• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.77-85
• /
• 2000

There are many weld defects such as surface crack, lack of fusion, and incomplete penetration (IP) in the butt joint weld of existing steel bridges. The crack-like defects may significantly reduce the fatigue life of the structure. This paper presents the procedure and the results of the fatigue life assessment of the butt joints with weld defects in the existing steel girder bridge. The butt joint welds with incomplete penetration were instrumented with strain gages to determine the stress histogram under normal traffic. Based on the measured stress histogram the crack propagation analysis were performed for the fatigue life assessment. By using the suggested procedure and methodology, one can decide the time of periodic inspection and the necessity of repair of the butt joint welds with serious weld defects in the existing steel bridge.

• Journal of Welding and Joining
• /
• v.30 no.2
• /
• pp.47-53
• /
• 2012

This paper aimed to study and understand the mechanical phenomena of thermal elasto-plastic behavior on the dissimilar butt joint (Al 6061-T6 and STS304) by TIG assisted Friction Stir Welding. Heat conduction and residual stress analysis is carried out using in-house solver. Two-dimensional results of the heat distribution and residual stresses in dissimilar joint for particular tool geometry and material properties are presented. The predicted stress along longitudinal direction in Al 6061-T6 and STS304 are approximately between 12-15% of their respective yield strengths. A comparison is made between experimentally measured and numerically predicted equivalent residual stress values.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.92-96
• /
• 2010

Recently, the application of aluminum alloys has been increasing for lightweight and high quality transport vehicles. Therefore, the proposal has been made to apply high speed hybrid welding methods to the marine grade aluminum alloy (A5052) used for shipbuilding by combining a 3-KW CW Nd : YAG laser and the MIG welding process. In this study, the characteristics of the welding parameters were investigated for a hybrid butt joint. This paper also describes the determination of the heat distribution in a weldment and the welding residual stress using a finite element method. Mechanical experimentation was also used to ascertain the reliability of the weldment.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.2
• /
• pp.62-66
• /
• 2010

The goal of this work is to establish the reliability of FCA welded joints for high strength EH36-TMCP ultra thick plate. For this, heat conduction and thermo elasto-plastic analyses have been conducted on a multi-pass, X-groove, butt-joint model to clarify the thermal and mechanical behavior (residual stresses, magnitude of the stresses, and their production and distribution mechanisms) of the weld joint. In addition, the results of the welding residual stress obtained from thermo elasto-plastic analysis was verified and compared with results obtained by XRD analysis.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.94-94
• /
• 2009

The purpose of this study is to identify the principal factor controlling transverse residual stress at the weldment for joining unit hull blocks. In order to do it, the comprehensive FE analyses were carried out to evaluate the effect of distance between fillet and butt weldments, in-plane and out-of-plane restraint degree on the amount and distribution of transverse residual stress in way of the weldments between unit hull blocks. In accordance with FEA results, principal factor controlling the amount of transverse residual stress at the weldments was identified as in-plane restraint degree of butt weldment for unit blocks. The effect of other variables on the transverse residual stress was very small relatively. Based on the results, it can be concluded that the proper distance between fillet weldment for stiffener and butt weldment for joining unit blocks should be determined in consideration of in-plane restraint intensity of butt weldments.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.6
• /
• pp.598-604
• /
• 2007

The purpose of this study is to establish the predictive method of welding distortion and residual stress for the channel I butt SA (submerged arc) weldment using FEA. In order to do it, the heat input model for the weldment was defined as the combined heat source with the surface heat flux of gaussian distribution and volumetric heat source uniformly distributed within weld groove by comparing the shapes of molten pool and temperature distribution obtained by FEA with those of experiments. The arc efficiency of SA welding for two-dimensional FE analysis was evaluated as 0.85. The welding distortion and residual stress of the weldment obtained by FEA and heat input model proposed have a good agreement with those obtained by experiment. Based on the results, it was suggested that the proper heat input model should be required to evaluate the welding distortion for weldment.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.63-71
• /
• 2011

Three-dimensional finite element analysis is performed to study the temperature distribution phenomenon of TIG assisted friction stir welding (TAFSW) between dissimilar plates (Al 6061-T6 and stainless steel 304). TAFSW is a solid-state welding process that integrates TIG (Tungsten Inert Gas) into a friction stir welding (FSW), to preheat the harder material ahead of FSW tool during welding. In order to facilitate the industrial application of welding, 3D numerical modeling of heat transfer has been carried out applying Finite Element Method (FEM). The temperature distribution due to heat generation during TAFSW on dissimilar materials joint is analysed using in-house solver. Moving heat source along with frictional heat between the work specimens and tool surface is considered to calculate the heat input. The analytical model used predicts successfully the maximum welding temperatures that occur on the dissimilar materials during TAFSW. Comparison with the infra red camera and thermocouple measurement results shows that the results from the current numerical simulation have good agreement with the measured data.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.102-102
• /
• 2009

The purpose of this study is to establish the predictive equation of transversal residual stress at the thick weldment of large container ship. In order to do it, the variables used for this study were restraint degree, yield strength of base material, thickness of weldment and welding heat input. Here, the level of restraint degree at the thick weldment of container ship having the various welding sequence was calculated using FEA. From the result, the h-type specimen was designed to simulate the level of restraint degree at the actual weldment of containership. With H-type test specimen designed, the effect of the variables on the distribution of transversal residual stress at the weldment in a container ship was evaluated using the comprehensive FEA. Based on the results, the predictive equations of mean value and the distribution of transverse residual stress in each location of residual stress were established using dimensional analysis and multiple-regression method. The validation of predictive equations was verified by comparing with measured results by XRD in the actual weldment of the ship.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.101-101
• /
• 2009

The purpose of this study is to develop the control technology of the welding distortion caused by Auto NG-GTA welding process at the STS 304 multi-pass butt weldment. For it, heat input model for Auto NG-GTA welding process was established and verified by measuring temperature change and molten pool shape at the bead-on-plate weldment. With heat input model developed, the effect of the tension load on the amount of welding distortion at the STS 304 multi-pass butt weldment was evaluated using the thermo-elasto-plastic FE analysis. In accordance with FEA results, the angular distortion and transverse shrinkage sharply decreased with an increase in tension load. This result indicates that tensioning method was verified as a countermeasure against the welding distortion of STS 304 multi-pass butt weldment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1069-1075
• /
• 2012

Laser is high density heat source, so it can make high speed welding with minimum heat input possible. Especially the high power fiber laser is recently commercialized and has high beam quality and the smallest system size compared with conventional laser due to it's unique oscillating mechanism. Because of these advantages it's thought that the most suitable heat source for LNG cargo tank welding precess which has to be conducted inside of ships. In this study fiber laser was used for welding of stainless steel for LNG carrier to applicate laser welding technique for shipbuilding industry. 1.2mmt STS304L of austenite stainless steel which apply to cargo tank was used for fiber laser welding. Butt and lap welding was conducted changing laser power, welding speed, then penetration characteristic was analyzed and optimal parameters for each materials. Consequently, we found that same or better mechanical properties were obtained in weld compared to base metal.