• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.1 no.2
• /
• pp.91-98
• /
• 2008

Domestic standard for Korean T-DMB includes MPEG-4 BSAC (Bit Sliced Arithmetic Coding) audio coding that has been established in 2003. This paper presents an implementation and optimization of MPEG-4 BSAC Audio Decoder on ARM926EJ-S processor. Tools and modules of the BSAC audio decoder were implemented with 32-bit fixed point operations. Further optimization was accomplished using ARM926EJ-S Inline Assembly. The optimization was based on the total number of multiplications and MAC (Multiply and Accumulation) operations causing most of core cycles of ARM926EJ-S, and also based on analysis of ARMv5 instructions. The result of optimization was evaluated on the basis of MIPS (Million Instruction per second). Implementation results show that BSAC bitstream at 96kbps can be decoded in real-time at 65MHz CPU clocks.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.11 no.1
• /
• pp.64-72
• /
• 2001

This paper is on a design of the high-speed cipher IC using IDEA algorithm. The chip is consists of six functional blocks. The principal blocks are encryption and decryption key generator, input data circuit, encryption processor, output data circuit, operation mode controller. In subkey generator, the design goal is rather decrease of its area than increase of its computation speed. On the other hand, the design of encryption processor is focused on rather increase of its computation speed than decrease of its area. Therefore, the pipeline architecture for repeated processing and the modular multiplier for improving computation speed are adopted. Specially, there are used the carry select adder and modified Booth algorithm to increase its computation speed at modular multiplier. To input the data by 8-bit, 16-bit, 32-bit according to the operation mode, it is designed so that buffer shifts by 8-bit, 16-bit, 32-bit. As a result of simulation by 0.25 $\mu\textrm{m}$ process, this IC has achieved the throughput of 1Gbps in addition to its small area, and used 12,000gates in implementing the algorithm.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.2
• /
• pp.3-11
• /
• 2011

Evaluation of cube roots in characteristic three finite fields is required for Tate (or modified Tate) pairing computation. The Hamming weights (the number of nonzero coefficients) in the polynomial representations of $x^{1/3}$ and $x^{2/3}$ determine the efficiency of cube roots computation, where $F_{3^m}$is represented as $F_3[x]/(f)$ and $f(x)=x^m+ax^k+b{\in}F_3[x]$ (a, $b{\in}F_3$) is an irreducible trinomial. O. Ahmadi et al. determined the Hamming weights of $x^{1/3}$ and $x^{2/3}$ for all irreducible trinomials. In this paper, we present formulas for cube roots in $F_{3^m}$ using the shifted polynomial basis(SPB). Moreover, we provide the suitable shifted polynomial basis bring no further modular reduction process.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.736-741
• /
• 2022

Lattice-based cryptography is the most practical post-quantum cryptography because it enjoys strong worst-case security, relatively efficient implementation, and simplicity. Ring learning with errors (R-LWE) is a public key encryption (PKE) method of lattice-based encryption (LBC), and the most important operation of R-LWE is the modular polynomial multiplication of rings. This paper proposes a method for optimizing modular multipliers based on approximate computing (AC) technology, targeting the medium-security parameter set of the R-LWE cryptosystem. First, as a simple way to implement complex logic, LUT is used to omit some of the approximate multiplication operations, and the 2's complement method is used to calculate the number of bits whose value is 1 when converting the value of the input data to binary. We propose a total of two methods to reduce the number of required adders by minimizing them. The proposed LUT-based modular multiplier reduced both speed and area by 9% compared to the existing R-LWE modular multiplier, and the modular multiplier using the 2's complement method reduced the area by 40% and improved the speed by 2%. appear. Finally, the area of the optimized modular multiplier with both of these methods applied was reduced by up to 43% compared to the previous one, and the speed was reduced by up to 10%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1195-1202
• /
• 2010

When modelling lots of induction motors to design and configure an engine room simulator, the 2 parameters equivalent circuit has many practical benefits as it reduces working hours considerably without requiring complicated technical data from makers except the ratings of motors. The basic properties such as torque and load current are shown well matched with real cases by this method, but almost the only drawback of 2 parameters circuit is that it reveals inherently higher power factor in the whole operation range due to disregarding the exciting current of the induction motor to maximize the simplification. This paper suggests a modelling module as a practical tool to compensate the power factor by inserting a virtual compensation current into the load current from 2 parameters equivalent circuit, and the simulated results show satisfactory outputs and the improved power factor indication by performance curves when compared to the cases of 2 parameters-equivalent circuit.

