• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.613-622
• /
• 2013

In this paper, an inductive clamping class-E power amplifier has been tested for wireless power transmission at ISM band, 13.56 MHz. The implemented power amplifier is designed to operate stably without destroying power transistor in wireless power transmission system which basically keeps not to align between a transmitting antenna and a receiving antenna. The power amplifier is also designed to enhance harmonic filtering characteristic. The amplifier was tested with a DC supply voltage of 28 V and input power of 25 dBm at 13.56 MHz. The test results show the output power level of 43 dBm, the difference power level between fundamental frequency and second harmonic frequency of more than 55 dBc, the dc current consumption of 830 mA, and the high power-added efficiency of 85 %. Finally, the implemented power amplifier operated normally with 830 mA DC current consumption from 28 V source when the two antennas were aligned, and the power transmission was successful. But when the two antennas were not aligned, its DC current consumption automatically decreased down to 420 mA to protect the switching transistor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.10C
• /
• pp.967-983
• /
• 2003

In wireless spread-spectrum communication systems utilizing PN (pseudo noise) sequences, a variety of noise sources from the channel affect the data reception performance. Among them, in this paper we are concerned with the narrowband interference that may arise from the use of the spectral bands overlapped by the existing narrowband users or the intentional jammers as in military communication. The effect of this interference can be reduced to some extent at the receiver with the PN demodulation by processing gain. It is known, however, that when the interferers are strong, the reduction cannot be sufficient and thereby requiring the extra use of narrowband interference cancellers (NIC's) at the receivers. A class of adaptive NIC's are studied here based on different two cost functions. One is the chip mean-squared error (MSE) computed prior to the PN demodulation and used in the conventional cancellers. Since thses conventional cancellers should be operated at the chip rate, the computational requirements are enormous. The other is the symbol MSE computed after the PN demodulation in which case the weights of the NIC's can be updated at a lot lower symbol rate. To compare the performance of these NIC's, we derive a common measure of performance, i.e., the symbol MSE after the PN demodulation. The analytical results are verified by computer simulation. As a result, it is shown that the cancellation capability of the symbol-rate NIC's are similar or better than the conventional one while the computational complexity can be reduced a lot.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.156-167
• /
• 2021

In this paper, we propose a digital transceiver unit design for in-building of 5G optical repeaters that extends the coverage of 5G mobile communication network services and connects to a stable wireless network in a building. The digital transceiver unit for driving the proposed 5G optical repeater is composed of 4 blocks: a signal processing unit, an RF transceiver unit, an optical input/output unit, and a clock generation unit. The signal processing unit plays an important role, such as a combination of a basic operation of the CPRI interface, a 4-channel antenna signal, and response to external control commands. It also transmits and receives high-quality IQ data through the JESD204B interface. CFR and DPD blocks operate to protect the power amplifier. The RF transmitter/receiver converts the RF signal received from the antenna to AD, is transmitted to the signal processing unit through the JESD204B interface, and DA converts the digital signal transmitted from the signal processing unit to the JESD204B interface and transmits the RF signal to the antenna. The optical input/output unit converts an electric signal into an optical signal and transmits it, and converts the optical signal into an electric signal and receives it. The clock generator suppresses jitter of the synchronous clock supplied from the CPRI interface of the optical input/output unit, and supplies a stable synchronous clock to the signal processing unit and the RF transceiver. Before CPRI connection, a local clock is supplied to operate in a CPRI connection ready state. XCZU9CG-2FFVC900I of Xilinx's MPSoC series was used to evaluate the accuracy of the digital transceiver unit for driving the 5G optical repeater proposed in this paper, and Vivado 2018.3 was used as the design tool. The 5G optical repeater digital transceiver unit proposed in this paper converts the 5G RF signal input to the ADC into digital and transmits it to the JIG through CPRI and outputs the downlink data signal received from the JIG through the CPRI to the DAC. And evaluated the performance. The experimental results showed that flatness, Return Loss, Channel Power, ACLR, EVM, Frequency Error, etc. exceeded the target set value.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.12
• /
• pp.1201-1208
• /
• 2016

Radio Frequency Identification (RFID) technology has a significant attraction throughout various industry sites, along with the development of wireless communication technologies. The typical applications of RFID include medical, logistics, and distribution, and, specially, it is effectively applied to non-contact environments, because it employs radio waves. Although, recently, construction cases of the RFID management systems for the inventory management of the construction materials have been increased, the related researches and experiments for the reused materials are not actively performed. In this paper, we propose the RFID system with the localization function for effectively managing the reuse of the construction materials, adding to the conventional inventory management system. The proposed system consists of a RFID reader unit and a receiver unit, and the location information of the material with the attached RFID tag is obtained by estimating the position of a RFID reader. The distance value for estimating the reader position is calculated using the Received Signal Strength Indicator (RSSI) value of Zigbee, and the performance evaluation of the proposed system is performed in the indoor space of $5m{\times}5m$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.8C
• /
• pp.806-813
• /
• 2009

