• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.409-409
• /
• 2023

하천 수위는 합리적인 수자원의 이용 및 관리를 위해 반드시 필요한 수문 자료이다. 우리나라에서는 수위 측정을 위해 유역 내에 관측소를 설치하여 장비 또는 인력을 통해 수위를 측정하고 있다. 하지만, 많은 관측소를 운영하고 관리하기에는 예산과 인력이 소모되는 한계가 있다. 위성 영상을 통한 시계열 분석은 전지구적 모니터링과 관측 분야에 중요한 역할을 수행할 것으로 기대되고 있으며, 특히 위성 영상자료를 활용한 수자원 분야 연구가 활발히 진행되고 있다. 위성 영상을 활용하여 수면적을 감지하고 수위와 유량을 판별하는 많은 연구가 진행되었지만, 하천 하상의 경사와 단면 형태에 따라 수면적이 변하여 정량적인 수위 추정에는 한계가 존재한다. 본 연구에서는 Sentinel-1의 SAR 영상과 InSAR 기법을 통해 낙동강 유역의 홍수 전후의 하천 수위 변화를 분석하였다. Sentinel-1 IW 모드의 Single Look Complex(SLC) 영상 12장과 ESA 영상 처리 툴인 SNAP을 활용하여 VV(Vertical-Vertical) 데이터의 간섭을 통해 센티미터(cm) 단위지표 변화에 따른 수위 변위를 분석하였다. 위성 영상을 통해 추출한 수위 변위와 계측 수위 및 단면 자료의 정합성을 비교한 결과, 제방과 수체 경계면 식생과 하상 세굴로 인한 오차로 정량적이 수위의 정합성에는 한계가 존재하였지만, 수위의 정량적인 변동성을 확인할 수 있었으며, 수위 변화의 반응속도를 판별할 수 있었다.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.418-424
• /
• 2023

In this study, we examined the effects of annealing on electrical characteristics of double-gated silicon nanosheet (SiNS) feedback field effect transistors (FBFETs). When bias stresses were applied for 1000 s, the double-gated SiNS FBFETs were more affected by positive bias stresses than negative bias stresses regardless of the channel mode owing to the increase of interface traps caused by electrons in the inversion layers. After annealing at 300 ℃ for 10 mins, the devices were completely recovered to their original properties, and the characteristics did not change anymore when bias stresses were applied again for 1000 s.

• The Journal of the Korean bone and joint tumor society
• /
• v.9 no.1
• /
• pp.84-92
• /
• 2003

Purpose: To report two cases of bone tumors other than osteoid osteoma in the proximal femur and treated with percutaneous high frequency radioablation method. Cases: We reviewed two cases with intracortical chondroma and enchondroma in the femoral head retrospectively. The patient with intracortical chondroma was a thirty one year old woman and had suffered right hip pain of 1 year duration. The lesion was located in the head of right femur and treated with CT guided percutaneous high frequency radioablation after needle biopsy under general anesthesia. The symptom was gone immediately after the procedure and was discharged postop. 1 day. 15 months has passed without symptom recurrence. Second case having enchondroma, was 56 year old woman complaining of gluteal area pain for 3 months. Radiologic evaluation showed osteolytic lesion with sclerotic rim on the inferior portion of the left femoral head. She received a same therapy with CT guided radiofrequency ablation following needle biopsy. She reported dramatic pain relief after the procedure and was discharged postop. 1 day. No symptom has occurred for 3 months until now. Conclusion: We present 2 cases of bone tumor occurred in the hip joint area other than osteoid osteoma which were treated with CT guided radiofrequency ablation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.208-208
• /
• 2009

