /
• 2000

In order to evaluate the effect of Nb on wear properties of high speed steel(HSS) by powder metallurgy, niobium-alloyed HSS have been prepared by adding 0%, 1%, 3% and 5%Nb to HSS of 6%W-5%Mo-4 %Cr-5%V-5%Co. Sliding wear tests were conducted at various sliding speed conditions under the constant pressure using a pin-on-disc type machine. The results of this study show that the wear resistance of HSS by powder metallurgy was increased by the addition of Nb within the range of sliding speed used in this experimental study. However, the amount of Nb did not improve the wear resistance. It may be due to the thermal stability of carbide and high temperature properties of the matrix containing Nb comparing to that without Nb.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.267-273
• /
• 2009

Three types of structural intermetallic compounds, $Ni_3Al$, NiAl and TiAl, having each single phase structure without pores were produced by arc-melting process. Their sliding wear properties were investigated against a hardened tool steel. It was shown that the wear of the intermetallic compounds was hardly occurred against the hardened tool steel. TiAl compound showed the best wear resistance among them. In this case, wear was preferentially occurred on the surface of the hardened tool steel of the mating material which has higher hardness. It could be found that the wear mode on intermetallics without pores by arc-melting process was different from that on its porous layer coated on steel by combustion synthesis.