This paper presents a modem chip design for high-speed wireless communications. Among the high-speed communication technologies, we design the UWB (Ultra-Wideband) modem SoC (System-on-Chip) Chip based on a MB-OFDM scheme which uses wide frequency band and gives low frequency interference to other communication services. The baseband system of the modem SoC chip is designed according to the standard document published by WiMedia. The SoC chip consists of FFT/IFFT (Fast Fourier Transform/Inverse Fast Fourier Transform), transmitter, receiver, symbol synchronizer, frequency offset estimator, Viterbi decoder, and other receiving parts. The chip is designed using 90nm CMOS (Complementary Metal-Oxide-Semiconductor) procedure. The chip size is about 5mm x 5mm and was fab-out in July 20th, 2009.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.3
• /
• pp.247-255
• /
• 1995

This paper describes a personal computer(PC) based color fish finder to improve some problem of the commercial one. The commercial fish finder has no function of the echo data logging and replaying. The authors developed two types of the PC based color fish finder. One is a master type composed of a PC, a digital input-output board, and analog to digital converting (A/D) board and an ultrasonic transceiver unit, the other is a slave type composed of a PC and an A/D board. To test the performances of the master type experiments were carried out in air and in a water tank. It is found that the designed master type fish finder displays very well an eight-colored echogram by one dot resolution to the left side of the PC monitor. Also, the depth of echo signal was corresponds very well to the range from the transducer to a target. The sampling interval of echo signal is about 0.1m and the time of A/D conversion is 30 $\mu$sec. On the other hand, to test the performances of the slave type a raw data of echo signals from a data logger was supplied directly or via RF transceivers to the slave type one. From this experiment, it is confirmed the slave type is useful to replay the echo signal from the data logger or a telesounder.

• Proceedings of the Korean Information Science Society Conference
• /
• 2006.10d
• /
• pp.370-374
• /
• 2006

Ad-hoc 환경의 응용은 재난구조나 회의실 또는 강의실에서의 정보 교환과 같은 그룹 통에서 이용된다. Ad-hoc 환경은 무선 채널을 이용하므로 상대적인 낮은 대역폭과 높은 오류 발생률을 가지게 된다. 따라서 Ad-hoc 네트워크에서는 신뢰적인 전송이 요구된다. 이동 노드는 상대적으로 낮은 성능과 에너지의 제한으로 인해 유선 환경과 같은 신뢰적인 전송 기법을 Ad-hoc 환경에 적용하기에는 문제가 발생한다. Ad-hoc 환경의 무선 채널이 가지는 보안적인 취약성과 높은 에러율을 극복하는 신뢰적인 그룹 키 전송을 위한 재전송 기법을 제안한다. 신뢰적인 트리 형성하기 위해 n차 트리 구조를 이용한다. 손실 감지를 위한 ACK 메시지를 이용하고 손실 복구를 위한 재전송 기법에 대해 연구를 한다. 제안한 신뢰적인 그룹 키 전송을 위한 재전송 기법은 트리의 깊이의 차수가 루트 관리 노드, 서브 관리 노드와 로컬 멤버 노드로 구성되기 때문에 손실 감지와 손실 복구에 대한 연산의 오버헤드가 적다. 루트 관리 노드는 멤버 노드로부터 받은 개인키 정보를 이용하여 그룹 키를 생성하고 그룹 키 부분 정보를 서브 관리 노드에게 전송하고 서브 관리 노드에 대한 신뢰성을 책임진다. 서브 관리 노드는 루트 관리 노드로부터 받은 그룹 키 부분 정보를 로컬 멤버 노드에게 전송하고 로컬 멤버 노드에 대한 신뢰성을 책임진다. 루트 관리 노드와 서브 관리 노드를 관리 노드라 한다. 관리 노드가 신뢰적인 전송을 위해 관리하는 멤버 노드는 전체 그룹에 독립적으로 유지 가능하므로 확장성 및 효율성이 좋다. 관리 노드는 동적인 그룹에 따른 타이머를 설정함으로써 손실 감지에 대한 시간을 줄임으로써 효율적인 손실 감지 및 손실 복구를 한다. 임계값 설정으로 인한 중복 수신에 대한 오버헤드를 줄일 수 있다.신뢰성을 향상 시킬 수 있는 Load Balancing System을 제안한다.할 때 가장 효과적인 라우팅 프로토콜이라고 할 수 있다.iRNA 상의 의존관계를 분석할 수 있었다.수안보 등 지역에서 나타난다 이러한 이상대 주변에는 대개 온천이 발달되어 있었거나 새로 개발되어 있는 곳이다. 온천에 이용하고 있는 시추공의 자료는 배제하였으나 온천이응으로 직접적으로 영향을 받지 않은 시추공의 자료는 사용하였다 이러한 온천 주변 지역이라 하더라도 실제는 온천의 pumping 으로 인한 대류현상으로 주변 일대의 온도를 올려놓았기 때문에 비교적 높은 지열류량 값을 보인다. 한편 한반도 남동부 일대는 이번 추가된 자료에 의해 새로운 지열류량 분포 변화가 나타났다 강원 북부 오색온천지역 부근에서 높은 지열류량 분포를 보이며 또한 우리나라 대단층 중의 하나인 양산단층과 같은 방향으로 발달한 밀양단층, 모량단층, 동래단층 등 주변부로 NNE-SSW 방향의 지열류량 이상대가 발달한다. 이것으로 볼 때 지열류량은 지질구조와 무관하지 않음을 파악할 수 있다. 특히 이러한 단층대 주변은 지열수의 순환이 깊은 심도까지 가능하므로 이러한 대류현상으로 지표부근까지 높은 지온 전달이 되어 나타나는 것으로 판단된다.의 안정된 방사성표지효율을 보였다. $^{99m}Tc$-transferrin을 이용한 감염영상을 성공적으로 얻을 수 있었으며, $^{67}Ga$-citrate 영상과 비교하여 더 빠른 시간 안에 우수한 영상을 얻을 수 있었다. 그러므로 $^{99m}Tc$-transierrin이 감염 병소의 영상진단에 사용될 수 있을 것으로 기대된다.리를 정량화 하였다. 특히 선조체에서의 도파민 유리에 의한 수용체 결합능의 감소는 흡연에 의한 혈중 니코틴의 축