최근 광섬유 센서기술의 수요는 전 산업분야에 걸쳐 높아지고 있으며, 이에 비례하여 기업 간, 국가 간 경쟁이 첨예화되고 있다. 또한 소형화, 경량화, 고성능화 센서에 대한 요구도 높아지고 있어 종래의 각종 센서들의 형태와 개선을 위한 연구개발이 매우 활발하게 전개되고 있으므로 이를 대체할 수 있는 광섬유 센서의 수요가 급격히 늘어날 전망이다. 기존 침입자 감지 시스템은 태풍, 낙뢰, 폭설, 폭우 등의 기상변화나 지반 흔들림, 통행차량 진동 및 전자기 간섭 등에 영향을 받아 오작동, 오경보가 빈번히 발생된다. 이러한 문제의 해결책으로 광섬유 센서 케이블을 이용한 시스템이 대안으로 부각되고 있다. 현재 국내에서 군부대, 공항을 중심으로 펜스와 휴전선 철책에 힘입자 감지를 위하여 도입되고 있다. 광섬유 센서 케이블을 사용하는 광망경비시스템은 광섬유 센서 케이블을 그물망 형태(광망)로 만들어 경계 지역에 설치된다. 광망경비시스템의 원리는 광섬유에 광펄스를 입사시켜 순환시키는데 침입자가 광망을 절단하거나 외력을 가할 경우 발생되는 레일리 산란에 기인하는 후방산란과 접속점과 파단점에서 생기는 반사광을 OTDR(Optical Time Domain Reflectometer)로 검출하여 침입상황 및 침입위치를 탐지한다. 그러나 이러한 침입자 감지를 위한 광망경비시스템의 핵심부품인 광섬유 센서 케이블은 기존에 전량 해외수입에 의존하고 있는 실정이며, 지금까지 국내에서 생산하기 위한 제작 기술과 노하우가 초보단계에 머물러 있다. 이러한 광섬유 센서 케이블 제작에 있어서 중요한 부분이 패키징 기술이라 할 수 있다. 이는 광섬유 센서를 일반적인 피복 구조로 패키징하게 되면, 센서 고유의 특성이 패키징 과정과 운반과정, 포설과정에서 변하게 되고 센서로써의 신뢰성이 크게 저하된다. 본 연구에서는 힘입자 감지용 광섬유 센서 케이블의 설계와 제작을 위한 제조공법을 확립하고, 이를 이용해 제작된 광섬유 센서 케이블의 신뢰성 특성을 평가하였다. 설계 제작된 광섬유 센서 케이블의 구조는 멀티모드광섬유(MMF) 에 0.9 mm Tight buffer를 코팅하고, 광심선 주위에 아라미드 얀을 삽입시킨 후 고문자 수지를 적용하여 외부 피복 (jacket)을 하였다. 제작된 광섬유 센서 케이블의 외경 측정결과 기준치 ($2.95\;{\pm}\;0.03$ mm)를 모두 만족하였고, 850 nm 파장에서의 광 손실 측정 결과 4.0 dB/km 이하였다. 또한 주요 항목의 신뢰성 특성 시험결과, 인장강도는 8~10 kg의 인장력을 갖으며 온도순환시험 ($-30^{\circ}C\;{\sim}\;+75^{\circ}C$)에서의 광 손실은 0.6 dB 이하로 나타나 침입자 감지용 광섬유 센서 케이블로 적합함을 확인할 수 있었다.

• The KIPS Transactions:PartA
• /
• v.14A no.2
• /
• pp.77-84
• /
• 2007

The intima media thickness(IMT) of the carotid artery from B mode ultrasound images has recently been proposed as the most useful index of individual atherosclerosis and can be used to predict major cardiovascular events. Ultrasonic measurements of the IMT are conventionally obtained by manually tracing interfaces between tissue layers. The drawbacks of this method are the inter and intra observer variability and its inefficiency. In this paper, we present a multiresolution snake method combined with the dynamic programming, which overcomes the various noises and sensitivity to initialization of conventional snake. First, an image pyramid is constructed using the Gaussian pyramid that maintains global edge information with smoothing in the images, and then the boundaries are automatically detected in the lowest resolution level by minimizing a cost function based on dynamic programming. The cost function includes cost terms which are representing image features and geometrical continuity of the vessel interfaces. Since the detected boundaries are selected as initial contour of the snake for the next level, this automated approach solves the problem of the initialization. Moreover, the proposed snake improves the problem of converging th the local minima by defining the external energy based on multiple image features. In this paper, our method has been validated by computing the correlation between manual and automatic measurements. This automated detection method has obtained more accurate and reproducible results than conventional edge detection by considering multiple image features.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.17-26
• /
• 2018

If a photovoltaic (PV) system is installed in a primary feeder interconnected with the PV system, bi-directional power flow can occur, and then, the magnitude and direction of the fault current can change, depending on the fault location and point of common coupling (PCC) of the PV system, and the time current curve (TCC) cannot be properly coordinated between protection devices. Also, it is difficult to obtain a proper time interval for protection devices because the conventional setting approach is applied, even though the PV system is installed and operating. Therefore, this paper presents three operation modes considering the operational conditions of the PV system to obtain setting values for protection devices. Based on the mode, this paper proposes an algorithm to calculate the optimal protection coordination time interval according to the introduction capacity of the PV system. In addition, this paper performs modelling of a distribution system with the PV system and protection devices by using Off-DAS S/W, and analyzes the characteristics of the time interval between the protection devices, such as substation relays, reclosers, customer relays, and PV customer relays. The simulation results confirmed that the proposed operational modes and setting-value algorithms are useful and effective for protection coordination in a distribution system for a PV system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.394-402
• /
• 2013

