• Annual Conference of KIPS
• /
• 2011.04a
• /
• pp.681-684
• /
• 2011

최근 IEEE 802.11 WLAN(Wireless Local Area Network)에서 실시간 멀티미디어 서비스가 증가하고 있다. WLAN 의 패킷 전송방식은 Unicast 또는 Broadcast 방식이 있다. Unicast 방식은 재전송을 포함하여 유실율이 적으나 사용자가 증가할수록 AP 에서 필요한 무선 자원의 크기가 증가한다. 무선 자원의 크기가 증가하면 AP 부하가 증가하여 서비스 수용에 한계가 있다. Broadcast 방식은 사용자 수에 상관 없이 무선 자원의 크기가 일정하나, 패킷 유실율이 높다. 본 논문에서는 이러한 문제점을 해결하기 위해 Broadcast 와 FEC(Forward Error Correction) Erasure Code 기반 기술을 적용하는 것을 제안한다. 방송 패킷을 이용 AP 의 부하를 줄이고, Reed Solomon Erasure Code 를 적용하여 패킷 유실 복구율을 높인다. 이러한 방법을 통하여 다수의 사용자에게 안정적인 실시간 멀티미디어 방송 서비스를 제공 할 수 있다. 제안한 방법을 검증하기 위해 Android Platform 에서 FEC 적용 유무에 따른 수신율을 측정하였다. 그 결과 유실율 30%미만인 Broadcast 환경에서 96.4% 이상의 수신율을 보였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.25-27
• /
• 2022

Recently, with the development of the 4th industry, environmental issues such as air pollution have become serious, and in particular, a lot of air pollutants are generated in industrial sites. There are various types of air pollutants, and among them, carbon monoxide is essential for fires occurring in industrial sites, so it should be possible to monitor in real time. In addition, there is a need for a remote monitoring system that can measure various environmental factors other than air pollutants in real time. In this paper, we propose a monitoring system using wireless communication to remotely measure the industrial environment. The proposed monitoring system collects data to the Arduino of the transmitter by using a carbon monoxide sensor, a combustible gas sensor, a temperature and humidity sensor, and a flame sensor, and then transmits it to the receiver using ZigBee. The transmitted data is stored in the database of the receiver Raspberry Pi, and the stored data can be monitored in real time through the monitoring system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8A
• /
• pp.889-897
• /
• 2004

In this Paper, we propose the algorithm to provide stable communication in OFDM system under the highly interfered environment by the same/different systems which use same bandwidth or other jamming signal, i.e., radar signal. The proposed Adaptive Subcarrier Assignment(ASA) method first estimates the received power of each subcarrier in the block or fin or OFDM receiver. Then we estimate the threshold level which is the average power of the transmitted OFDM signal with AWGN. The highly interfered subcarriers, which are greater powers than the specified threshold level, are rejected in the next transmission and the only non-interfered subcarriers are selected as the next transmission. This algorithm provides stable communication in any OFDM systems without changing the physical layer under the highly interfered communication environment. We estimated the status of the subcarriers based on the bandwidth and power of the jamming signal and showed the performance of the proposed algorithm by the simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.485-489
• /
• 2000

본 논문에서는 단일 PLL을 사용하여 400MHz 대역의 트랜시버를 구현하였다. 일반적인 트랜시버의 경우, 송수신부에 각각 한 개의 PLL과 수신부에 2단의 믹서를 사용하여 구현되어진다. 이러한 구성은 트랜시버의 가격과, 부피에 상당히 큰 영향을 미친다. 본 논문에서는 기존의 방식을 탈피하여 단일 PLL방식의 데이터 전송용 특정 소출력 무선기기의 송, 수신단의 회로설계, 제작 및 특성측정을 하였다. 설계된 트랜시버의 주파수 대역은 424.7-424.95MHz이고, Low Side Injection방식을 사용하여 450KHz의 If 주파수로 변환(Conversion)하였고, 반이중(Semi duplex Communication) 통신방식, PLL Synthesized, 21 Channel, 12.5KHz Channel BandwidttL FSK Modulation / Demodulation 방식을 사용하였다.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.2
• /
• pp.54-61
• /
• 1999

