• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.399-405
• /
• 2008

콘크리트 슬래브 표면의 영상처리 목적은 구조물의 균열발생을 최소화하고 발생한 균열에 대해서 지속적인 기록 관리로 균열의 진행 상태를 분석하여 보수시기 및 보수공법 적용의 합리적 운영체계를 수립하고자 하는 것이다. 일반적으로 콘크리트에서의 균열은 육안으로 분간할 수 있을 정도로 큰 반면 프리스트레스트 콘크리트의 균열은 기기를 사용하여야 측정, 분별할 수 있다. 본 논문에서는 균열의 명함도와 인접한 표면의 명함도 차이를 이용하여 균열과 잡음을 분리한다. 그리고 균열과 잡음 영역에서 형태학적인 정보를 이용하여 잡음 영역만을 제거한다. 잡음 영역이 제거된 균열 영역에서도 미세한 잡음이 존재하므로 균열 영역을 평활화를 한 후, 미세 잡음을 하나의 객체로 인식하여 제거하고 끊어진 영역의 균열을 미디언 필터를 이용하여 균열을 연결한다. 그리고 제안된 방법으로 추출된 균열을 원본 영상에 적용하여 최종적으로 균열만을 검출한다. 검출된 균열에서 균열의 특정부분을 선택하고 선택되어진 균열 영상을 대상으로 균열의 길이, 방향, 폭을 순차적으로 분석한다. 실제 균열 영상을 대상으로 실험한 결과, 균열이 비교적 정확히 검출되었고 균열 검사기가 한번에 측정할 때에 비해 비교적 빠르고 적은 노력으로 측정할 수 있는 것을 확인하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.379-385
• /
• 2008

콘크리트 건물의 보수 작업은 표면에 발생하는 균열을 정확하게 계측함으로써 비용적인 측면과 안전성이 결정된다. 하지만 표면에 발생한 균열은 대부분 점검자에 의해 수작업으로 계측되기 때문에 시간적 측면에서 비효율적이다. 따라서 본 논문에서는 콘크리트 슬래브 표면에 발생한 균열의 밝기와 밀도 그리고 면적 특징을 이용한 균열 검출 기법을 제안한다. 제안된 균열 검출 방법은 콘크리트 슬래브 표면의 명암도와 위치 정보를 ART2 기반 양자화에 적용한 후, 균열과 인접한 배경간의 명암도 차이를 이용하여 균열과 인접한 배경을 분리한다. 균열과 인접한 배경이 분리된 영상에서 형태학적인 정보를 이용하여 세부적인 잡음을 제거한 후에 최종적으로 균열 영역을 검출한다. 실제 콘크리트 균열 영상을 대상으로 실험한 결과, 다양한 콘크리트 균열 영상에서 기존의 방법보다 균열 검출 성능이 개선되었음을 확인하였다.

• Journal of Power System Engineering
• /
• v.16 no.1
• /
• pp.72-77
• /
• 2012

Acoustic emission (AE) is known to be sensitive to fracture process and so it was expected that AE data may propose as a means of monitoring the fracture information. The aim of this study is to analyze the characteristic of AE signal emitted from glass during Vickers indentation. To observe AE characteristics by surface effect, both glass and coating glass were studied. During Vickers indentation loading, AE signal resulted from penny-like crack is detected. During Vickers indentation unloading, AE signal resulted from both radial/median crack and lateral crack is detected. In case of indentation on glass, the emission energy(${\epsilon}$) is found to be approximately proportional to the fourth power of the crack length. In case of indentation on coating glass, the emission energy(${\epsilon}$) is approximately proportional to the crack length.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.2
• /
• pp.125-131
• /
• 2002

we analyzed acoustic emission signals obtained from three kinds of brittle materials under compression load by Vickers hardness tester. The results obtained can be summarized as follows; The signal in each material could be divided into three signal based on the properties of load. All specimens were not detected acoustic emission signals in stage II which was load constant region., and were detected in stage I and stage III. Glass was detected high amplitude signals in stage III. $Al_2O_3\;and\;Al_2O_3/Sic$ were detected high amplitude signals in stage I.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.61-65
• /
• 2001

The fracture toughness of ceramics can be measure by such various methods as DT (double torsion), CN (chevron notch) etc. But, the application of these methods to the engineering ceramics is very difficult because of its very high hardness. So, IF (indentation fracture) method is generally used for the evaluation of fracture toughness of ceramics. The Median crack induced by the sharp Vickers indenter was compared with the detected AE (acoustic emission) signal. On the silicon nitride ceramics, the AE test results agree fairly well with the median crack occurance and growth process. But, on the alumina, very many complicated crack signals were detected besides median crack. It can be considered that the IF methods must be used in limited engineering ceramics materials.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.2
• /
• pp.69-74
• /
• 2013

In this study, the crack healing effects of $Al_2O_3$ ceramics based on the heat treatment conditions were investigated. The influence of the additive amounts of SiC nanoparticles and the cycling process of indentation-heat treatment on the crack healing effect of $Al_2O_3$ ceramics were also examined. Three-point bending tests were carried out and the morphological changes in the fracture surface were observed by using FE-SEM. As a result, heat-treated samples in a vacuum or air atmosphere showed improved bending strengths compared to un-heat treated samples. This means that cracked specimens can be healed by heat treatment in a vacuum or air atmosphere. The crack healing effect of $Al_2O_3$ ceramics that were heat treated in an air atmosphere was much higher than that of those heat treated in a vacuum. After heat treatment, the $Al_2O_3$ ceramics with 30 wt% SiC nanoparticles showed a higher bending strength than those with 15 wt% SiC. The cyclic indentation and heat treatment did not remarkably affect the crack healing effect. The SEM images showed that the median crack, indenter mark on the surface, and pores in the fracture surface of a specimen almost disappeared after being heat treated in an air atmosphere.