• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.153-159
• /
• 2007

Nano-Particles are influenced on the environmental protection and human health. The relationships between transient vehicle operation and nano-particle emissions are not well-known, especially for diesel passenger vehicles with DPF. In this study, a diesel passenger vehicle was measured on condition of DPF regeneration and no regeneration on a chassis dynamometer test bench. The particulate matter (PM) emission from this vehicle was measured by its number, size and mass measurement. The mass of the total PM was evaluated with the standard gravimetric measurement method while the total number and size concentrations were measured on a NEDC driving cycle using Condensation Particle Counter (CPC) and EEPS. Total number concentration by CPC was $1.5{\times}10^{1l}N/km$, which was 20% of result by EEPS. This means about 80% of total particle emission is consist of volatile and small-sized particles(<22nm). During regeneration, particle emission was $6.2{\times}10^{12}N/km$, was emitted 400 times compared with the emission before regeneration. As for the particle size of $22{\sim}100nm$ was emitted mainly, showing peak value of near 40nm in size. This means regeneration decreased the mean size of particles. Regarding regeneration, PM showed no change while the particle number showed about 6 times difference between before and after regeneration. It seems that the regeneration influences on particle number emissions are related to DPF-fill state and filtration efficiency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.2
• /
• pp.57-62
• /
• 2000

The effect of exhaust gas recirculation(EGR) on the characteristics of exhaust gas emissions, and SFC are experimentally investigated by four-cylinder, four-cycle and direct injection marine diesel engine. In order to reduce the soot contents in the recirculated exhaust gas to intake system of the engines, a soot removal system of a cylinderical-type scrubber is specially designed and manufactured for the experimental system. (1) SFC is increased in downward convex curve style with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio. (2) NOx emission is reduced in downward convex curve style with increasing excess air ratio, it is reduced with increasing EGR rate at the same excess air ratio. (3) Soot emission is decreased in downward convex curve style with increasing excess air ratio, it is reduced with increasing EGR rate at the same excess air ratio. (4) CO emission is increased in nearly straight line style with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio. (5) HC emission is not constant tendency with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio.

• Journal of ILASS-Korea
• /
• v.29 no.2
• /
• pp.68-74
• /
• 2024

As awareness of environmental pollution problems increases worldwide, interest in air pollutants is increasing. In particular, NOx and PM, which are major pollutants in diesel vehicles, are contributing significantly to emissions. As a result, its importance is increasing. In this study, based on research results applied to large diesel vehicles, the problem of natural regeneration caused by low exhaust gas temperature during low speed and low load operation is solved by applying a complex regeneration DPF that is not affected by temperature conditions to small diesel vehicles. The feasibility of application to small diesel vehicles was reviewed by measuring the emission reduction efficiency. As a result of the engine test, the power reduction rate and fuel consumption rate before and after device installation under full load conditions were 2.9% decrease and 3.5% increase, respectively, satisfying the standard for a 5% reduction, and as a result of the regeneration equilibrium temperature (BPT) test, the regeneration temperature was 310℃. appeared at the level. The reduction efficiency test results for the actual vehicle durability test equipment showed 97.3% PM, 51.0% CO, and 31.1% HC, while the city commuter vehicle had PM 97.5%, CO 61.7%, HC 40.0%, and the school bus vehicle had PM 96.8%, CO 44.4%, HC 34.3%, and low-speed logistics vehicles showed a reduction efficiency of 98.2% for PM, 36.0% for CO, and 45.7% for HC. Based on the results of this study, in the future, it is necessary to secure DPF technology suitable for all vehicle types through actual vehicle application research on temperature condition-insensitive composite regenerative DPF for medium-sized vehicles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.8
• /
• pp.657-663
• /
• 2014