This paper describes the design of a 4-Mbps wireless infrared data transceiver chip. The receiver consits of the analog front-end, clock recovery and frame generator, and demodulator. The transmitter consists of the demodulator and LED driver. The versatile analog front- end consisting of multiple amplifiers makes it possible for the chip to be applied to various infrared environments by compensating DC and offset signal components. A 4PPM (pulse position modulation) scheme is used for data transfer in order to meet the IrDA standards. The chip was fabricated in a $0.8-{\mu}m$ 2-poly, 2-metal CMOS technology and dissipates 122mW for ${\pm}2.5V$ supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.922-929
• /
• 2005

This paper proposes an adaptive pilot beacon equipment for mobile communication systems based on direct spread spectrum technology which generates the pilot channel for handoff between base stations by using the information acquired from the downstream wireless signal regarding the overhead channel information. Such an adaptive pilot beacon equipment will enable low power operation since among the wireless signals, only the pilot channel will be generated and transmitted. The pilot channel in the downstream link of the CDMA receiver is used to acquire time and frequency synchronization and this is used to calibrate the offset for the beacon, which implies that time synchronization using GPS is not required and any location where forward receive signal can be received can be used as the installation site. The downstream link pilot signal searching within the CDMA receiver is performed by FPGA and DSP. The FPGA is used to perform the initial synchronization for the pilot searcher and DSP is used to perform the offset correction between beacon clock and base station clock. The CDMA transmitter the adaptive pilot beacon equipment will use the timing offset information in the pilot channel acquired from the CDMA receiver and generate the downstream link pilot signal synchronized to the base station. The intermediate frequency signal is passed through the FIR filter and subsequently upconverted and amplified before being radiated through the antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.6
• /
• pp.679-689
• /
• 2014

In this paper, an analysis of the effect of time-variant reflected impedance and its detection method on wireless power transfer(WPT) systems are presented. The reflected resistance at WPT systems is very important parameter as it indicates how well matched antenna is and will exhibit high efficiency. Proposed detection method is based on transmitter current variation analysis with respect to frequency sweep. Using the proposed design method, a wireless power transfer system operating at the frequency of 125 kHz, is design and detect reflected impedance variation. The proposed design method provides good agreements between measured and simulated results. Therefore, The proposed detecting method provides a nonintrusive method to detect harmful object in WPT system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.10
• /
• pp.935-940
• /
• 2016

Recently, wireless power transmission system is gradually extended to technology in various fields such as lighting field, electric vehicles and smartphones wireless charging system. The largest of the two elements for high transmission efficiency of the wireless power transmission system are resonant coils and power amplifiers. In this paper, in order to build a high efficient wireless power transmission system, we introduce the resonance coil manufacturing method and high efficiency power amplifier design method that operates at 6.78MHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2431-2436
• /
• 2012

This paper is implemented simple visible light communication system by combining the communications through LED lighting. It uses a variable PD sensor to the receiver and 1~12 the LED light-emitting device to the transmitter to realize LED visible light communication. Initial distance value of the developed transmission and receiver is more than 0~1.5m for LED visible light communication, the overall system transmission rate is organized with thousands kbps variability visible light media transmission system. It was measured the performance experiment during lens wearing or not wearing in order to increase the overall efficiency of the LED module, configures the LED and PD to existing PC module for the performance analysis of the implemented research, experiments the maximum communication distance of the transmitter/receiver according to LED count and the transmission rate, check about application methods and the possibility.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.338-347
• /
• 2017

This paper describes the design and fabrication of a high power amplifier which is a component of TDL(Tactical Data Link) aircraft terminal. We applied high-speed frequency hopping technology, cognitive radio technology, and receive filter bank technology to efficiently use limited frequency resources with radar and other communication equipment using the same frequency band. The high-power amplifier is physically composed of a transmitter, a receiver, a mechanical part, and a cable assembly, and is designed to meet temperature characteristics and electrical characteristics such as maximum transmission distance and reception sensitivity. Modeling and simulator were used to satisfy the requirement of high power amplifier. The transmit power and the noise figure were measured at 50.02dBm and 2.682dB, respectively. It was confirmed that all the required specifications were satisfied in the electrical characteristics test and the environmental characteristic test.