• Journal of Navigation and Port Research
• /
• v.29 no.3 s.99
• /
• pp.251-256
• /
• 2005

Today's port system,; require larger and faster operation of transfer cranes in order to accommodate rapidly increasing traffic. These cranes need precise control of their components for operational efficiency. This paper presents an IEEE 1451 based smart module that allows numerous sensors and actuators of the crane to attach themselves to various networks more easily. The smart module has been experimentally evaluated on a CAN network for its performance.

• Journal of IKEEE
• /
• v.7 no.1 s.12
• /
• pp.56-62
• /
• 2003

In this paper, we designed a adder and a multiplier using current mode T-gate on $GF(2^2)$. The T-gate is consisted of current mirror and pass transistor, the designed 4-valued T-gate used adder and multiplier on $GF(2^2)$. We designed its under 1.5um CMOS standard technology. The unit current of the circuits is 15㎂, and power supply is 3.3V VDD. The proposed current mode CMOS operator have a advantage of module by T-gate`s arrangement, and so we easily implement multi-valued operator.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.3
• /
• pp.211-219
• /
• 2002

In this paper, a new architecture that can simultaneously process modular multiplication and squaring on GF(2$^{m}$ ) in m clock cycles by using the cellular automata is presented. This can be used efficiently for the design of the modular exponentiation on the finite field which is the basic computation in most public key crypto systems such as Diffie-Hellman key exchange, EIGamal, etc. Also, the cellular automata architecture is simple, regular, modular, cascadable and therefore, can be utilized efficiently for the implementation of VLSI.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.886-889
• /
• 2006

수치연산 보조프로세서로도 알려져 있는 부동 소수점 연산장치(FPU)는 컴퓨터가 사용하는 기본 마이크로프로세서보다 더 빠르게 숫자를 다를 수 있는 특별한 회로 설계 또는 마이크로프로세서를 말한다. FPU는 전적으로 대형 수학적 연산에만 초점을 맞춘 특별한 명령 셋을 가지고 있어서 그렇게 빠르게 계산을 수행할 수 있는 것이다. FPU는 오늘날의 거의 모든 PC에 장착되고 있지만, 실은 그것은 그래픽 이미지 처리나 표현 등과 같은 특별할 일을 수행할 때에 필요하다. 초창기 컴퓨터 회사들은 각기 다른 연산방식을 사용했다. 이에 따라 연산결과가 컴퓨터마다 다른 문제점을 해결하기 위해 IEEE에서는 부동 소수점에 대한 표준안을 제안하였다. 이 표준안은 IEEE Standard 754 이며, 오늘날 인텔 CPU 기반의 PC, 매킨토시 및 대부분의 유닉스 플랫폼에서 컴퓨터 상의 실수를 표현하기 위해 사용하는 가장 일반적인 표현 방식으로 발전하였다. 본 논문에서는 부동 소수점 표준안 중 32-bit 단일 정밀도 부동 소수점 가산기를 VHDL로 구현하여 FPGA칩으로 다운하고 PCI 인터페이스를 통해 Visual C++로 데이터의 입출력을 검증하였다.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2009.01a
• /
• pp.241-244
• /
• 2009

최근 모바일폰에 500만 화소 이상의 카메라 모듈이 장착되는 등 모바일 장치에서 고해상도 영상의 인코딩 및 디코딩에 대한 요구가 크게 늘어남에 따라 저성능 시스템에서 실시간으로 동작하는 영상 코덱 구현에 대한 필요성이 증대되고 있다. 본 논문은 JPEG 디코딩의 마지막 단계인 컬러변환 과정에 대해 계산 복잡도를 최적화하는 기법을 제안하고 성능을 평가하였다. 제안된 기법은 JPEG 디코딩 과정에서 IDCT(Inverse Discrete Cosine Transform) 변환과 컬러변환 간의 선형성을 바탕으로 이들 연산 순서를 재배열함으로써 컬러변환 과정에서 요구되는 계산 횟수를 줄이고, 재배열된 부동소수점 연산에 대해 정수 맵핑을 적용하여 계산 복잡도를 줄임으로써 실행시간을 최적화하였다. 임베디드 시스템 개발 플랫폼에서의 성능 평가를 통해 제안된 기법이 기존의 컬러변환 기법들과 비교하여 실행시간을 크게 단축함을 얄 수 있었으나 복원 영상의 화질이 상대적으로 저하됨을 확인하였다.