• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.2
• /
• pp.117-131
• /
• 2006

A coupled T-H-M(Thermo-Hydro-Mechanical) analysis was carried out for KENTEX (KAERI Engineering-scale T-H-M Experiment for Engineered Barrier System), which is a facility for validating the coupled T-H-M behavior in the engineered barrier system of the Korean reference HLW(high-level waste) disposal system. The changes of temperature, water saturation, and stress were estimated based on the coupled T-H-M analysis, and the influence of the types of mechanical constitutive material laws was investigated by using elastic model, poroelastic model, and poroelastic-plastic model. The analysis was done using ABAQUS, which is a commercial finite element code for general purposes. From the analysis, it was observed that the temperature in the bentonite increased sharply for a couple of days after heating the heater and then slowly increased to a constant value. The temperatures at all locations were nearly at a steady state after about 37.5 days. In the steady state, the temperature was maintained at $90^{\circ}C$ at the interface between the heater and the bentonite and at about $70^{\circ}C$ at the interface between the bentonite and the confining cylinder. The variation of the water saturation with time in bentonite was almost same independent of the material laws used in the coupled T-H-M processes. By comparing the saturation change of T-H-M and that of H-M(Hydro-Mechanical) processes using elastic and poroelastic material mod31 respectively, it was found that the degree of saturation near the heater from T-H-M calculation was higher than that from the coupled H-M calculation mainly because of the thermal flux, which seemed to speed up the saturation. The stresses in three cases with different material laws were increased with time. By comparing the stress change in H-M calculation using poroelasetic and poroelasetic-plastic model, it was possible to conclude that the influence of saturation on the stress change is higher than the influence of temperature. It is, therefore, recommended to use a material law, which can model the elastic-plastic behavior of buffer, since the coupled T-H-M processes in buffer is affected by the variation of void ratio, thermal expansion, as well as swelling pressure.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.111-117
• /
• 1999

섬유강화 복합재료의 섬유와 수지까지 세부적으로 모델링이 가능한 Direct Numerical Simulation을 통해서 Boron/Aluminum 섬유강화 복합재료의 탄성계수들을 구해 보았다. 수치실험에서는 복합재료를 직교이방성 물질로 가정하였고, 특정 체적에 대한 평균치를 이용해서 물성치를 구하였으며, 혼합법칙에 의해서 구한 값 및 대표체적요소(Representative Volume Element)를 사용해서 구한 값들과 비교하였다. 혼합법칙의 경우, 섬유방향 인장계수(E₁)을 제외한 나머지 물성치들에 대해서는 상당한 차이를 나타내며, 이는 혼합법칙 유도과정에서 가정한 기본가정들이 적절하지 않기 때문이라는 것을 수치실험(Numerical Experiment)을 통해 알 수 있었다.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.236-240
• /
• 2017

다양한 분야에서 복합재료의 중요성이 강조되면서 각각의 재료 특성에 따른 물성을 미시역학적으로 구하는 것에 대한 다양한 방법이 제시되고 있다. 본 논문에서는 5개의 혼합 법칙을 선정하여 전산구조해석을 통한 유한요소해석을 비교 검증한다. 그 과정에서 산출된 결과를 통하여 복합재료의 탄성거동의 오차가 1% 미만인 것을 확인하였고, 프로그램의 해석이 적절하다는 것을 검증하였다. 또한 프로그램과 가장 유사한 혼합 법칙이 무엇인지 확인하고, 체적 비에 따른 오차를 비교하여 가장 적합한 체적 비를 선정하였다.

• Clean Technology
• /
• v.15 no.3
• /
• pp.172-179
• /
• 2009

The thermoplastic polyurethane waste (TPU-S) with good tensile properties, hardness, NBS abrasion resistance, specific gravity and low wet coefficient of kinetic friction was melt-blended with ethylene propylene diene monomer rubber (EPDM) with high wet slip resistance and low mechanical properties to form EPDM/TPU-S blend films, and their composition-property relationship was investigated to find the optimum composition for shoe outsole material. The properties except the wet slip resistance increased with increasing TPU-S contents in the blend. All the properties except elongation at break, specific gravity and the wet coefficient of kinetic friction in the range of $0{\sim}65\;wt%$ of TPU-S did not attain the values predicted by the simple additive rule. The optimum weight ratio of EPDM/TPU-S for the application to the typical shoe outsole material was found to be 30/70.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.23-36
• /
• 1990

The various composite materials have been developed with the development of high strength material and the increasement of composite material usage. Therefore many researchers have studied about the stress analysis and the fracture mechanics for composite materials through the experiment or the theory. Among the experimental methods, the photoelastic experiments have been used for the stress analysis of the isotropic structures or the anisotropic structures. To analyze the stresses in the orthotropic material with photoelastic experiment, the basic physical properties ( $E_{L}$, $E_{T}$, $G_{LT}$ , .nu.$_{LT}$ ) and the basic stress fringe values ( $f_{L}$, $f_{T}$, $f_{LT}$ )are needed, therefore the relationships between the basic physical properties and the stress fringe values were derived in this paper. When the stress fringe value is very large, it was assured by the experiment that the relationships are established both in the room temperature and in the high temperature (T = 130.deg. C). Therefore the basic physical properties can be obtained from the relationships by measuring stress fringe values instead of measuring the basic physical properties.rties.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.663-670
• /
• 2020