Since 2007, the defect confirmation test for vehicles using PEMS has been enforced in USA. This test can measure emissions from on-street vehicles using a device mounted on a car. Europe has confirmed its plan for introducing this test from EURO6, 2013. Thus, the Korean government is also under pressure to adopt this method that reflects the real-world driving conditions using PEMS, considering the emission controls for domestic heavy-duty vehicles. To provide various utilizations of the PEM, this emission test has been developed in accordance with the type of driving road, DPF, ISG, and air conditioner. This research aims to provide the fundamental materials for implementing defect confirmation tests for commercial vehicles, which are appropriate for domestic emission control situations, after studying the defect confirmation test methods for heavy-duty vehicles using PEMS.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.27-33
• /
• 2020

NOx, PN and CO emissions from diesel trucks make up a significant portion of domestic air pollutant emissions. Therefore, test vehicles with various emission standards and driving modes were selected to evaluate the emission characteristics of regulated pollutants (NOx, PN, CO) in medium-duty trucks. As a result of test, all test vehicles were satisfied with Euro 5 or 6 regulation. NOx emissions of Euro 6 vehicles with after-treatment of LNT + DPF were lower than those of Euro 5 vehicles with DPF. In WLTC mode, all vehicles have high NOx emissions at section of extra high speeds, which are determined by increased fuel consumption and high combustion temperatures. CO and PN emissions from all vehicles were found to be low at section of low speeds. Also, The NO₂/NOx ratio was analyzed at 7-23% in each mode, and the NO₂/NOx ratio increased as the average vehicle speed increased. In NIER 9 mode, the CO, HC, and PN emissions were higher under cold conditions of engine than hot conditions of engine. In addition, vehicles with after-treatment system of LNT have similar NOx emissions level in this study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.83-83
• /
• 2010

산업이 고도화되는 과정에서 에너지의 고효율화를 위하여 고온, 고압 등의 극한환경 하의 공정이 불가결하며, 이에 따라 초미세분진인 나노 입자가 증가되고 있다. 이에 따라 해당 나노의 입자 처리를 위하여 다양한 용도에서의 고온 필터가 산업적으로 요구되고 있다. 본 연구에서는 디젤엔진 매연저감 후처리 장치, 소각로, 발전소 등의 미세 분진 포집 필터로서의 응용을 위해, 카본 파이버에 SiC 휘스커를 증착하는 실험을 진행하였다. 휘스커 증착 공정은 촉매없이 SiC 휘스커를 카본 파이버 위에 화학증착하였다. 휘스커 성장 시 증착 조건의 변화를 통하여 다양한 휘스커의 증착 형태 및 미세구조를 관찰하였다. 또한 높은 포집 효율 및 기체투과도를 갖추기 위해, 휘스커가 증착된 시편의 포집효율 및 기체투과도 향상을 위한 실험을 진행하였다. 해당 실험의 결과로, 증착된 필터는 70% 이상의 포집효율을 보이면서도 기체 투과도는 현재 상용화되어 있는 코디얼라이트보다 5배 이상 높았다. 또한 필터에 추가적인 SiC 침윤공정을 통하여 시편의 내산화성, 내마모성, 내열성 등의 특성이 향상됨을 확인하였다.

• Journal of Institute of Convergence Technology
• /
• v.1 no.1
• /
• pp.41-47
• /
• 2011

With the world-wide demand on the emission minimization, the needs on the diesel aftertreatment devices with high efficiency are also increasing. In order to effectively develop or design a high-performance diesel particulate filter, a clear understanding on the deposition and regeneration mechanism is required. In the present study, a theory on the lumped parameter model for wall-flow type diesel particulate filters is described focusing on the deposition efficiency, pressure drop inside the filter. The fourth order explicit Runge-Kutta method is utilized for the mass flow rate computation. Engine operation modes with controlled and uncontrolled regeneration options are selected. The computational lumped parameter model is validated by comparing the computed results with the measured data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.196-205
• /
• 2016