This paper presents design, fabrication and ruggedness test of switching-mode power amplifier using GaN(Gallium Nitride) HEMT(High Electron Mobility Transistor) for S-band radar applications. The power amplifier is designed to Class-F for high efficiency. The input signal for the measurement of the power amplifier is pulse signal at $100{\mu}s$ pulse width and duty cycle of 10 %. The measurement results of the fabricated Class-F power amplifier are a power gain of 10.8 dB, an output power of 40.8 dBm, a power added efficiency(PAE) of 54.2 %, and a drain efficiency of 62.6 %, at the center frequency. We proposed reliability test set-up of a power amplifier for ruggedness test. And we measured output power and efficiency according to VSWR(Voltage Standing Wave Ratio) variation. The designed power amplifier achieved output power of 32.6~41.1 dBm and drain efficiency of 23.4~63 % by changing VSWR, respectively.

• Korean journal of applied entomology
• /
• v.32 no.3
• /
• pp.354-371
• /
• 1993

Behavior of adult females of the smoky brown cockroach was observed for 10-15 days continuously by using computer and the automatic sensoring system. Under the light condition of l2L~ 12D, individual variations were generally higher and the periodicity appeared less in terms of the presence time at the micro-habitats and the locomotory activity. The smoky brown cockroach appeared 20.42, 11.50, 6.31 and 2.66 % in a day in averages respectively at the shelter and the places for other individuals, feeding and drinking. It stayed 20.29 % in a day at the shelter when food, water, and other individuals were not supplied. Visiting rates were higher at the feeding and dnnking places than at. the ot.her micro-habitats. The degree of t.he locomotory activity was relatively lower when food, water, and other individuals were not supplied t.han when they were supplied. The Pnncipal Component Analysis (PCA) on the presence at the micro-habitats showed that. t.he presence pattern for each mdividual appeared differently (Q mode) while the differem time zones were grouped to the photophase and scotophase (R mode). When food, water, and other individuals were supplied the degree of grouping was higher at the shelter than at the places for feeding and drinking. When the act.ivityand the presence time at the different micro-habitats were jointly analyzed by PCA, the achvity of the female smoky brown cockroach appeared in relation with the presence time ( %) at the places for feeding and other individuals.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.65-70
• /
• 2008

The mechanical shear strength of BGA(Ball Grid Array) solder joints under high impact loading was investigated. The Sn-37Pb solder balls with a diameter of $500{\mu}m$ were placed on the pads of FR-4 substrates with ENIG(Electroless Nickel Immersion Gold) surface treatment and reflowed. For the High Temperature Storage(HTS) test, the samples were aged a constant testing temperature of $120^{\circ}C$ for up to 250h. After the HTS test, high speed shear tests with various shear speed of 0.01, 0.1, 1, 3 m/s were conducted. $Ni_3Sn_4$ intermetallic compound(IMC) layer was observed at the solder/Ni-P interface and thickness of IMC was increased with aging process. The shear strength increased with increasing shear speed. The fracture surfaces of solder joints showed various fracture modes dependent on shear speed and aging time. Fracture mode was changed from ductile fracture to brittle fracture with increasing shear speed.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.278-284
• /
• 2006

We have fabricated and measured electrooptic modulator using coupled stack InAs/InGaAs quantum dots. The height of the quantum dot is 16 nm and quantum dots are stacked including an InGaAs capping layer. The peak wavelength of photoluminescence is 1260 nm at room temperature and 1158 nm at 12 K. The operation characteristics of the quantum dots show high modulation efficiency of electrooptic modulator at 1550 nm compared to that of existing III-V bulk and MQW type semiconductor. The measured switching voltage ($V\pi$) is 540 and 600 mV, for TE mode and TM mode, respectively. From the results, the modulation efficiency can be determined as 333.3 and $300^{\circ}/V{\cdot}mm$ for TE and TM modes. The results reported here may lead to the design and fabrication of a novel electrooptic modulator with low switching voltage and high efficiency.