A study on mechanical property characterization and modeling technique was carried out to approximate the behaviour of structures with 2.5D C/SiC material. Several tensile tests were performed to analyze the behaviour characteristics of the 2.5D C/SiC material and elastic property was characterized by applying a mathematical homogenization and a modified rule of mixture. SiC matrix representing the elasto-plastic behavior approximates as a bilinear function. Then the equivalent yield strength and equivalent plastic stiffness were calculated by minimizing errors in experiment and approximation. RVE(Representative Volume Element)was defined from the fiber and matrix configuration of 2.5D C/SiC and a process of calculating the effective stiffness matrix by applying the modified rule of mixture to RVE was implemented in the ABAQUS User-defined subroutine. Finite element analysis was performed by applying the mechanical properties of fiber and matrix calculated based on the proposed process, and the results were in good agreement with the experimental results.

• Composites Research
• /
• v.33 no.2
• /
• pp.81-89
• /
• 2020

In this review paper, we introduce recent research studied effective physical properties of the reinforced composite using mean-field homogenization. We address homogenization for effective stiffness and expand it to effective thermal/electrical conductivity and dielectric constant. Multiphysics problems like piezoelectricity and thermoelectricity are considered by simplifying the constitutive equation into the linear equations like Hooke's law. We present a generalized theoretical formula for predicting effective physical properties of composite and validation by against finite element analysis.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.1
• /
• pp.13-20
• /
• 2008

Graded layers in which two different constituent particles are mixed are inserted into functionally graded material such that the volume fractions of constituent particles vary continuously and functionally over the entire material domain. The material properties of this dual-phase graded region, which is essential for the numerical analysis of the thermo-mechanical behavior of FGM, have been predicted by traditional homogenization methods. But, these methods are limited to predict the global equivalent material properties of FGMs because the detailed geometry information such as the particel shape and the dispersion structure is not considered. In this context, this study intends to investigate the characteristics of these homogenization methods through the finite element analysis utilizing the discrete micromechanics models of the graded layer, for various volume fractions and external loading conditions.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.22-28
• /
• 2009

열역학 제 2법칙의 관점의 열역학적 가용에너지인 엑서지 해석법을 적용하여 가솔린, 메탄올, M90 연료를 사용한 전기점화 기관의 성능해석을 수행하였다. 열역학적 사이클 해석을 위하여 사이클을 구성하는 각 과정은 열역학적 모델로 단순화하였고, 크랭크 각도에 따른 실린더의 압력과 작동유체를 구성하는 연료, 공기 및 연소생성물의 열역학적 물성 값들을 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였다. 실험데이터는 단기통 전기점화기관을 가솔린, 메탄올과 M90(메탄을 90%+부탄 10%의 혼합연료)을 연료로 WOT(Wide Open Throttle), MBT(Minimum advanced spark timing for Best Torque), 2500rpm 조건으로 운전하여 측정하였다. 계산에 이용한 자료는 실험으로 측정한 크랭크 각도에 따른 연소실의 압력, 흡입공기와 연료유량, 흡입공기 온도, 냉각수 온도와 배출가스 온도 등이다. 이를 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였으며 각 과정에서의 손실 일은 연소과정에서 가장 크며 팽창과정, 배출과정, 압축과정 및 흡입과정 순으로 크게 나타났다.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1587-1589
• /
• 1999

초고압 XLPE(가교 폴리에틸렌) 절연 케이블의 절연사고를 방지하기 위해서는 여러열화 조건하에서 절연체의 수명을 예측하는 것과 아울러 절연체(XLPE)의 성능향상을 모색하는 것이 바람직하다. 이러한 노력의 일환으로 절연재료의 열화현상을 화학반응의 법칙으로 가정한 Arhenius 모델과 같은 열화이론이 확립되어지고 있다 하지만, 실제 케이블을 만드는 과정에서 절연체의 성형 조건에 따른 절연 성능 평가와 관련된 연구는 그렇게 많지 않다. 본 연구에서는 XLPE의 성형 조건(가교, 건조, 냉각)에 따른 화학적 물성의 변화와 절연성능 사이의 상관관계를 알아보기 위해 LDPE에 가교제(DCP)를 첨가한 컴파운드를 이용해 만든 몰드 시편의 물성을 DSC, 가교도 분석 및 전기 트리 개시 전압을 측정해 살펴보았다. 그 결과 가교나 건조 조건에 비해 냉각 조건에 따른 가교 폴리에틸렌의 결정화도가 트리 개시전압에 보다 큰 영향을 미침을 알 수 있었다.