The exhaust gas discharged by cars not only threatens the health of the human body, but also contributes to global warming, due to the resulting increase in the concentrations of ozone, fine dust and carbon dioxide. Therefore, the government has steadily implemented careful inspection systems for exhaust emissions, in order to efficiently regulate the exhaust gas of cars. Studies on reducing the exhaust emissions of automobiles have been conducted in various fields, including ones designed to reduce the generation of HC, NOx, and $CO_2$ in the exhaust emission of vehicles. However, there have been insufficient studies on the reduction of the exhaust emission for old diesel vehicles. To develop careful inspection systems for the exhaust emissions of old diesel vehicles, studies on the reduction of the exhaust emissions and improvement of power are necessary by cleaning the carbon sediment in both the intake manifold and injector. Therefore, in this study, we analyzed and compared the amounts of gas emitted when simultaneously cleaning or not cleaning the intake manifold and injector of diesel automobiles with mileages over 80,000 km and operating periods over 5 years. The experimental results showed that in the case where the intake manifold and injector were simultaneously cleaned, there was a decline of 75.2% in the gas emission compared to the cases where only the manifold or injector is cleaned. Also, it was found that simultaneously cleansing the intake manifold and injector enabled the exhaust standard to be satisfied for less than 30% within 8.5 sec.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.69-69
• /
• 2017

농기계의 대형화, 고성능화로 장치가 복잡해지면서 안전표지 및 조작표시의 역할이 증대되고 있으나 기존에 제정된 KS B 7947의 경우 ISO표준 도안 및 작도방법을 준용하지 않고 있어 기호가 조잡하고 복잡하며 명확히 이해하기 어려워 산업체의 활용도가 낮은 상황이며, 제조사별로 상이한 도안을 사용하고 있는 실정이다. 따라서 ISO표준 도안 및 작도방법을 준용하여 그래픽 심볼 도안을 개정하여 산업체의 활용도가 높아져 조작표시를 농업인이 쉽게 인식하고 이해하여 위험 등을 피할 수 있도록 하여 사고 예방에 기여할 수 있도록 하는 것이 중요할 것이다. 본 연구에서는 안전표지 및 조작표시를 ISO 표준 도안 및 작도방법을 준용하여 작성하기 위한 방법을 연구하고 KS B-7946에 제시된 65개 항목 중 일본과 미국에서 동시에 사용되고 있는 항목 4개는 유지하고 10개 항목은 삭제하며, 승용 동력운반차, 매연저감 장치 등 11개 항목을 추가하고 40개 항목의 수정을 통하여 국내 농기계 관련 안전표지 및 조작표시의 그래픽 심볼을 개선하고 그 결과를 ISO에 국제표준 규격도안 추가 및 개정을 제안하고자 수행되었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.394-401
• /
• 2005

A nonthermal plasma-assisted fuel reformer was developed and the effects of operating variables on the performance of this reformer were studied. The $H_2$-rich reformed gas from the reformer was injected into a diesel engine under an idle condition and the effects of the amount of injected gas on the NO and soot reduction were investigated. It was found that with increasing electric power consumption, the degree of facility of ignition of the reforming reaction in the reformer could be enhanced. The performance of the reformer including $H_2$ concentration, $H_2$ recovery, and energy conversion was affected only by the O/C mole ratio. This was because the equilibrium reaction temperature was governed by the O/C mole ratio. With increasing O/C mole ratio, the $H_2$ recovery and energy conversion passed through the maximum values of 33.4% and 66%, respectively, at an O/C mole ratio between 1.2 and 1.5. The reason why the $H_2$ recovery and energy conversion increased with increasing O/C mole ratio when the O/C mole ratio was lower than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction occurred more enough with increasing O/C mole ratio in this low O/C mole ratio range and accordingly the reaction temperature increased. Whereas the reason why the $H_2$ recovery and energy conversion decreased with increasing O/C mole ratio when the O/C mole ratio was higher than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction was further advanced and the $H_2$ recovery and energy conversion decreased. As the weight ratio of reformed diesel to total diesel which entered the diesel engine was increased to $18.2{\sim}23.5%$, NO and soot reduction efficiencies increased and reached as values high as 68.5% and 23.5%, respectively.