• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.3
• /
• pp.514-521
• /
• 2009

The current control for Interior-mounted Permanent Magnet Motor(IPM Motor) is more complicate than Surface-mounted Permanent magnet Motor(SPM Motor) because of its torque characteristic depending on the reluctance. For high performance torque control, it requirs state decoupling between d-axis current and q-axis current dynamics. However the variation of the inductances, which couples the state dynamics of the currents, makes the state decoupling difficult. So some decoupling methods have developed to cope this variation and each current can be regulated independently. This paper proposes a novel approach for fully decoupling the states cross-coupling using sliding mode control with virtual state for IPM Motor. As a result, in spite of the parameter uncertainty and disturbance, the proposed sliding surface can have the dynamics of nominal system controlled by PI controller.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.886-887
• /
• 2015

There is a growing interest in and demand for power industry acceleration and energy efficiency due to the increased energy consumption, environmental issues. Electronic power IT convergence industries such as intelligent power system has attract attention as new growth engine industry. A large number of sensors and motors are being installed following unmanned, automated in existing incoming panel management system. Observe the operating conditions and rapid response is essential. Despite the need for immediate action to be taken in the event of various later failed to recognize the emergency power can lead to accidents. In this paper, we propose a new architecture of the implementation of incoming panel monitoring system for power monitoring, fault detection, maintenance and system control using open source hardware platform and Wi-Fi networks.

• Polymer(Korea)
• /
• v.35 no.4
• /
• pp.302-307
• /
• 2011

The parameters of silanol formation reaction of organosilane including solvent type, solution concentration, pH and hydrolysis time influence the adhesion property of 2 layer flexible copper clad laminate (FCCL). Especially, the hydrolysis reaction time of silane coupling agent affects the formation of the silanol groups and their self-condensation to generate oilgomeric structure to enhance the surface treatment as an adhesive promoter. In our study, we prepared the binary silane coupling agents to control hydrolysis reaction rate and surface energy after treatment of silane coupling agents for increasing the adhesive property between a copper layer and a polyimide layer. The surface morphology of rolled copper foil, as a function of the contents of the coated binary silane coupling agent, was fully characterized. As fabricated 2-layer FCCL, we observed that adhesive properties were changed by hydrolysis rate and surface energy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.7-15
• /
• 2018

Drilling processes require a cutting monitoring function that can be analyzed and gives feedback about strange conditions, tool collision and tool wear in real time. In this study, we proposed a drill monitor using the torque from the main spindle in CNC machine tools and a PROFIBUS network as a PLC-based interface. This paper studied drilling torque changes depending on drill size, the repetition cutting of the drilling and the drill's wear in the same cutting conditions. The material of the drills was high speed steel (HSS) and uncoated. The drills chosen were 2.7 mm, 6.7 mm, and 10.0 mm in diameter. These drills were selected because they had basic holes for their taps.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2014

In recent years, much attention has been paid to the development of intelligent vehicles that integrate automotive technology into the information technology, with the aim of improving user friendliness and stability. The representative function is a autonomous driving and a cruise control. In designing such vehicles, it is critical to address the real-time issues (i.e., real-time vehicle control and timely response). However, previous research excluded the real-time scheduling. We develop a model car with unmanned cruise control, design the real-time scheduler using cyclic executive to easily adapt the model car, and provide some insight into potential solutions based on various experiments.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.161-164
• /
• 2008

A realization for EMG signal sensing and vertical control system of robotizing arm is presented in this paper. The system is realized that a fine EMG bio-signals of humans' arm muscle are detected by surface electrode sensor, making a high performance amplifier and filtering, converting analog into digital signal and driving a servomotor for robotizing arm. The system is experimented by monitoring multiple step vertical control angles of robotizing arm corresponding to EMG signals in moving arm muscles. The experimental result are that the vertical control level is measured to around 2 degrees and mean error is 5% approximately.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.753-758
• /
• 2020

In this paper, we intend to develop a control system that can apply the developed vertical stirring heater to the facility house and control the other facilities (circulating fan, ventilation fan, window using a switching motor, ceiling, and dehumidification). Through this, it is intended to increase the cultivation efficiency of crops and improve storage environment of crops held by non-heated storage or storage warehouses to increase the storage period and freshness. In addition, ICT monitoring technology is added to enable users to easily solve problems when there is a problem due to changes in the cultivation and storage environment with Real Time Control (RTC).