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.5B
• /
• pp.385-394
• /
• 2012

The tactical mobile communication network, which comprises a part of the next-generation Tactical Information and Communication Network (TICN), provides means of communication and control for Tactical Multi-Functional Terminals (TMFT) belonging to a Mobile Subscriber Access Point (MSAP). The next-generation of MSAP is capable of constructing a backbone network via LCTR and HCTR directional antennas. At the same time, WMN modules are used to create and manage a wireless mesh backbone. When directional antennas are used in mobile environments, seamless services cannot be efficiently supported as the movement of the node prevents the angle of the antenna to constantly match. Therefore, data communication through the wireless mesh networks is required to provide direct communication between mobile MSAPs. Accordingly, mutual authentication and data encryption mechanisms are required to provide reliable data transmission in this environment. To provide efficient mutual authentication between MSAP devices, the process of verifying a certificate of the other MSAP device through its own authentication server is required. This paper proposes mutual authentication mechanisms where the MSAP requiring authentication and the MSAP that permits it initiates low-cost and efficient authentication in a distributed way. More specifically, we propose a method of applying EAP-ELS (Extensible Authentication Protocol-Transport Layer Security) in the next-generation TICN.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1113-1119
• /
• 2013

In this letter, a new approach is proposed for the design of a multi antenna for MIMO wireless devices. The proposed antenna covers various LTE(Long Term Evolution) service bands: band 17(704~746 MHz), band 13(746~787 MHz), band 5(824~894 MHz), and band 8(880~960 MHz). The proposed main antenna consists of a conventional monopole antenna with an inverted L-shaped slit for wideband operation. The proposed the LTE sub antenna is based on a switch loaded loop antenna structure, with a resonance frequency that can be controlled by capacitance of a logic circuit. The tuning technique for the LTE Rx antenna uses a RF MEMS(Micro-Electro mechanical system) to match the impedances to realize the bands of interest. Because the two proposed antennas are polarized orthogonally to each other, the ECC(Envelope Correlation Coefficient) characteristic between two antennas was measured to be very low (below 0.06) with an isolation characteristic below -20 dB between the two antennas in the operating overall LTE bands. The proposed antenna is particularly attractive for mobile devices that integrate LTE multiple systems.

• Journal of The Korean Association of Information Education
• /
• v.11 no.2
• /
• pp.139-146
• /
• 2007

Today, using RFID(Radio Frequency Identification) card is extended in diversity as medical treatment, circulation market, military affairs, manufacture, security, etc. The RFID technology is an automatic identification method, relying on storing and remotely retrieving data for the purpose of identification using radio waves. This advantage of the RFID will be as a replacement for traditional Barcoding. Besides, book-lending system and attendance management system become the center of educational institution in interest. This paper presents a attendance management system using the RFID card which provides directly information of attendance for professors with mobile and students with web. Also, the students only have ID card that embed RFID tag which is recognized attendance through DB that storages to is received a information of student from RFID card Reader. And it is possible management or report for attendance and time table not only for professors by management program but also for students by web program.