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.19-19
• /
• 2017

자율주행 트랙터를 위한 트랙터 조향제어는 일반적으로 전자모터를 이용한 EPS(Electric Power Steering) 시스템을 스티어링 휠에 연결하여 회전변위를 변경하고 그 결과 오비트롤(Orbitrol) 밸브의 토출유량을 바꾸고 호스로 연결된 조향실린더의 변위를 조절하여 최종적으로 전방 타이어의 방향각을 변경하면서 이루어진다. 이러한 조향방식은 시스템 구조상 조향실린더와 오비트롤 밸브가 상대적으로 멀리 떨어져 있으며, 밸브 특성상 약 ${\pm}5^{\circ}$의 오버랩이 포함되어 있다. 또한, EPS의 전자모터는 관성력, 마찰, 백래시 등의 영향을 가진다. 이와 같은 복합적인 영향은 조향 응답을 느리게 만들어 상대적으로 빠른 속도에서 주행에서 추종성능이 떨어지는 문제가 발생한다. 본 연구에서는 자율주행 트랙터의 조향성능 개선 연구의 일환으로 조향 HILS 시뮬레이터를 설계제작하여 조향 성능의 요인을 실험적으로 구명하고자 하였으며 이를 바탕으로 조향 시스템의 설계개선 방안을 수립하고자 하였다. 시뮬레이터는 동양물산 80 마력급 TX803 트랙터에 사용되는 오픈센터방식의 오비트롤 유압회로 시스템을 기어펌프가 장착된 AC모터로 구동되게 구성하였으며, 유량은 모터의 주파수를 조절 회전속도를 조절 변경하였다. 추가적으로 EPS와 오비트롤 조합의 조향성능을 비교 및 개선하기 위해 비례제어밸브(PVG 32, Danfoss)를 추가 장착하였다. 실제 트랙터 조향 시 나타나는 마찰저항을 모사하기 위해 부하 실린더를 구성하였으며, 조향 실린더의 부하의 크기는 부하 실린더를 폐회로를 구성하고 유량비례제어밸브를 이용한 유로의 개구량 조절을 통해 부하의 크기를 약 4000 N 까지 증가시킬 수 있도록 하였다. EPS와 비례제어밸브를 제어하기 위해 CANoe 8.0 소프트웨어를 이용하여 CAN통신 기반 가상 조향ECU를 구성하였으며 오비트롤의 기본 성능을 확인하기 위해 조향휠에 따른 실린더 동특성 및 계단 추종성능을 비례제어밸브와 비교하였다. 오비트롤 밸브는 약 ${\pm}5^{\circ}$이상 동작 시 실린더 압력이 상승하기 시작하였으며, 이후 약 ${\pm}10^{\circ}$이상 동작 시 조향실린더가 동작하기 시작하였다. 계단 추종성능실험에서는 비례제어밸브가 약 2배 이상의 응답개선을 나타냈다. 자율주행 경로추종 성능을 향상시키기 위해서는 순간적인 출력밀도가 높은 비례제어밸브를 통해 응답개선이 필요한 것으로 나타났다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.6
• /
• pp.197-202
• /
• 2016

In this paper, we propose optimal smart home security monitoring system. Proposeed optimal smart home security system using the three types of ultrasonic sensors were tested to obtain reliable data. and Using Raspberry Pi3, the smart home security system was implemented. In addition, It was verified through experiments optimal efficiency with a small amount compared to the conventional sensor of the home security system by the two ultrasonic sensors located in the optimal position. It was able to use two ultrasonic sensors to determine whether the intruder's highly efficient and reliable intrusion, and connect the servo motor at the bottom of the camera so you can shoot adjusted to the attacker's location to shoot the intruder's image. In addition, by using a Web server and stored the recorded image and two ultrasonic sensor data and provide a Web page for a user to monitor at all remote locations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3161-3167
• /
• 2010

Hall sensors of BLDC(brushless DC) motor are used to detect a position information for a control mechanism, which implements an algorithm for velocity and position control. Actual azimuth and altitude were measured to evaluate a control precision. The measurement revealed comparatively good accuracy that the measured values were $2.02^{\circ}$ and $1.01^{\circ}$ respectively, and the maximum error falls within $1.86^{\circ}$. The developed monitoring system of photovoltaic generation plants is a LCU(Local Control Unit) based on an integrated monitoring system which supports 1:N method for multiple simultaneous connections, remote control and real-time system state monitoring.